Hopp til innhold
Hjem / Biler / El-biler / Traxxas Biler / Traxxas 82224-4 TRX-4 Sport Scale Crawler Truck 1/10 RTR Clipless Grå
-10%

Traxxas 82224-4 TRX-4 Sport Scale Crawler Truck 1/10 RTR Clipless Grå

Art.nr: TRX 82224-4 GRAY

4.495,-

4.995,-

- 10%
Traxxas

Traxxas
På lager: 1

På lager i vår butikk i Oslo

Produktet er midlertidig utsolgt. Dersom du ønsker å motta en epost når vi får det inn på lager, kan du legge igjen epostadressen din i skjemaet under.

Informasjon

Traxxas 82044-4-GREY - TRX-4 Sport High Trail Edition - GREY



Purpose Built
TRX-4® Sport combines the unbeatable ground clearance and driving dynamics of Traxxas portal axles, sticky Canyon Trail™ tires, and a clipless lightweight pickup truck body for a leaner, performance-focused truck. The Sport’s unique bumpers, wheels, and body were designed for increased climbing versatility. Whether it’s a fun trail run or a hardcore technical crawl, the TRX-4 Sport’s capability and performance-built approach takes your outdoor adventure to a new level.

New Clipless Body Mounting
New to TRX-4 Sport, clipless body mounting combines clean flowing lines with secure latching convenience. TRX-4 Sport’s hidden latches hold tight on the trail no matter how intense the action gets, but release in just seconds to access the chassis.





Features:

Trail-Tuned XL-5 HV Waterproof Electronic Speed Control

  • Fully waterproof design
  • Traxxas EZ-Set® one-button setup
  • Large, efficient heat sink
  • Wide voltage latitude 6–7 cell NiMH (7.2–8.4V) and 2–3s LiPo (7.4–11.1V)
  • Two stage low voltage protection (LVD)
  • Five drive profiles:
  • Sport Mode — forward / brake / reverse
  • Race Mode — forward / brake / no reverse
  • Training Mode™ — 50% forward / 100% brake / 50% reverse (patented)
  • Trail Mode — forward / brake / reverse / with trail-tuned drag brake in neutral
  • Crawl Mode — forward / instant reverse - no neutral with 100% hill holding brake

Motor

  • Powerful Titan™ 21T reverse rotation motor with internal cooling fan
  • Precise preset gear mesh adjustments
  • Motor retention separate from gear mesh

Portal Axles

  • Increase ground clearance
  • Eliminate torque twist
  • Steel gears
  • Improve axle geometry and reduce strain on driveshafts

Rigid Steel Frame

  • 1.5 mm thick steel frame rails increase torsional rigidity
  • Innovative design allows four wheelbase positions (300mm, 312mm, 324mm, 336mm)
  • Adjustable rear shock tower positions for SWB and LWB configurations
  • Bumpers adjust fore and aft
  • Rugged rock rails adjust for width
  • Wire routing clips integrated into frame rails

Drivetrain

  • Full-time shaft driven 4-wheel drive
  • Tough 6 mm stub axles
  • Steel front CV driveshafts
  • Hardened steel rear axle shafts
  • Spool-locked front and rear differentials
  • Steel gear transfer case

Innovative Battery Compartment

  • Hinged battery strap allows quick and easy battery access
  • No pins to lose
  • Accommodates different height batteries
  • Accepts full-size long battery packs
  • Integrated compartment accepts smaller 1/16 scale batteries (with optional strap)

Transmission

  • Single-speed with steel gears
  • Dual horizontal shafts
  • Twin friction plate slipper clutch
  • Easily removed for servicing

Steering

  • Chassis mounted 2075X metal gear digital servo
  • Superior 45° steering angle
  • Direct steering (no servo saver)
  • Steering geometry corrected for bump steer

Suspension

  • Front — 3 link with panhard
  • Rear — triangulated 4 link
  • Heavy-duty rod ends with steel hollow balls
  • 5mm diameter steel link rods with 4mm threaded ends

Aluminum GTS Shocks

  • Oil-filled coilover GTS shocks exclusive to TRX-4 chassis
  • Silver-anodized aluminum bodies
  • Threaded bodies with collars easily adjust ride height
  • Silky smooth damping for the toughest trails
  • O-ring cap seal and dual X-ring shaft seals

Wheels and Tires

  • Rugged black 5-spoke wheels
  • Pre-mounted 1.9” Canyon Trail tires with trail-tuned foam inserts
  • Trail tuned S1 rubber compound
  • 12mm steel hex

 

  • TQ™ 2.4GHz 2-channel transmitter
  • Patented O-Ring Sealed Watertight Receiver Box Keeps the Micro Receiver Dry
  • Sealed Ball Bearings
  • Hex Hardware with Rust-Resistant Black Oxide Coating


TRX-4 SPORT DATA:

  • Length: 557 mm
  • Front Track: 249 mm
  • Rear Track: 249 mm
  • Ground Clearance: 80 mm
  • Weight: 2.63 kg
  • Height: 241 mm
  • Wheelbase: 312 mm
  • Approach Angle: 58.82°
  • Departure Angle: 45.83°
  • Breakover Angle: 58.93°
  • Front Shock Length: 90 mm
  • Rear Shock Length: 90 mm
  • Front Wheels: 1.9 x 1.02 inches (49 x 26 mm)
  • Rear Wheels: 1.9 x 1.02 inches (49 x 26 mm)
  • Front Tires: 4.64 x 1.89 inches (118 x 48 mm)
  • Rear Tires: 4.64 x 1.89 inches (118 x 48 mm)
  • Hex Size: 12 mm
  • Speed Control: XL-5 HV
  • Motor (electric): 21T Reverse Rotation
  • Transmission: Single Speed
  • Gear Pitch: 32P
  • Differential Type: Locked Spool
  • Chassis Structure / Material: Steel Ladder Frame with Nylon Composite Crossmembers
  • Brake Type: Electronic “Hill Hold”
  • Drive System: Shaft Driven 4WD
  • Steering: Chassis Mounted Servo
  • Servo: 2075X Metal Gear
  • Transmitter: TQ™ 2.4GHz 2-Channel Transmitter
  • Receiver: 6519
  • Skill Level: 2
  • Battery Tray: L158.75 x W47 x H23/26 mm


XL-5 HV ESC Specs:

  • Input Voltage: 6–7 Cells NiMH, 2–3s LiPo
  • Case Size: 1.23” W x 2.18” D x 1.04” H
  • Weight: 74 g
  • Motor Limit: 21-turns (550 size)
  • On Resistance Forward: 0.004 Ohms
  • On Resistance Reverse: 0.004 Ohms
  • Peak Current - Forward: 100A
  • Peak Current - Reverse: 100A
  • Braking Current: 60A
  • Continuous Current: 18A
  • BEC Voltage: 6.0 VDC
  • BEC Current: 1A
  • Power Wire: 14 Gauge / 5”
  • Input Harness Wire: 26 Gauge / 14.5”
  • ransistor Type: MOSFET
  • PWM Frequency: 1700Hz
  • Low Voltage Detection (LVD): 2-Stage indicators, switchable (on or off)
  • Thermal Protection: Thermal Shutdown
  • Single-button setup: Yes, Traxxas EZ-Set®


Profile selection: 

  • Sport Mode: 100% FWD, 100% brakes, 100% REV
  • Race Mode: 100% FWD, 100% brakes, no REV
  • Training Mode:* 50% FWD, 100% brakes, 50% REV
  • Trail Mode: 100% FWD, 100% Brake, 100% REV, Trail-Tuned Brake on Neutral
  • Crawl Mode: 100% FWD, 100% Instant REV, 100% Brake on Neutral

* Patented

Motor Specs:

  • Type: High-torque brushed motor
  • Size: 550
  • Weight: 390 g
  • Length: 78mm (Overall) - 57 mm (Can) - 38.9 mm diameter
  • Turns: 21T reverse rotation
  • Voltage: 16.8V


What’s In The Box:

  • TRX-4, Ready-To-Drive® model
  • XL-5 HV waterproof electronic speed control
  • Titan™ 21T reverse rotation motor
  • TQ™ 2.4GHz radio system
  • High quality maintenance tools


What You’ll Need:

  • Batteries: TRX-4 accepts a wide variety of NiMH (4–7 cell) and LiPo (2s–3s) batteries.
  • Charger: Traxxas EZ-Peak Live charger is recommended for easy and fast charging performance (model #2971).
  • AA Alkaline Batteries: Four AA alkaline batteries for the transmitter.

Produsent

Traxxas

Traxxas

Dette er den beste merket for RC-BIL i hele Norge, nei vi kan vel si hele verden uten å trenge å være redd for at vi sier noe galt!

Dekk & Felger

Trykk her!

Reservedeler

Trykk her!

Options parts

Trykk her!

Body/Karosseri

Trykk her!

Servo

Trykk her!

Batteri

Trykk her!

Ladere

Trykk her!

Relaterte produkter

 

Hovedbilde Traxxas 82224-4 TRX-4 Sport Scale Crawler Truck 1/10 ... Hovedbilde Traxxas 82224-4 TRX-4 Sport Scale Crawler Truck 1/10 ...
Traxxas 82224-4 TRX-4 Sport Scale Crawler Truck 1/10 ...
Art.nr: TRX 82224-4 BLUE
Copied
Traxxas TRX82224-4-BLUE - TRX-4 Sport Clipless - BLUE Purpose Built TRX-4® Sport combines the unbeatable ground clearance and driving dynamics of Traxxas portal axles, sticky Canyon Trail™ tires, and a clipless lightweight pickup truck body for a leaner, performance-focused truck. The Sport’s unique bumpers, wheels, and body were designed for increased climbing versatility. Whether it’s a fun trail run or a hardcore technical crawl, the TRX-4 Sport’s capability and performance-built approach takes your outdoor adventure to a new level. New Clipless Body Mounting New to TRX-4 Sport, clipless body mounting combines clean flowing lines with secure latching convenience. TRX-4 Sport’s hidden latches hold tight on the trail no matter how intense the action gets, but release in just seconds to access the chassis. Features: Trail-Tuned XL-5 HV Waterproof Electronic Speed Control Fully waterproof design Traxxas EZ-Set® one-button setup Large, efficient heat sink Wide voltage latitude 6–7 cell NiMH (7.2–8.4V) and 2–3s LiPo (7.4–11.1V) Two stage low voltage protection (LVD) Five drive profiles: Sport Mode — forward / brake / reverse Race Mode — forward / brake / no reverse Training Mode™ — 50% forward / 100% brake / 50% reverse (patented) Trail Mode — forward / brake / reverse / with trail-tuned drag brake in neutral Crawl Mode — forward / instant reverse - no neutral with 100% hill holding brake Motor Powerful Titan™ 21T reverse rotation motor with internal cooling fan Precise preset gear mesh adjustments Motor retention separate from gear mesh Portal Axles Increase ground clearance Eliminate torque twist Steel gears Improve axle geometry and reduce strain on driveshafts Rigid Steel Frame 1.5 mm thick steel frame rails increase torsional rigidity Innovative design allows four wheelbase positions (300mm, 312mm, 324mm, 336mm) Adjustable rear shock tower positions for SWB and LWB configurations Bumpers adjust fore and aft Rugged rock rails adjust for width Wire routing clips integrated into frame rails Drivetrain Full-time shaft driven 4-wheel drive Tough 6 mm stub axles Steel front CV driveshafts Hardened steel rear axle shafts Spool-locked front and rear differentials Steel gear transfer case Innovative Battery Compartment Hinged battery strap allows quick and easy battery access No pins to lose Accommodates different height batteries Accepts full-size long battery packs Integrated compartment accepts smaller 1/16 scale batteries (with optional strap) Transmission Single-speed with steel gears Dual horizontal shafts Twin friction plate slipper clutch Easily removed for servicing Steering Chassis mounted 2075X metal gear digital servo Superior 45° steering angle Direct steering (no servo saver) Steering geometry corrected for bump steer Suspension Front — 3 link with panhard Rear — triangulated 4 link Heavy-duty rod ends with steel hollow balls 5mm diameter steel link rods with 4mm threaded ends Aluminum GTS Shocks Oil-filled coilover GTS shocks exclusive to TRX-4 chassis Silver-anodized aluminum bodies Threaded bodies with collars easily adjust ride height Silky smooth damping for the toughest trails O-ring cap seal and dual X-ring shaft seals Wheels and Tires Rugged black 5-spoke wheels Pre-mounted 1.9” Canyon Trail tires with trail-tuned foam inserts Trail tuned S1 rubber compound 12mm steel hex   TQ™ 2.4GHz 2-channel transmitter Patented O-Ring Sealed Watertight Receiver Box Keeps the Micro Receiver Dry Sealed Ball Bearings Hex Hardware with Rust-Resistant Black Oxide Coating TRX-4 SPORT DATA: Length: 557 mm Front Track: 249 mm Rear Track: 249 mm Ground Clearance: 80 mm Weight: 2.63 kg Height: 241 mm Wheelbase: 312 mm Approach Angle: 58.82° Departure Angle: 45.83° Breakover Angle: 58.93° Front Shock Length: 90 mm Rear Shock Length: 90 mm Front Wheels: 1.9 x 1.02 inches (49 x 26 mm) Rear Wheels: 1.9 x 1.02 inches (49 x 26 mm) Front Tires: 4.64 x 1.89 inches (118 x 48 mm) Rear Tires: 4.64 x 1.89 inches (118 x 48 mm) Hex Size: 12 mm Speed Control: XL-5 HV Motor (electric): 21T Reverse Rotation Transmission: Single Speed Gear Pitch: 32P Differential Type: Locked Spool Chassis Structure / Material: Steel Ladder Frame with Nylon Composite Crossmembers Brake Type: Electronic “Hill Hold” Drive System: Shaft Driven 4WD Steering: Chassis Mounted Servo Servo: 2075X Metal Gear Transmitter: TQ™ 2.4GHz 2-Channel Transmitter Receiver: 6519 Skill Level: 2 Battery Tray: L158.75 x W47 x H23/26 mm XL-5 HV ESC Specs: Input Voltage: 6–7 Cells NiMH, 2–3s LiPo Case Size: 1.23” W x 2.18” D x 1.04” H Weight: 74 g Motor Limit: 21-turns (550 size) On Resistance Forward: 0.004 Ohms On Resistance Reverse: 0.004 Ohms Peak Current - Forward: 100A Peak Current - Reverse: 100A Braking Current: 60A Continuous Current: 18A BEC Voltage: 6.0 VDC BEC Current: 1A Power Wire: 14 Gauge / 5” Input Harness Wire: 26 Gauge / 14.5” ransistor Type: MOSFET PWM Frequency: 1700Hz Low Voltage Detection (LVD): 2-Stage indicators, switchable (on or off) Thermal Protection: Thermal Shutdown Single-button setup: Yes, Traxxas EZ-Set® Profile selection:  Sport Mode: 100% FWD, 100% brakes, 100% REV Race Mode: 100% FWD, 100% brakes, no REV Training Mode:* 50% FWD, 100% brakes, 50% REV Trail Mode: 100% FWD, 100% Brake, 100% REV, Trail-Tuned Brake on Neutral Crawl Mode: 100% FWD, 100% Instant REV, 100% Brake on Neutral * Patented Motor Specs: Type: High-torque brushed motor Size: 550 Weight: 390 g Length: 78mm (Overall) - 57 mm (Can) - 38.9 mm diameter Turns: 21T reverse rotation Voltage: 16.8V What’s In The Box: TRX-4, Ready-To-Drive® model XL-5 HV waterproof electronic speed control Titan™ 21T reverse rotation motor TQ™ 2.4GHz radio system High quality maintenance tools What You’ll Need: Batteries: TRX-4 accepts a wide variety of NiMH (4–7 cell) and LiPo (2s–3s) batteries. Charger: Traxxas EZ-Peak Live charger is recommended for easy and fast charging performance (model #2971). AA Alkaline Batteries: Four AA alkaline batteries for the transmitter.

4.495,-

4.995,-

På lager 1
KJØP
-10%
Hovedbilde Yeah Racing Bearing Set with Bearing Oil For Traxxas ... Hovedbilde Yeah Racing Bearing Set with Bearing Oil For Traxxas ...
Yeah Racing Bearing Set with Bearing Oil For Traxxas ...
Art.nr: YB0302BX
Copied
Yeah Racing RC PTFE Bearing Set with Bearing Oil For Traxxas TRX-4 (Ver.2) Features: RC Ball bearings should always be your first upgrades, it reduces friction for less rolling resistance, and that means higher speed and longer the running times. RC Ball bearings hardly require maintenance and last a lot longer than stock Oilite bushings. Yeah Racing RC Ball Bearings have the lowest resistance. They are manufactured by Aircraft quality steel. Pre-lubricated to ensure its excellent performance! These high quality bearings outweigh the other low quality one: Aircraft quality material More durable Higher precision *Now comes with bearing oil for maintaining bearings in long run. (This new bearing set (with bearing oil) will replace the old item.)   Specifications: Material: Steel Shielding: Rubber   Includes: Bearing (40 Pcs) -4X10X4(4pcs) -5X8X2.5(3pcs) -5X10X4(1pc) -5X11X4(12pcs) -6X12X4(4pcs) -6X13X5(6pcs) -10X15X4(4pcs) -12X18X4(2pcs) -7x14x5(2pcs) (ver.2) -15x21x4mm(2pcs) (ver.2) Bearing Oil (15ml) #YA-0215(1pc)   Tips on Cleaning & Lubricating Ball Bearings (RC Bearing Tips) Tips for Handling New Ball Bearing: Most competition RC racers will clean the grease on the new ball bearings and apply ball bearing oil on them. (i.e. Yeah Racing High Speed Bearing Oil / Lube #YA-0215). As re-oiling the ball bearing allows the RC cars to run smoother and makes the bearings more durable.

329,-

349,-

På lager 1
KJØP
-6%
Hovedbilde Traxxas 8085X LED Light Set Pro Scale Complete TRX-4 ... Hovedbilde Traxxas 8085X LED Light Set Pro Scale Complete TRX-4 ...
Traxxas 8085X LED Light Set Pro Scale Complete TRX-4 ...
Art.nr: TRX 8085X
Copied
Traxxas 8085X TRX-4 Sport Pro Scale® LED Light Set All the lighting control of a full-scale truck is at your fingertips with the Pro Scale® LED Light Set for your TRX-4® Sport. Turn the headlights on and off and select high or low beams. Signal for turns with automatic cancellation or put on the hazard lights. The brake lights glow when you slow or stop. Hit reverse, and backup lights glow automatically. For maximum power and convenience, add Traxxas Link and the optional Wireless Module (Part #6511, sold separately) to configure your lights right from your iOS or Android device. The Pro Scale system makes it easy. Pro Scale® Light Set Features: Headlights with high/low beam settings Brake lights Reverse lights Turn signals with auto-cancellation Hazard lights Set Includes: Complete LED light Set Pro Scale Lighting Power Module and mount Pro Scale Lighting Distribution Block and mount Motor sensors wire harness Front and rear light harness Receiver communication cable Installation hardware  

1.249,-

1.349,-

På lager 1
KJØP
-7%
Hovedbilde Traxxas 8085 LED Head- and Tail Light Kit with Power ...
Traxxas 8085 LED Head- and Tail Light Kit with Power ...
Art.nr: TRX 8085
Copied
  TRX-4 Sport LED LIGHT KIT (#8085) Genuine Traxxas LED light kits for the TRX-4 Sport are engineered with the same outstanding quality and attention to detail as the truck itself. Precise Traxxas fit and finish makes installation easy and fun for any skill level, and the waterproof design allows for all-weather adventure after the sun goes down. An injection molded grill and tailgate with integrated lenses adds scale detail and rugged functionality. FEATURES: Sealed waterproof design Engineered by Traxxas for direct fit on the TRX-4 Sport body with tidy and secure wire management Color-coded power distribution block for easy and secure connections Includes front grill and rear tailgate with integrated lenses Traxxas LED lighting module: Regulated to provide consistent and reliable power output with batteries from NiMH to 3S LiPo Eliminates overheating, glitching, and other electronics issues common with unmatched aftermarket systems #8085 Kit Contents: LED lighting module Distribution block Front grill Front grill retainer Headlights harness assembly Headlight clamps (2) Tailgate panel Tailgate panel retainer Tail lights harness assembly Tail light clamps (2) 2.5x8mm button-head screws (8) 2.6x8mm button-head screws (2) 2.5x10mm button-head screws (2) 2.5x15mm cap screws (2) Zip tie mount (3) Zip ties (3) Body templates

739,-

769,-

På lager 3
KJØP
-4%
Hovedbilde Traxxas 9130 Blå TRX-4 1972 Blazer Body Kit
Traxxas 9130 Blå TRX-4 1972 Blazer Body Kit
Art.nr: TRX 9130-BLUE
Copied
TRX-4 1972 Blazer Body Kit The TRX-4 1972 Chevrolet® Blazer clipless body faithfully reproduces one of the most iconic Chevy trucks to ever hit the trail. Bright chrome accents contrast the high-gloss paint for an unmistakable look. The injection-molded grille, side mirrors, and simulated wood trim give K5 Blazer uncompromising scale presence. (Requires 312 mm wheelbase and 8072X inner fenders) Replacement part for these models: TRX-4 1972 Chevrolet Blazer High Trail Edition Accessory part for these models: TRX-4 Sport High Trail Edition

1.795,-

1.995,-

På lager 1
KJØP
-10%
Hovedbilde Traxxas 9130 Body Chevrolet Blazer ´72 Clear w Trim
Traxxas 9130 Body Chevrolet Blazer ´72 Clear w Trim
Art.nr: TRX 9130
Copied
Body Chevrolet Blazer ´72 Clear w Trim Body, Chevrolet Blazer (1972) (clear, requires painting)/ decals/ window masks (includes grille, side mirrors, door handles, windshield wipers, clipless mounting, hardware) (requires #8072X inner fenders) From mild to wild, Traxxas clear bodies are your own personal canvas. You choose the color and design and Traxxas ProGraphix® paint makes it easy to get professional quality results. The clear TRX-4® 1972 Chevrolet® Blazer clipless body kit comes fully-trimmed for easy mounting. The kit includes body accessories, mounting hardware, window masking, and decals. (Requires 312 mm wheelbase and 8072X inner fenders)

1.495,-

1.695,-

På lager 1
KJØP
-12%
Hovedbilde Traxxas 9130 Rød TRX-4 1972 Blazer Body Kit
Traxxas 9130 Rød TRX-4 1972 Blazer Body Kit
Art.nr: TRX 9130-RED
Copied
TRX-4 1972 Blazer Body Kit The TRX-4 1972 Chevrolet® Blazer clipless body faithfully reproduces one of the most iconic Chevy trucks to ever hit the trail. Bright chrome accents contrast the high-gloss paint for an unmistakable look. The injection-molded grille, side mirrors, and simulated wood trim give K5 Blazer uncompromising scale presence. (Requires 312 mm wheelbase and 8072X inner fenders) Replacement part for these models: TRX-4 1972 Chevrolet Blazer High Trail Edition Accessory part for these models: TRX-4 Sport High Trail Edition

1.795,-

1.995,-

På lager 1
KJØP
-10%

Kunder kjøpte også

Hovedbilde Traxxas 581344 Oransje Slash 2WD 1/10 RTR TQ BL-2S Hovedbilde Traxxas 581344 Oransje Slash 2WD 1/10 RTR TQ BL-2S
Traxxas 581344 Oransje Slash 2WD 1/10 RTR TQ BL-2S
Traxxas 58134-4-ORANGE- Slash 2WD BL-2S Brushless RTR - Oransje The Evolution Of An Icon Traxxas Slash® puts you in the driver’s seat for intense fender-to-fender short course racing action at the track, or in your own backyard. Slash’s all-new BL-2s™ brushless power system delivers effortless power for all-day fun with a more responsive throttle and powerful acceleration. The rear-wheel drive Slash is purpose built to fly over jumps and rip full-throttle through the turns. The fully adjustable track-ready suspension replicates real-world dynamics for the most authentic short course racing experience possible. BL-2s Power System The new BL-2s brushless power system is an absolute game-changer with 15% more speed, quicker acceleration, and a more responsive throttle. Improved efficiency, high-speed ball bearings, and an internal cooling fan allow Slash to run battery after battery for all-day race sessions. With no brushes to wear out, the BL-2s 3300 kV motor can last the entire racing season with minimal maintenance. Track-Ready Performance From sanctioned races at the local track to backyard bash sessions, Slash is Ready-To-Race® right out of the box. Slash’s track-bred chassis features an integrated transponder mount and extended battery tray for optimum weight positioning. Slash gives you the winning edge with a fully adjustable steel-link suspension and metal-gear differential to put the power down smoothly. Clipless Body Mounting Slash’s revolutionary clipless body holds firm no matter how rough the racing gets. Heavy-duty latches grip the body tightly, but release in just seconds for fast battery swaps on the pit bench. This convenient hidden latching system replaces traditional body clips with large, reinforced panels to maintain body integrity and resist pull-through damage. Specs: Length: 578 mm Width: 296mm Center Ground Clearance: 89mm Weight (no battery): 2.18kg Height (overall): 193mm Wheelbase: 335mm Shock Length (front): 88mm - Long Shock Length (rear): 101mm - XX-long Tires: BFGoodrich® Mud Terrain T/A® Tire Diameter: 109 mm (43 mm wide) Wheels (front/rear): 2.2/3" Satin-finish Wheel Diameter: 2.2" (56mm) (outer) 3" (76mm) (inner) Speed Control: BL-2s™ electronic speed control Motor (electric): BL-2s™ 3300 kV sensorless brushless Overall Drive Ratio: 2.72 (final drive: 12.58) Differential Type: Steel composite planetary Gear Pitch: 48 pitch Chassis Structure/Material: Composite tub Drive System: 2WD Steering: Dual bellcrank Radio System: TQ™ 2.4 GHz (2-channel) Servo: Waterproof digital 2075 Top Speed: 56+ kph Skill Level: 1 Battery Compartment: L165 x W50 x H23/25mm Required Batteries: 4 “AA” (transmitter), Vehicle (see battery finder) What’s In The Box: Slash 2WD with BL-2s ESC and 3300 kV motor Quick Start Guide TQ™ 2.4 GHz radio system High quality maintenance tools What You’ll Need: Batteries: Slash requires a single NiMH or LiPo battery. See full list of batteries. Charger: Traxxas EZ-Peak Live charger (2971) is recommended for easy and fast charging performance. AA Alkaline Batteries: Four AA alkaline batteries for the transmitter.

3.995,-

** Ikke på lager
KJØP
Hovedbilde Traxxas 8332 Caster Blocks (2)
Traxxas 8332 Caster Blocks (2)
Caster blocks (c-hubs) (2)/ kingpin bushings (4)

49,-

På lager 1
KJØP
Hovedbilde Tamiya 58679 Suzuki Swift Sport (M-05) Pre-painted ... Hovedbilde Tamiya 58679 Suzuki Swift Sport (M-05) Pre-painted ...
Tamiya 58679 Suzuki Swift Sport (M-05) Pre-painted ...
The Tamiya M-05 chassis is a fun, simple on-road chassis that takes front wheel drive mechanics and puts replica compact cars on top for fun driving thrills. This kit recreates the Suzuki Swift sport. The Swift underwent a full model change in 2017, and impressively managed to improve overall design rigidity while getting lighter. It was given a wider tread, a direct injection 1.4-liter inline-4 engine and 6-speed automatic transmission. The Tamiya assembly kit faithfully captures the body and its details in tough polycarbonate material with the body already pre-painted! 1/10 scale R/C model assembly kit. Length: 381mm, width: 167mm. Lightweight, durable polycarbonate body pre-painted in yellow. Wheel arches and the separate polycarbonate light cases come pre-cut. Separate injection molded parts are included to recreate side mirrors. •The M-05 chassis is a compact unit based around a lightweight monocoque and offering great weight distribution with a low center of gravity. This model uses the 239mm L wheelbase. Comes with marking stickers to decorate the body. The popular M-05 chassis has a wide range of Hop-Up Option parts available to tune the chassis to any flat surface. Includes Tamiya 540-motor. Includes: Tamiya TBLE-02S ESC (electronic speed control) Capable of running sensor brushless motors and brushed motors alike. (21.5 Turn BL motor limit) (23 Turn brushed motor limit) Required Items: 2-channel radio, steering servo, 7.2volt battery pack with compatible charger.

1.995,-

2.295,-

På lager 1
KJØP
-13%
Hovedbilde Traxxas 5032 Silicon Shock Oil Premium 30WT (350cSt) ... Hovedbilde Traxxas 5032 Silicon Shock Oil Premium 30WT (350cSt) ...
Traxxas 5032 Silicon Shock Oil Premium 30WT (350cSt) ...
Traxxas 30WT/350cSt Premium Shock Oil 60ml New from Traxxas is a complete line of premium silicone shock oil. Available in seven steps of viscosity, this 100% pure silicone oil allows precise vehicle suspension tuning for maximum performance, no matter where you drive. The precision-pour, the twist-nozzle cap makes it quick and easy to fill shock bodies, without all the mess. cSt viscosity specification ensures consistent performance with every bottle. Features: Seven precise viscosities ranging from 200cSt to 1000cSt (20wt to 80wt) 100% silicone oil for maximum consistency Precision-pour, twist-nozzle cap Specs: Viscosity: 30WT (350cSt) Bottle size: 60ml

99,-

109,-

På lager 7
KJØP
-9%
Hovedbilde Bronto Ladekabel - XT60 til T-Plugg (Deans)
Bronto Ladekabel - XT60 til T-Plugg (Deans)
  Bronto ladekabler er et must for RC-entusiasten. Ladekabelen er utstyrt med kvalitets 14AWG ledninger. Ladeledningen har en praktisk lengde på 30cm, noe som er godt egnet når du f.eks skal legge batteriet trygt i en sikker ladebag mens det lades. Ladekabel med T-plug til XT60-plugger. Benyttes for lading av batterier med T-plugg, og kobles rett i ladere med XT60 tilkobling. Spesifikasjoner   Ledning 14AWG Lengde 30cm Tilkobling 1 XT60 Tilkobling 2 T-Plugg (også kjent som Deans)

79,-

På lager 13
KJØP
Hovedbilde CHHL Racing Series 2S 5200mAh - 100C - Deans - ... Hovedbilde CHHL Racing Series 2S 5200mAh - 100C - Deans - ...
CHHL Racing Series 2S 5200mAh - 100C - Deans - ...
CHHL Racing Series 2S 5200mAh - 100C - Deans - Hardcase Dimensjonene er 139x47x25 og passer i ett utvalg med 1/10-biler med mer. Deans-type kontakt.   Spesifikasjoner: Kapasitet: 5200mAh Spenning: 2S 7.4V Vekt: 266.5gram Størrelse: 139x47x25mm Strømplugg:    Deans

399,-

429,-

På lager 6
KJØP
-7%
Hovedbilde DEANS FEMALE INCLUDING HEAT SHRINK (BATTERY END) ...
DEANS FEMALE INCLUDING HEAT SHRINK (BATTERY END) ...
Radient

39,-

På lager 1
KJØP
Hovedbilde Bronto XH Balanseringsforlenger 2s - 20cm Hovedbilde Bronto XH Balanseringsforlenger 2s - 20cm
Bronto XH Balanseringsforlenger 2s - 20cm
Praktisk kabel for å forlenge balanseringskontakten på batterier med XH balanseringskontakt. Gjør det enklere å få sikret ladingen i lipo-ladeposer, eller å lade batteriet uten å ta det ut av modellen. Spesifikasjoner Type XH For antall seller 2s Ledning 22AWG Lengde 20cm

39,-

På lager 2
KJØP
Hovedbilde
"Bulk" Carson Speed Controller Dragster Brushed 70A
*** This is a Brand new item taken from a kit (chopped part), therefore will not have a Tamiya packaging *** Article number: 500906264 Product: Speed Controller Dragster Brushed 70A The sensitive speed controller for 1:10 RC models is waterproof and can therefore be installed in boats. Of course, it can also be used in 1:10 buggies, on-road, off-road vehicles and crawlers. The controller is designed for 2 to 3 LiPo cells. With a T-plug connector adapter, NiMH batteries can also be used. Included: Elektric speed controler Dragster Brushed 70 A,Tamiya/T-Plug adapter, manual.

399,-

439,-

Kontakt oss for mer informasjon om dette produktet
Ikke på lager
-9%
Hovedbilde SkyRC D100 Neo Dobbel Computerlader AC100W Hovedbilde SkyRC D100 Neo Dobbel Computerlader AC100W
SkyRC D100 Neo Dobbel Computerlader AC100W
SkyRC D100 Neo er ett godt valg for deg som ønsker en kompakt og kraftig lader med mulighet til å lade 2 batterier samtidig. D100 Neo har en makseffekt vil gi deg muligheten for 100W lading med AC og 200W DC fordelt på de 2 ladeutgangene. Maks ladestyrke er 10A per port. Laderen bruker skrollehjul og knapp og har også innebygget balanserer og XT60-type tilkoblingspunkter. Laderen har også en USB-C PD-port som gir deg muligeten til å lade mobil og andre dingser på opp til 20W. Denne laderen er en multilader som kan lade LiPo, LiHV, LiFe, LiIon, NiHm, NiCd og Pb batterier. Laderen går på vanlig nettstrøm 220V, eventuelt på 10-30V DC. Det følger med 220V strømkabel, batterier med XT60-kontakt kobles direkte i XT60-utgang på laderen. Skal man lade batterier med annen type batteriplugg må overgang benyttes, dette må kjøpes løst. XH-balanseringsplugg plugges direkte i balanseringsutgangen på lader. Spesifikasjoner: Vekt 470gram Innspenning AC 100-240V Innspenning DC 10-30V Display 2.8" m/Farge Størrelse 116x110x79mm Antall celler LiPo 1-6 Antall celler NiMh/NiCD 1-15 Discharge 5-25W Ladestyrke 0.1-10,0A Viktig info! Husk at ved lading av lipo batterier skal man for å oppnå full balansering av pakken kople til begge kontaktene fra batteriet og velge LiPo Balance programmet, ikke LiPo Charge. Inkludert i eska: D100 Neo Duo-laderen, engelsk manual og 220V strømkabel. SkyRC D100neo - Dual Charging Station 2x100W - 240VAC or 10-30VDC input Dual Input/Output: Unleash the Thrill! Experience the next level of charging with SkyRC D100neo, the latest and upgraded version of D100 charger, packed with innovative features and improved functionality. Featuring two charging ports, SkyRC D100neo delivers a total power of 200W and 10A per port, allowing simultaneous charging of multiple chemistry batteries. With a balance current of 1000mA per cell, it speeds up balancing among battery cells, enhancing the charging process. The high precision balancer ensures impressive accuracy of ±0.02V, optimizing voltage equalization. Whether you're a seasoned professional or a passionate hobbyist, this charger takes your RC charging to new heights. Efficient, yet Compact Outrageous performance is packed through 2 Independent ports in the compact footprint. You can simultaneously charge two RC batteries with two ports, even in different chemistry. Whether you need to power up your RC car or fly a drone, D100neo has you covered! Despite its small size, the D100neo doesn't compromise on power or efficiency with up to 200W on an output! The charger boasts a vibrant color display featuring a remarkable 76,800 pixels, surpassing the 8,192-pixel black white screen of the D100. *When powered by DC, the D100neo can output up to 200W of charging power. Do more with one charger! Multiple Chemistries Go. With exceptional versatility, D100neo can charge a wide range of battery chemistries. This powerhouse can charge from LiPo and LiFe to Li-ion, LiHV, Pb, NiMH, and NiCd. You are turbocharging your time with a single charger that can handle multiple battery types. Whether you're an RC guru, a beginner, or somewhere in between, D100neo is the reliable and adaptable choice that ensures optimal performance for all your batteries. Unlock the full potential of your battery arsenal with D100neo – versatility multiplied capability. Dual AC/DC Input D100neo is designed to provide RC enthusiasts unparalleled flexibility in the garage or out in the field. With dual port input, you have the freedom to choose between AC or DC input based on your specific scenarios. In AC mode, the charging power reaches an impressive overall 100W, dynamically distributing to each port. When powered by DC, the charger unleashes its true potential, offering an astounding overall 200W of charging power. With a single port capable of reaching up to 100W, you can power up your batteries with remarkable speed and precision. Whether you are a beginner or a seasoned RC guru engaging in racing, D100neo ensures efficient charging and optimal performance for your RC batteries. Unmatched Charging, Impressive Discharging This cutting-edge device not only offers efficient charging but also provides impressive discharging functionality. The built-in balance port enables D100neo to discharge faster, allowing it to discharge at up to 25W when used in conjunction with the main port. In contrast, the discharge rate when using the main port alone is limited to 5W. Whether you need to prepare your batteries for storage, balance their voltage levels, or safely discharge them after use, the D100neo is there for you! This advanced discharging feature allows you to maintain the health and longevity of your batteries by precisely controlling the discharge process. Smart Power Distribution - Efficiency Redefined When a single port is in use, the D100neo will provide maximum power output to that specific port. The charging power is distributed dynamically and intelligently when all two ports are simultaneously in use. Once a particular port has completed its charging task, the remaining port will receive increased power for faster charging. This intelligent and efficient allocation of power ensures optimal utilization at all times. The charging capabilities of the D100neo are highly flexible, allowing for versatile charging options. So. Pro. Digital Power D100neo excels not only in charging, but also as a versatile dual-output digital power supply. With just a few clicks on the menu, D100neo offers a voltage option, from 2V to 27V, with an adjustable increment of 0.1V. Additionally, the current can be adjusted from 0.2A to 10A, with a precision of 0.1A. This dual-output digital DC power supply provides two independently controllable power outputs, making it a versatile tool for various electronic testing and prototyping applications. Balancing batteries made quick and easy By connecting the balance port, the D100neo transforms into a versatile battery checker capable of measuring cell voltage and balancing various battery types such as LiPo, LiHV, LiFe, and LiIon. Instantly, you can view the overall voltage and individual cell voltages, helping determine whether the battery is charged, discharged, or balanced. LiPo batteries are well-known for their high energy density and lightweight nature, making proper care and monitoring essential for safety and longevity. With this functionality, the D100neo acts as a reliable safeguard for your RC batteries. 20W PD 3.0 Port Energize with Rapid Power Delivery! With the 20W USB-C PD 3.0 charging port, our RC players can enjoy rapid charging speeds like never before. Whether you're charging your smartphones, tablets, or 2020 MacBook Airs, this powerful port ensures that you can fuel up your devices in a fraction of the time. Cool charging Within the sleek enclosure lies a groundbreaking thermal system designed to let Arm Cortex-M4 fly through heavy workloads at screaming-fast speeds — and stay whisper quiet. The fan will adjust the speed accordingly and dissipate heat more effectively according to the different power usage. Charge in your language ColorX is designed to be easily localized and comfortably engaged. The interface is currently available in English, Dutch, Chinese, French and Japanese*. Users can easily change the language with simple clicks so that they can charge in the most comfortable language. (*More languages will be released by time!) Scroll to Control: Designed For Productivity This charger is engineered for performance and productivity. Say goodbye to the mundane buttons, as we've revolutionized the charging experience by introducing a precision aluminum scrolling wheel. This innovative feature not only adds a touch of comfort and style but also takes your productivity to new heights. More than just a wheel! An exclusive upgrade for a top-of-the-line charging experience is added for RC gurus! ColorX: Easy to charge, Easy on eyes. Get ready to be captivated by the sleek and modern ColorX interface by D100neo. The tailor-designed light cyan and green color scheme is optimized specifically for RC charging, which helps you focus on the setting. The Web 2.0 style, responsive menu, and well-designed icons make the operation more suitable for players accustomed to operating smartphones! Time to say bye-bye to old-school typography and welcome the bold and beautiful brand-new UI. Charging doesn't have to be boring, and neither does life! Seamlessly Connect, Effortlessly Upgrade! Effortlessly connect your D100neo to your PC or Mac via the versatile Type-C port. With Charger Master, take full control and enhance your charging experience. Customize charging rates, monitor battery health, and optimize performance for longer battery life. Upgrade with ease using the app. Enjoy a fast and reliable upgrade process to enhance your charger's capabilities. Stay connected, stay updated, and enjoy a happier charging experience. Software: Windows Mac Size & weight: Case Material: PC-ABS V0 Case Size: 116x110x79mm Weight: 470g Display: Type: TN Size: 2.8 inch Panel Active Area: 43.2x57.6mm Resolution: 240x320 Pixel Number of Colors: 262K Power: DC Input Voltage: 10-30V AC Input Voltage: 100-240V Charger power: AC: 100W MAX DC: 200W MAX Discharge power: Main port: 5W Balance port: 25W MAX (LiPo/6S) 20W USB-C Power Delivery: QC3.0: 5V⎓3A, 9V⎓2A, 12V⎓1.5A 18W PD: 5V⎓3A, 9V⎓2.2A, 12V⎓1.67A 20W Batteries: LiPo/LiHV/LiFe/LiIon: 1-6cells NiMH/NiCd: 1-15cells Pb: 3S/6S/12S Charging and Discharging: Charge current: LiPo/LiFe/LiIon/LiHV/NiMH/NiCd/Pb：0.2-10.0A Discharge current: LiPo/LiFe/LiIon/LiHV/NiMH/NiCd/Pb：0.1-2.0A Balance current: LiPo/LiFe/LiIon/LiHV：1.0A MAX Operation: LiPo/LiFe/LiIon/LiHV: Balance CHG, Charge, Storage & Discharge NiMH/NiCd: Charge, Re-Peak, CYCLE_C_D, CYCLE_D_C & Discharge Pb: Normal, AGM Charge, Cold Charge & Discharge

1.395,-

1.495,-

På lager 2
KJØP
-7%
Hovedbilde Traxxas 8337 Steering Block (2)
Traxxas 8337 Steering Block (2)
  Steering Block (2)

49,-

På lager 1
KJØP
Hovedbilde Kyosho 34427T1B Fazer MK2 Datsun 240Z 1971 Tuned Ver. ... Hovedbilde Kyosho 34427T1B Fazer MK2 Datsun 240Z 1971 Tuned Ver. ...
Kyosho 34427T1B Fazer MK2 Datsun 240Z 1971 Tuned Ver. ...
Now driving R/C is even more fun FZ02 chassis with realistic racing car body   For the pure enjoyment of R/C car driving, the combination of a beautifully reproduced car body with the FAZER series chassis can’t be beaten. Kyosho has taken its standard touring car chassis and given it a full model makeover that has evolved performance to a new level. A simplified design with fewer parts has improved maintenance efficiency and reduced weight while core strength and rigidity has been increased through new materials and ribbing and stiffeners on front and rear. In addition, the symmetrical chassis design synergizes excellent front-rear balance through the suspension with responsive control, irrespective of power source. Featuring slipper clutch, front & rear gear differentials, oil shocks and full ball bearing specs, the high durability and impact resistance allows drivers to unleash the full potential of the chassis. Brake disc wheel hubs with two different offsets (0mm, +5mm) provide compatibility with 190mm and 200mm width body styles and allows the wheelbase to be adjusted to 270mm by replacing some parts (sold separately) for compatibility with other 1/10 scale body styles, in addition the body included. The Readyset package comes fully assembled and includes everything except charger and battery for the chassis, and batteries for the transmitter.   ●“Ultra Scale Body” replicates the fine details of the actual body of the car. Kyosho took a step further in scale realism. ●Equipped with vintage touring car (VTC) tires and rostyle type wheels designed to match vintage cars. ●The separately sold LED light unit (97054) can be attached to the front and rear light buckets, making it even more scaled. ●Factory-assembled Readyset package only requires 4 x AA alkaline batteries for the transmitter, and battery with charger for the chassis. ●Full ball bearings that reduce drive loss equipped throughout the drive system. ●Features KS202W waterproof steering servo. ●Sealed differential and transmission deliver reliable performance, even on dusty parking lot surfaces. ●Shaft drive full-time 4WD touring chassis（FZ02）. ●Equipped with a plated dummy brake disc and a painted brake caliper to improve the sense of scale. ●Uses button screws with hexagonal holes in each part. Reliable tightening torque can be applied, and maintenance is possible with even fewer tools. ●Since the motor mount has mounting holes according to the pinion gear, troublesome backlash adjustment is unnecessary. Supports from 29T to 37T. ●Performance can be further enhanced by installing various optional parts. Completely realizes low center of gravity with its simple, functional design. Featuring an integrated gearbox that optimizes torsional rigidity of the main chassis, the nylon material reduces weight while improving impact resistance. Each key component has been reinforced in this simple design without upper deck. Features a reduced number and variety of screws and parts, and consolidation of frequently used screws into the same size. Most screws are flat head screws that can be removed with a 2.0mm hex wrench for easy disassembly. Handling factors such as bump steer and scrub radius are optimized on front suspension. Simple ball-connected steering knuckle promises reliable control movement. Interchangeable on both front and rear left-right hub carriers optimize spare parts utilization and improve maintenance efficiency. Includes choice of two offset brake disc wheel hubs with dummy calipers (for visual styling) that provide compatibility with 190mm and 200mm body widths. Equipped with an oil shocks as standard equipment. Change the vehicle height by changing the length of the damper end according to the vehicle type. Standard spur and pinion gear setting is 68T and 32T, but 9 pinion gear settings can be used from 29T – 37T to produce a wide range of gear ratio settings. The new fixed gear mesh motor mount has holes for use with each different pinion gears. Just simply mount the motor directly to the hole locations corresponding to the pinion gear. No gear mesh adjustment is necessary. Nissan’s sports car ‘Z’ is so pertly pretty it was released under the name ‘Fairlady’ in Japan. Known as the DATSUN Z in North America, this tuned version of the 1971 model lets its high performance and power shine with over fenders and spoilers on front and rear. Vintage Touring Car (VTC) tires & Rostyle type wheels to match vintage car style. Front and rear light buckets compatible with the separately sold 97054 LED light unit series. By installing the LED light unit, it transforms into a body full of real car feeling. Technical Data ■Length 462mm ■Width 200mm(Body width * Excluding mirrors) ■Height 136mm ■Chassis Height 8mm(approx.) ■Wheelbase 260mm ■Tread (F/R)  167mm ■Tires (F/R)  φ64×27.7mm ■Gear Ratio 6.54：1 ■Weight  1650g (approx.) ■R/C system &; Syncro KT-231P+ ■Motor G14L Kit Content ●Completed chassis with R/C radio installed ●Factory assembled body complete with color scheme ●Syncro KT-231P+ transmitter ●Hexagonal wrench ●Spanner ●Setting change parts Requirement to Run ●4 x AA batteries for transmitter ●Battery for chassis (recommended: 7.2V Ni-MH battery) ●Charger for battery for chassis ●Tools

3.795,-

3.995,-

Ikke på lager
Ikke på lager
-5%
Hovedbilde Traxxas 9136 Caster Blocks EHD (Pair) (for Upgrade Kit ...
Traxxas 9136 Caster Blocks EHD (Pair) (for Upgrade Kit ...
Traxxas 9136 - Caster blocks (c-hubs), extreme heavy duty, black (left & right)/ 3x26mm hinge pins (2)/ 3x15mm BCS (2) (for use with #9180 and 9181 upgrade kit) Replacement left and right caster blocks (c-hubs) for 9180 and 9181-series 2WD Extreme Heavy Duty Upgrade Kits. Includes 3x26 mm hinge pins (2) and 3x15 mm screws (2). Parts are compatible with non-EHD parts as well as Traxxas aluminum accessories.

99,-

På lager 2
KJØP
Hovedbilde Traxxas 9137 Steering Blocks EHD (Pair) (for Upgrade ...
Traxxas 9137 Steering Blocks EHD (Pair) (for Upgrade ...
Traxxas 9137 - Steering blocks, extreme heavy duty, black (left & right)/ 3x26mm hinge pins (2)/ 3x15mm BCS (2) (for use with #9180, 9181, 9182 upgrade kit) Replacement left and right steering blocks for 9180, 9181, and 9182-series 2WD Extreme Heavy Duty Upgrade Kits. Includes 3x26 mm hinge pins (2) and 3x15 mm screws (2). Parts are compatible with non-EHD parts as well as Traxxas aluminum accessories.

79,-

89,-

På lager 1
KJØP
-11%
Hovedbilde Mstyle M-002 R/C Set - Radioset, Servo, Battery and ... Hovedbilde Mstyle M-002 R/C Set - Radioset, Servo, Battery and ...
Mstyle M-002 R/C Set - Radioset, Servo, Battery and ...
Genial til Tamiyabiler! Radio og mottaker. NiMh batteri og USB lader. Servo 6kg Dette settet fra MStyle inneholder radio og mottaker, 6kg analog servo og et 7.2V 2000mAh NiMh-batteri og kompatibel lader. Denne pakken vil være genial for den som har et kit eller eldre bil liggene som trenger utstyr.   R/C Set - Radioset with Servo, Battery and Charger   The new R/C set from MStyle is the ultimate package for anyone looking to build or upgrade their R/C car with high-quality electronics. This all-in-one kit provides nearly everything you need to get your vehicle up and running, whether you"re a hobbyist or a seasoned R/C enthusiast.   What’s included in the set: Radio T-401 2.4GHz: A reliable, easy-to-use transmitter offering precise control for your R/C car. Receiver R-401 4Ch 2.4GHz (Waterproof): A durable and waterproof receiver designed to ensure stable connectivity in various conditions. Servo S-602W 6KG: A powerful and responsive servo with a 6kg torque capacity, perfect for handling sharp turns and quick movements. USB NiMh Charger C-U02: A convenient USB charger for recharging your battery quickly and efficiently. 7.2V 2000mAh NiMh Stick Pack (with Tamiya Plug): A high-performance battery that provides the power you need for extended driving sessions.   Whether you’re assembling a new car or upgrading your current one, this set is designed to simplify the process and deliver a premium R/C experience. Get ready to take your R/C car to the next level with MStyle!     Transmitter T-401 The MStyle T-401 4-Channel radio system uses the latest digital 2.4GHz radio technology to give you trouble-free, total control of your RC car. This is a fully featured, lightweight, 4-channel radio with advanced ergonomic features and total adjustability. Thanks to its crystal-free 2.4GHz technology, you will be able to confidently drive with your friends without worrying about things like frequencies or radio conflicts, and the waterproof R-401 receiver allows you to take your RC vehicle anywhere you can dream! The advanced features of the MStyle T-401 let you set the radio up for your car with custom settings like servo reversing, center trim, dual rate and end point adjustments. Only 4 AA batteries are required to power the MStyle T-401, so it"s light in your hands, and the foam steering wheel makes it comfortable to hold. With the built-in failsafe feature, you will be protected just in case the radio transmitter loses its connection with the receiver. MStyle T-401 Radio Features Digital 2.4GHz FHSS technology 4 Channel Digital on and off switch Foam-covered wheel for extra comfort and grip Servo end point adjustments for steering and throttle Servo reversing Steering dual rate Centre trim (steering and throttle) Audible warnings if you leave the MStyle T-401 switched on as well as battery life! Lightweight (only 4 AA batteries required)     Receiver R-401 The R-401 is the latest receiver for the MStyle T-401 transmitter. Simply bind and drive and have fun with your friends thanks to crystal-free 2.4GHz technology Its tiny size is just 35x26mm and only 17mm high, and its extremely light weight of just 13 grams means it won"t affect the weight balance, no matter where it"s installed. The R-401’s PCB features its own silicone jacket within the Hardcase outer for waterproof protection for a true go-anywhere RC experience, allowing you to drive in mud, rain, and snow! And with failsafe protection, you have peace of mind no matter what RC vehicle you drive! MStyle R-401 Receiver Features: Waterproof R-401 receiver works with MStyle T-401 transmitters Digital Frequency-Hopping Spread Spectrum (FHSS) 2.4GHz technology Simple radio binding steps Adjustable built-in Signal loss failsafe Run your RC models kit with other drivers without worrying about frequencies! 4-Channel A built-in light controller on a separate channel will allow for the addition of headlights and taillights on suitable models with the Maverick LED Light Set (#150465) or HPI Warm White LED Kit (#160560) Ideal for electric RC vehicles with a 6V 35mA minimum BEC power input     C-U02 USB Charger This USB Delta-Peak Charger is a simple and easy to use charger for 2-8 Cell NiMH battery packs. A USB Adaptor with an output of at least 2A is recommended. Specifications: 2-8 Cell NiMH (600-2500mAh) Charging range USB input 5V 1A, (2A Recommended) Delta-Peak Charging Tamiya Battery connector     S-602W Servo This water-resistant servo is ideal for bashers and racers looking for a tough and durable servo that can be used in wet conditions (e.g. rain, snow, puddles). Features: Operating Voltage: 4.8-6V 4.8V: Speed: 0.18 sec/60 degrees, Torque: 6kg-cm 6V: Speed: 0.16 sec/60 degrees, Torque: 7kg-cm Servo Spline: 25T Dimensions: Main case: 40x37.5x20.0mm (excluding mounting tabs, servo spline, & cable outlet) Mounting tab hole centres: 49.5.0x10mm Weight: 46g (excluding servo horn)

795,-

895,-

På lager 3
KJØP
-11%
Hovedbilde Mstyle M-002 R/C Set - Radioset with Servo Hovedbilde Mstyle M-002 R/C Set - Radioset with Servo
Mstyle M-002 R/C Set - Radioset with Servo
Genial til Tamiyabiler! Radio og mottaker. Servo 6kg Dette settet fra MStyle inneholder radio og mottaker og 6kg analog servo. Denne pakken vil være genial for den som har et kit eller eldre bil liggene som trenger utstyr.   R/C Set - Radioset with Servo.   The new R/C set from MStyle is the ultimate package for anyone looking to build or upgrade their R/C car with high-quality electronics. This all-in-one kit provides nearly everything you need to get your vehicle up and running, whether you"re a hobbyist or a seasoned R/C enthusiast.   What’s included in the set: Radio T-401 2.4GHz: A reliable, easy-to-use transmitter offering precise control for your R/C car. Receiver R-401 4Ch 2.4GHz (Waterproof): A durable and waterproof receiver designed to ensure stable connectivity in various conditions. Servo S-602W 6KG: A powerful and responsive servo with a 6kg torque capacity, perfect for handling sharp turns and quick movements.   Whether you’re assembling a new car or upgrading your current one, this set is designed to simplify the process and deliver a premium R/C experience. Get ready to take your R/C car to the next level with MStyle!     Transmitter T-401 The MStyle T-401 4-Channel radio system uses the latest digital 2.4GHz radio technology to give you trouble-free, total control of your RC car. This is a fully featured, lightweight, 4-channel radio with advanced ergonomic features and total adjustability. Thanks to its crystal-free 2.4GHz technology, you will be able to confidently drive with your friends without worrying about things like frequencies or radio conflicts, and the waterproof R-401 receiver allows you to take your RC vehicle anywhere you can dream! The advanced features of the MStyle T-401 let you set the radio up for your car with custom settings like servo reversing, center trim, dual rate and end point adjustments. Only 4 AA batteries are required to power the MStyle T-401, so it"s light in your hands, and the foam steering wheel makes it comfortable to hold. With the built-in failsafe feature, you will be protected just in case the radio transmitter loses its connection with the receiver. MStyle T-401 Radio Features Digital 2.4GHz FHSS technology 4 Channel Digital on and off switch Foam-covered wheel for extra comfort and grip Servo end point adjustments for steering and throttle Servo reversing Steering dual rate Centre trim (steering and throttle) Audible warnings if you leave the MStyle T-401 switched on as well as battery life! Lightweight (only 4 AA batteries required)     Receiver R-401 The R-401 is the latest receiver for the MStyle T-401 transmitter. Simply bind and drive and have fun with your friends thanks to crystal-free 2.4GHz technology Its tiny size is just 35x26mm and only 17mm high, and its extremely light weight of just 13 grams means it won"t affect the weight balance, no matter where it"s installed. The R-401’s PCB features its own silicone jacket within the Hardcase outer for waterproof protection for a true go-anywhere RC experience, allowing you to drive in mud, rain, and snow! And with failsafe protection, you have peace of mind no matter what RC vehicle you drive! MStyle R-401 Receiver Features: Waterproof R-401 receiver works with MStyle T-401 transmitters Digital Frequency-Hopping Spread Spectrum (FHSS) 2.4GHz technology Simple radio binding steps Adjustable built-in Signal loss failsafe Run your RC models kit with other drivers without worrying about frequencies! 4-Channel A built-in light controller on a separate channel will allow for the addition of headlights and taillights on suitable models with the Maverick LED Light Set (#150465) or HPI Warm White LED Kit (#160560) Ideal for electric RC vehicles with a 6V 35mA minimum BEC power input       S-602W Servo This water-resistant servo is ideal for bashers and racers looking for a tough and durable servo that can be used in wet conditions (e.g. rain, snow, puddles). Features: Operating Voltage: 4.8-6V 4.8V: Speed: 0.18 sec/60 degrees, Torque: 6kg-cm 6V: Speed: 0.16 sec/60 degrees, Torque: 7kg-cm Servo Spline: 25T Dimensions: Main case: 40x37.5x20.0mm (excluding mounting tabs, servo spline, & cable outlet) Mounting tab hole centres: 49.5.0x10mm Weight: 46g (excluding servo horn)

679,-

719,-

På lager 5
KJØP
-6%
Hovedbilde Bronto Overgang - Female Traxxas til Male Deans
Bronto Overgang - Female Traxxas til Male Deans
Overgang fra Traxxas female til male Deans (T-Plugg). Bronto RC tilbehør er et must for å komplettere din RC hobby. Kvalitetstilbehør og komponenter perfekt for dine prosjekter.

59,-

På lager 3
KJØP
Hovedbilde Tamiya 47520 M-07R Chassis Kit Hovedbilde Tamiya 47520 M-07R Chassis Kit
Tamiya 47520 M-07R Chassis Kit
Dette FWD-chassisettet tar det revolusjonerende M-07-konseptet og fyller esken med en rekke tilleggsdeler, valgt av Tamiya Racing Factory (TRF)-teamet for et racingoppsett. Dette er rett og slett mye for pengene, for de som ønsker å komme rett inn i racing, eller oppnå en race spec’et bil uten å måtte velge masse Hop-Up-alternativer og reservedeler selv. M-07 er et fantastisk chassis, og gir deg enorm kjøreglede. M-07 chassiset kan valgfritt monteres  med 225mm (M) eller 239mm (L) hjulbase. Må kompletteres med: Radio og mottaker Servo (low profile) Fartskontroller Motor (540 størrelse) NiMH eller LiPO batteri Egnet batterilader Karosseri (M-chassis) PS lakk Mere info på engelsk:     ★Left: Long arms and steering linkage components optimize damper leverage ratio. The chassis’ camber can also be adjusted.★Right: Adjust the M-07 Concept’s rear toe angle via the insertion of spacers where the suspension mount parts are attached.       ★Left: One of the key points is the easy-access differential unit, which can be removed and changed from the underside.★Right: Enjoy silky-smooth power from your chassis thanks to full ball bearings, universal drive shafts and gear differential unit.   Specifications ●Length: 332mm (including bumper) ●Width: 164mm ●Wheelbase: 225mm or 239mm (Selectable) ●Monocoque Frame ●Front-Midship Motor, Front-Wheel Drive ●Gear Differential ●3-Piece Steering Tie-Rod ●4-Wheel Independent Double Wishbone Suspension ●CVA Oil Dampers ●Gear Ratio = 5.78:1 using included 20T pinion gear (7.22:1 – 4.81:1 available with separately sold pinion gears) ●Requires an Electronic Speed Controller (sold separately) This R/C FWD chassis kit takes the revolutionary M-07 Concept and pairs it with a range of option parts, selected by the Tamiya Racing Factory (TRF) team for a racing setup. This is a great value-for-money option for those who want to get straight into racing, or achieve a race-spec car without having to select Hop-Up Option and Spare parts themselves. Featured Components • M-07 Concept High-Traction Lower Deck (54812) • TRF Special Damper (Hard Black Coating) (42102) • M-07 Concept Reinforced C Parts (Uprights) 2pcs. (54810) • M-07 Concept Reinforced D Parts (Suspension Arms) 2pcs. (54811) • 33mm Double Cardan Joint Shaft (2pcs.) (42312) • Clamp Type Aluminum Wheel Hub (5mm Thick) (53823) • Rear Stabilizer • Aluminum Cup Joint for TA06 Gear Differential Unit (2pcs.) (54532) • Hard Fluorine Coated 0.6 Aluminum Pinion Gear (20T) (53509) • φ2.6mm Titanium Coated Suspension Shaft Set for Reversible Suspension (53917) • 46mm Titanium Coated Suspension Shafts 2pcs. (53851) • 3x106mm Aluminum Turnbuckle Shaft (54756) • 1/10 scale R/C chassis assembly kit. Length: 332mm. • Includes dedicated carbon fiber battery holders unique to this kit. • The chassis has superb rigidity thanks to reinforced upright and suspension components, as well as a high- traction lower deck. • A highly efficient drivetrain employs 33mm double cardan joint shafts and aluminum joint cups, plus a durable fluorine coated aluminum 20T pinion gear. • Highly agile suspension utilizes TRF Special Dampers, rear stabilizer and titanium coated suspension shafts. • Also included are aluminum hex hubs and 3x106mm turnbuckle shaft. • Requires: 2-Channel Radio, servo, motor, ESC, 7.2-7.4volt battery pack & compatible charger, m-chassis body set, and Tamiya PS paint.

3.895,-

4.295,-

På lager 3
KJØP
-9%
Hovedbilde Savox SV-0258MG Servo 8Kg 0,11s HV Metal Gear Low ... Hovedbilde Savox SV-0258MG Servo 8Kg 0,11s HV Metal Gear Low ...
Savox SV-0258MG Servo 8Kg 0,11s HV Metal Gear Low ...
SAVÖX SAV-SV0258MG - SV-0258MG Low Profile Servo 8Kg 0.11s HV Hybrid Gears Protection and Precision for Entry-Level RC The SV-0258MG is engineered to work seamlessly with entry-level ESCs in RTR kits, limiting current draw to just 1.5A to prevent shutdowns and ensure uninterrupted driving. Its low-profile composite case saves space, while hybrid gears and digital electronics provide consistent, precise steering control. It's ideal for RTR and 1/10 touring cars where both protection and performance matter. Hybrid Metal/Composite Gears Provides a balance of durability and weight savings for everyday and beginner use. Low-Profile Compact Size Measures only 40.8×20.2×27.75mm, making it a perfect fit for 1/10 touring cars and other compact builds. Digital Precision Control Equipped with a 10-bit digital PCB and VR potentiometer for smooth, accurate steering response. Specs: Line: BLACK EDITION Application: CAR Servo Size: Low Profile Operating Voltage: 6V-7.4V Speed @6.0V: 0.13s/60° Torque @6.0V: 6.5kg/cm Speed @7.4V: 0.11s/60° Torque @7.4V: 8.0kg/cm Amplifier Type: Digital Controller Motor Type: DC Case Type: Composite Protection: Dust Resistant Dimensions: L40.8xW20.2xH27.7 mm Weight: 36g Gear Type: Hybrid (Metal/Composite) Compatibility: Sanwa SSR PCB Board: 10-bit Horn Gear Spline: 25T (Φ6) Rotating Direction: Clockwise (when 1000→2000μsec) Max Travel: ~140° (when 800→2200μsec) Operating Travel: 90° (when 1000→2000μsec) Neutral Position: 1500μsec Bearing: 2x Ball Bearings Potentiometer: VR Cable Diameter: 26AWG Cable Length: 250±5mm Connector: JR Stall Current @6.0V: 1500mA Operating Current @6.0V: 150mA Stall Current @7.4V: 1800mA Operating Current @7.4V: 180mA Idle Current: 6mA Dead Band Width: 3-5μsec Frequency Range: 50-360Hz Control System: Pulse Width Modification Operating Temperature: -10°C to 50°C

379,-

399,-

** Ikke på lager
KJØP
-5%
Hovedbilde Power HD LW-15MG Waterproof Servo 15kg/0.11s Hovedbilde Power HD LW-15MG Waterproof Servo 15kg/0.11s
Power HD LW-15MG Waterproof Servo 15kg/0.11s
Power HD servo perfekt til deg som ønsker å oppgradere fra din orginalservo. Flott og motstandsdyktig utførelse i aluminiums-hus med gir i kobber og aluminium. Servoen er vannbestandig og div servohorn og skruer medfølger. Flott servo til 1/10 offroadbiler. Spesifikasjoner: Kraft 4.8V: 10kg/cm Hastighet 4.8V: 0.15s Kraft 6.0V: 12.5kg/cm Hastighet 6.0V: 0.13s Kraft 7.2V: 15kg/cm Hastighet 7.2V: 0.11s Vekt: 62g Gir: Kobber & Alu Størrelse: 40.5x 20.5 x 39.3mm Servohorn 25T

449,-

499,-

På lager 1
KJØP
-10%
Hovedbilde Tamiya 86021 PS-21 Polycarbonate Spray Park Green 3 oz
Tamiya 86021 PS-21 Polycarbonate Spray Park Green 3 oz
 This is Tamiya Color Spray Lacquer for Polycarbonate (PS-21 Park Green).                           For Adult Modelers Only. FEATURES: Specially developed for decorating transparent polycarbonate bodies             used in R/C car modeling.           An appropriate amount of paint for finishing one R/C model.           This paint is impervious to oil and fuels, so they can be safely             used on gas-powered R/C bodies.           The color of the lid represents the color of paint. INCLUDES: (1) Spray Can of Lacquer SPECS:    Net Volume: 100ml COMMENTS: Never use this paint on plastic models.           Highly flammable.

109,-

På lager 8
KJØP
Hovedbilde Traxxas 3743 Steering Bellcrank
Traxxas 3743 Steering Bellcrank
These are Steering Bellcranks and Draglinks for the                       Traxxas Rustler and Stampede. FEATURES: White Plastic Construction INCLUDES: One Bellcrank           One Link           One Arm REQUIRES: Rustler of Stampede COMMENTS: None  

49,-

På lager 1
KJØP
Hovedbilde Traxxas 3631 Suspension Arms Front (2)
Traxxas 3631 Suspension Arms Front (2)
This is the Traxxas replacement #3631 Front Suspension Arms for for the Stampede and Rustler. FEATURES:    Made from black molded nylon    For the Traxxas Stampede and Rustler. SPECS:    Length: 3 1/4"    Thickness: 3/8"    Width at end near chassis: 1 1/2"    Width at end near wheels: 7/8" INCLUDES:    (2) Front suspension arms for the Traxxas Stampede.

99,-

På lager 3
KJØP
Hovedbilde Traxxas 2577 Button Head Screw 3x10mm Revo (6)
Traxxas 2577 Button Head Screw 3x10mm Revo (6)
This is a Package of Six 3mm x 10mm Button Head Screws. FEATURES: Metal Construction           Black in Color           Button Head Type           Machine Thread INCLUDES: Six 3mm x 10mm Button Head Machine Thread Screws REQUIRES: Nothing.

35,-

På lager 3
KJØP
Hovedbilde Traxxas 4690 Spur Gear 48P 90T
Traxxas 4690 Spur Gear 48P 90T
This is a Traxxas 48P, 90T Spur Gear for models                        with Torque Control Slipper Clutch. FEATURES: 48 pitch           90 tooth           Designed for models with a slipper clutch           Black plastic construction INCLUDES: One spur gear SPECS:    Pitch:   48           Tooth:   90

49,-

På lager 8
KJØP

SamiRC Norge AS

© 2026 SamiRC Norge AS - Powered by Mystore.no

Om oss

  • SamiRC Norge AS
  • Nils Lauritssøns vei 34
  • 0870 OSLO
  • Org. nr. MVA 928 644 979 Foretaksregisteret
  • Tlf: 46760019
  • post@samirc.no

Kundeservice

Nyhetsbrev

  • klarna-dark.png
  • vipps-orange.png
  • mastercard-full.png
  • visa.png
  • paypal.png