Hopp til innhold

Traxxas 5650 Half Shafts E-Revo

Art.nr: TRX 5650

75,-

Traxxas

Traxxas

På lager: 5

På lager i vår butikk i Oslo

Produktet er midlertidig utsolgt. Dersom du ønsker å motta en epost når vi får det inn på lager, kan du legge igjen epostadressen din i skjemaet under.

Informasjon

This is the Center Half Shaft Set for the Traxxas E-Revo and E-Maxx

FEATURES: Plastic construction, black in color


INCLUDES: Center half shafts (three internal splined and two external splined)


REQUIRES: Installation on the vehicle


SPECS:    Diameter: 17.2mm (0.68")

Produsent

Dette er den beste merket for RC-BIL i hele Norge, nei vi kan vel si hele verden uten å trenge å være redd for at vi sier noe galt!

Kunder kjøpte også

This is a Traxxas 4X12mm Button Head Screw Set. FEATURES: Steel construction           Black in color           Low-profile, button-head design           Hex drive (allen type) INCLUDES: Six Screws REQUIRES: Assembly to vehicle SPECS:    Overall Length:  12mm (.63")           Threaded Length: 11mm (.45")           Thread Size:     M4x.7mm coarse           Hex Wrench Size  2.5mm COMMENTS: Used on the Revo to mount the transmission skid plate.

35,-

Ikke på lager
Ikke på lager
These are replacement motor screws and washers for any 05 size motor. Features: 6 3x8mm socket head screws           6 3mm washers           1 Hex allen wrench

39,-

På lager 4
KJØP
Long life, high discharge rate suitable for RC use Alkaline standard batteries for use with radio transmitters or any device that requires AA batteries. Perfect for all HPI RTR kits! Also available are rechargeable AA batteries! #101938 HPI Plazma 1.2V 2700mAh Nimh AA Re-Chargeable Battery (4Pcs)

29,-

På lager 31
KJØP
Traxxas 5452X - U-Joints Set U-joints, driveshaft (carrier (4)/ 4.5mm cross pin (4)/ 3mm headed pin (4)/ 4x15mm screw pin (2)/ hex pin (2)/ e-clips (6)/ 3x6x0.5 MW (4)) (metal parts for 2 driveshafts) Driveshaft U-joint rebuild kit. Includes carriers (4), cross pins (4), headed pins (4) screw pins (2), hex pins (2), and E-clips (6). Rebuilds 2 driveshafts. Replacement part for these models: Ford® Fiesta® ST Rally Brushless Maxx® Rustler® 4X4 Brushless Slash® 4X4 Brushless Stampede® 4X4 Brushless

129,-

139,-

På lager 2
KJØP
-7%
Traxxas 5351A - T-Maxx® Torque Control Slipper Upgrade Kit (fits first generation T-Maxx® transmission, w/o Optidrive®) (patent pending)   The Torque-Control slipper clutch upgrade kit fits T-Maxx®Classic, S-Maxx®, and SportMaxx® trucks equipped with the original T-Maxx style black transmission. It features efficient semi-metallic friction pads and allows for spur gear replacement without altering the slipper clutch setting. Kit includes everything needed for the conversion, along with complete instructions and parts exploded views.

289,-

På lager 4
KJØP
Ball bearings, black rubber sealed (12x18x4mm) (2)

109,-

På lager 5
KJØP
This is the Stock Replacement Bumber Mount Set for the Traxxas T/E Maxx trucks.              These mounts attach the bumpers to the bulkheads. FEATURES: Black nylon construction INCLUDES: One L&R Front Bumper Mount Set           One L&R Rear Bumper Mount Set           Eight 3x15mm round head machine screws REQUIRES: Nothing.  This is a direct replacement part.

49,-

På lager 1
KJØP
Tubular Front Bumper for the Traxxas T-Maxx & E-Maxx Quick Notes: – replaces stock Traxxas #3926, #4935 & #4935X – matching Heavy Duty Rear Bumper also available Description RPM bumpers are not only the strongest bumpers made; they are extremely lightweight and have a scale, realistic appearance. Our front bumper adds extra protection with a lower, tubular bar extending down to help absorb impacts that would have been taken by the front skid plate alone. We’ve also strengthened the areas around the screw holes. Our rear bumpers have the scale appearance of a step bumper found on most full-sized trucks. Our rear bumper weighs the same as a stock bumper, yet is stronger, and supports the rear skid plate for added rear-end protection. In addition, we’ve designed a recessed area where you, with a little creativity, can add in a customized, scale license plate or a ball hitch! All colored bumpers have the color molded in, not dyed, for long lasting color, even when scratched. Our “Chrome” finish bumpers are coated over our silver bumper to help prevent nicks and scratches from showing through.   ​​​​​​​

149,-

På lager 1
KJØP
1/2-OFFSET - 4WD FRONT & REAR Fits: Traxxas SUMMIT Front & Rear HPI SAVAGE FLUX HP Front & Rear HPI SAVAGE XL Front & Rear HPI SAVAGE X 4.6 Front & Rear Kyosho Mad Force Kruiser 4WD Front & Rear Kyosho FO-XX VE 4WD Front & Rear Kyosho FO-XX GP 4WD Front & Rear Also fits other 1/8 Scale Monster Trucks with 17 mm hex Also fit these Traxxas Trucks if converted with 17 mm hexes - 425353X, 425353G & 425353R: Traxxas E-REVO Front & Rear TRX56036-1 Traxxas E-REVO Front & Rear TRX56036-4 Also fit these Trucks if you want a wider stance (width): Traxxas E-Maxx Front & Rear (if converting to 17 mm hexes) Traxxas E-Maxx Brushless Front & Rear Traxxas E-REVO Front & Rear (if converting to 17 mm hexes) Traxxas E-REVO Brushless Front & Rear Traxxas REVO 3.3 Front & Rear Traxxas T-Maxx 3.3 Front & Rear (if converting to 17 mm hexes) Arrma Kraton Front & Rear Arrma Talion Front & Rear Arrma Nero Front & Rear Specs: Wheel diameter: 3.8" Tire Diameter: 168 mm Tire Width: 106 mm Weight (each): 467 g Hex: 17 mm Offset: 1/2" Tire Compound: Sport Wheel finish: Black Nylon

549,-

599,-

** Ikke på lager
KJØP
-8%
This is a pair of replacement Wheel Hex Hubs for the                            Traxxas E-Maxx. FEATURES: Steel construction, black in color           Replaces worn or damaged hexes INCLUDES: Two Wheel Hub Hexes           Two 2.5x12mm Axle Pins REQUIRES: Installation SPECS:    Hex Size: 14mm           Thickness: 6mm

39,-

På lager 4
KJØP
Mottaker til FlySky Noble FS-NB4 PL18. Egner seg godt til radiostyrt bil og båt.   Informasjon på engelsk: 2.4GHz 4 channel receiver is compatible with FlySky Noble FS-NB4 PL18 Transmitter, good for Rc Car and Rc Boat. FGr4S adopts AFHDS 3, Flysky’s third-generation automatic frequency hopping digital system. Easy to bind and very fast link-up, quick and extremely stable in performance. It uses an internal single antenna with two-way transmission capabilities and is designed to be compact and easy to install. The receiver supports PPM/i-bus/PWM data output, suitable for AFHDS3 system remote controller.   Fra produsenten: Product Model: FGr4S PWM channel: 4 Wireless frequency: 2.4GHz Wireless protocol: AFHDS 3 Range:> 200m (ground) Antenna type: Built-in single antenna Power: 3.5-8.4V RSSI: Supported Data port: PWM / PPM / i.bus / s.bus Temperature range: -10 ℃ — + 60 ℃ Humidity range: 20% -95% Online Update: Yes Dimensions: 25.5 * 22 * 17.3 mm Weight: 5.1g Certification: CE, MIC, RCM, FCC ID: N4ZFGRS400   Package List: 1 * FGr4S Receiver 1 * Binding Cable Binding: To ensure good signal strength, make sure the receiver antenna is as far away from any metal parts when installing the receiver. 1. Insert the binding cable into the receiver’s BIND port. 2. Plug the power cable into any other port, and the receiver’s LED will start to flash quickly indicating that it has entered bind mode. 3. Put the transmitter into bind mode; (See the transmitter’s instruction manual for more information.) 4. Binding is successful when the receiver’s LED starts to flash slowly. Remove the power and bind cables from the receiver *if the transmitter is bidirectional the reciever status indicator will not fash slowly. 5. Reconnect the power cable to the receiver. 6. Check to make sure that the transmitter and receiver are working as expected, if there are any issues or unexpected operation follow the steps above to bind again.

595,-

695,-

På lager 6
KJØP
-14%
These are 4mm Locking Nuts from Traxxas. FEATURES: Stainless steel construction.           Nylon insert. INCLUDES: 10 Lock Nuts SPECS:    Size:  4mm                       

30,-

På lager 9
KJØP
This is a package of six 3x15mm Traxxas Countersunk Hex Head Screws. FEATURES: Steel construction, Black in color           Used on the Traxxas Revo monster truck, can also be used in any             application where a 3x15mm countersunk screw is required INCLUDES: Six 3x15mm Traxxas Countersunk Hex Screws REQUIRES: 2mm hex head wrench. SPECS:    Length:  15mm           Diameter: 3mm

35,-

På lager 1
KJØP
Louise ST-SPIDER Stadium Truck Soft Tires on 2.2" Black Wheels Stadium Truck tires mounted on 2.2" black wheels that is a perfect upgrade for your Traxxas 1/16 E-REVO or 1/16 Summit. Fits: Traxxas 1/16 E-REVO Front & Rear Traxxas 1/16 SUMMIT Front & Rear HPI Savage XS Flux Front & Rear 1/10 Scale Buggies Rear Specs: Wheel diameter: 2.2" Tire Diameter: 90 mm Tire Width: 42.5 mm Weight (each): 81 g Hex: 12 mm Tire Compound: Soft Wheel finish: Black Nylon Original Traxxas 1/16 E-REVO Tire info: Diameter: 82 mm Width: 46 mm Total Track Width: 240 mm Traxxas 1/16 E-REVO with Louise ST-Spider 2.2" Truck Tires: Total Track Width: 260 mm (+10 mm off-set per wheel) 8 mm larger diameter: you may need adjust the vehicle gearing to not overload the motor/esc The added off-set may put more load on the steering servo

269,-

289,-

** Ikke på lager
KJØP
-7%
2S 5300mAh -100C - Sunpadow ERC LiPo Sunpadow 2s 5300mAh 100C. Kraftig hardcase LiPopakke med meget høy C-rating. Passer utmerket til både on- og off-road samt crawling. Batteriet leveres i egen oppbevaringseske. Leveres uten lade/drift-kabel.   Spesifikasjoner: Kapasitet: 5300mAh Spenning: 2S 7.4V C-Rating 100C Anbefalt ladestyrke:     1C Vekt: 270gram Størrelse: 139x47x25.1mm Kontakt: 4mm gull

399,-

419,-

** Ikke på lager
KJØP
-5%
This is a package of six 3x12mm Traxxas Countersunk Hex Head Screws. FEATURES: Steel construction, Black in color           Used on the Traxxas Revo monster truck, can also be used in any             application where a 3x12mm countersunk screw is required INCLUDES: Six 3x12mm Traxxas Countersunk Hex Screws REQUIRES: 2mm hex head wrench. SPECS:    Length:  12mm           Diameter: 3mm

35,-

På lager 1
KJØP
This is a Traxxas 18 Tooth Pinion Gear for a 5mm Motor Shaft. FEATURES: Silver in color           Metal construction INCLUDES: (1) 18 Tooth Pinion Gear           (1) One 4mmx3.5mm set screw REQUIRES: Installation on motor shaft SPECS:    Outer Diameter: 15.5mm (0.61")           Inner Diameter: 5mm (0.20") Pitch 32P

69,-

79,-

På lager 3
KJØP
-13%
These are the Front or Rear Driveshaft Assemblies for the LaTrax Teton Monster Truck from Traxxas. FEATURES Composite plastic construction Transfers power from differentials to wheels INCLUDES Two Front or Rear Driveshaft Assemblies

65,-

På lager 5
KJØP
Yeah Racing Aluminum Drive Hex Wrench Set (1.5/2.0/2.5/3.0mm Hard Steel Allen Wrench) Black/Gold Description: With an anti-slip design handle and tips with an improved material for the tips these sleek black tools with a gold trim will sure be the best tools for you to keep in your pitbox! This set comes with the most used four sizes, so you can buy this set not having to worry not having the right tool! Feature: For: Car Building Material: Aluminum Color: Black/Gold Include: Allen Drivers (4 pcs)

349,-

399,-

** Ikke på lager
KJØP
-13%
Speed Bit Master Set Hex Driver (7-pieces) Traxxas 7-Piece Metric Hex Bit Master Set 7-Piece Metric Hex Bit Master Set (#8711) Features: Precision-ground, hardened steel metric hex drivers Rubber overmolded handle for superior grip and comfort Precise fit magnetic insert holds the speed bit in the handle Standard 1/4 inch hex shank for use with power drill drivers Heavy-duty pouch holds tools securely Custom embroidered Traxxas logo Clearly marked with laser etched sizes Includes: Straight hex drivers: 1.5 mm, 2 mm, 2.5 mm, 3 mm Ball end drivers: 2 mm, 2.5 mm, 3 mm Maximum Durability 7-Piece Metric Hex Bit Master SetTraxxas premium tool kits are manufactured from exceptionally high quality materials to provide years of pro-level service. The thoughtfully engineered grip features an overmolded rubber design for more power and excellent comfort. The precision-ground, hardened-steel hex tips fit just right, to prevent wear, rounding, and screw damage. Designed specifically for Traxxas models, these speed bit sets come in a tough, compact pouch making them ideal to take along for service in the field. The included rubber overmolded handle holds the bits securely with a powerful magnet for fast bit changes. Headed to the track? Don’t worry, the included heavy-duty tool pouch keeps everything secure for traveling. Pick up any of the Premium Metric Speed Bit Sets and get wrenching with the only tools guaranteed to be Traxxas Tough™.  

949,-

999,-

På lager 2
KJØP
-5%
This is the Short RPM Sensor for the                    XO-1 On-Road Car from Traxxas. FEATURES: Functions with the Traxxas Link system to display motor RPM INCLUDES: Short RPM Sensor with Zip Tie, 3x4mm Button Head Cap Screw and             3x4mm Set Screw SPECS:    Length: 7.5" (190mm)

139,-

159,-

På lager 3
KJØP
-13%
   This is the Retainer Clip for the Traxxas E-Revo. FEATURES: Nylon construction           Black in color INCLUDES: Battery Retainer Clip           Front Clip           Rear Clip           Foam Spacer           Instruction sheet REQUIRES: Installation on the battery compartment

39,-

På lager 2
KJØP
This is a Package of Replacement Caster Spacers for the Traxxas.                   These spacers adjust caster of the wheels. FEATURES: Black nylon construction. INCLUDES: Four caster spacers           Four caster shims REQUIRES: Nothing.  These are direct replacement parts. SPECS:    Thickness: 2mm (0.08")

39,-

På lager 2
KJØP
This is the Differential Gear Set for use on the                  Traxxas 1/16 E-Revo, Summit, Rally and Slash VXL Vehicles. FEATURES: Steel construction INCLUDES: Two Output Gears           Three Spider Gears           Two Differential Output Shafts           Three 1.5x6mm Pins           Two 1.5x8mm Pins REQUIRES: Installation on the vehicle

129,-

På lager 4
KJØP
These are the Front and Rear Differential Cover Plates          for use on the Traxxas 1/16 E-Revo, Summit, Rally and Slash VXL Vehicles. FEATURES: Nylon construction           Black in color INCLUDES: One Front and One Rear Diff Cover Plate           Two O-Rings           Two Gaskets           Three 2x14mm Button Head Screws REQUIRES: Installation on the vehicle

39,-

Ikke på lager
Ikke på lager
  • klarna-dark.png
  • vipps-orange.png
  • mastercard-full.png
  • visa.png
  • paypal.png