Traxxas

Stampede VXL

Populært i denne kategorien

Hovedbilde RPM 80185 Rear Suspension Arms for Rustler & Stampede ...

RPM 80185 Rear Suspension Arms for Rustler & Stampede ...

Art.nr: 80185

Copied

RPM Rear Suspension Arms for Rustler & Stampede (2WD) - Blue Replaces stock Traxxas #3655 & 3655X Quick Notes: Fits 2WD versions of the electric Stampede & Rustler Each A-arm is 7 grams lighter than stock! Eliminates over 0.03” (0.8mm) of slop from the inner arm mount Replaces stock Traxxas #3655 & 3655X RPM rear A-arms for the electric versions of the Traxxas Rustler & Stampede are stronger and more durable than stock versions, yet we’ve also managed to eliminate over 7 grams of weight per arm! That’s 14 grams of unsprung weight eliminated with a single pair of rear RPM A-arms! Coupled with a set of RPM front A-arms, the total weight loss exceeds 24 grams, or almost a full ounce! We accomplished this without creating any weak points nor are our A-arms any more flexible than the stock versions. Additionally, we’ve adjusted the shock mount locations slightly to allow more noticeable tuning adjustments when using the inner or outer shock mount holes (while the center hole remains in its stock location). While we were at it, we eliminated over 0.030” or 1/32” of slop from the inner arm mount and more than 0.010” or slightly less than 1/64” of slop at the outer hinge pin for an ultra-smooth, slop-free suspension system. RPM A-arms for the electric versions of the Traxxas Rustler & Stampede are molded in black, blue, green or red and are sold in pairs – 1 left rear and 1 right rear per package.

149,-

169,-

-12%

Hovedbilde RPM 80187 RPM Rear Suspension Arms for Rustler & ...

RPM 80187 RPM Rear Suspension Arms for Rustler & ...

Art.nr: 80187

Copied

RPM Rear Suspension Arms for Rustler & Stampede (2WD) - Pink Replaces stock Traxxas #3655 & 3655X Quick Notes: Fits 2WD versions of the electric Stampede & Rustler Each A-arm is 7 grams lighter than stock! Eliminates over 0.03” (0.8mm) of slop from the inner arm mount Replaces stock Traxxas #3655 & 3655X RPM rear A-arms for the electric versions of the Traxxas Rustler & Stampede are stronger and more durable than stock versions, yet we’ve also managed to eliminate over 7 grams of weight per arm! That’s 14 grams of unsprung weight eliminated with a single pair of rear RPM A-arms! Coupled with a set of RPM front A-arms, the total weight loss exceeds 24 grams, or almost a full ounce! We accomplished this without creating any weak points nor are our A-arms any more flexible than the stock versions. Additionally, we’ve adjusted the shock mount locations slightly to allow more noticeable tuning adjustments when using the inner or outer shock mount holes (while the center hole remains in its stock location). While we were at it, we eliminated over 0.030” or 1/32” of slop from the inner arm mount and more than 0.010” or slightly less than 1/64” of slop at the outer hinge pin for an ultra-smooth, slop-free suspension system. RPM A-arms for the electric versions of the Traxxas Rustler & Stampede are molded in black, blue, green or red and are sold in pairs – 1 left rear and 1 right rear per package.

149,-

169,-

-12%

Hovedbilde RPM 80189 Rear A-Arms Rustler/Stampede 2WD Red ...

RPM 80189 Rear A-Arms Rustler/Stampede 2WD Red ...

Art.nr: 80189

Copied

RPM Rear Suspension Arms for Rustler & Stampede (2WD) - Red Replaces stock Traxxas #3655 & 3655X Quick Notes: Fits 2WD versions of the electric Stampede & Rustler Each A-arm is 7 grams lighter than stock! Eliminates over 0.03” (0.8mm) of slop from the inner arm mount Replaces stock Traxxas #3655 & 3655X RPM rear A-arms for the electric versions of the Traxxas Rustler & Stampede are stronger and more durable than stock versions, yet we’ve also managed to eliminate over 7 grams of weight per arm! That’s 14 grams of unsprung weight eliminated with a single pair of rear RPM A-arms! Coupled with a set of RPM front A-arms, the total weight loss exceeds 24 grams, or almost a full ounce! We accomplished this without creating any weak points nor are our A-arms any more flexible than the stock versions. Additionally, we’ve adjusted the shock mount locations slightly to allow more noticeable tuning adjustments when using the inner or outer shock mount holes (while the center hole remains in its stock location). While we were at it, we eliminated over 0.030” or 1/32” of slop from the inner arm mount and more than 0.010” or slightly less than 1/64” of slop at the outer hinge pin for an ultra-smooth, slop-free suspension system. RPM A-arms for the electric versions of the Traxxas Rustler & Stampede are molded in black, blue, green or red and are sold in pairs – 1 left rear and 1 right rear per package.

149,-

169,-

-12%

Hovedbilde RPM 80242 Front A-Arms Black Rustler/Stampede/Slash ...

Hovedbilde RPM 80242 Front A-Arms Black Rustler/Stampede/Slash ...

RPM 80242 Front A-Arms Black Rustler/Stampede/Slash ...

Art.nr: 80242

Copied

RPM Front Arms for the 2WD: Slash, Nitro Slash, Rustler & Stampede - Black Replaces stock Traxxas #3631 Quick Notes: Fits all versions of the Traxxas 2WD: Slash, Nitro Slash, Stampede & Rustler Nearly 25% lighter than stock Replaces stock Traxxas #3631 RPM front A-arms for the Traxxas Slash 2wd, Nitro Slash, e-Rustler & e-Stampede 2wd are built to withstand some of the toughest abuse. Incredibly, we were able to shave some unwanted unsprung weight as well. RPM Front A-arms are nearly 25% lighter than stock versions of the same A-arms, yet the RPM versions are backed with our world-renowned breakage warranty. Additionally, we’ve increased clearance areas in the outer portion of the A-arms to allow increased droop travel when used in conjunction with RPM oversized bearing carriers (RPM #80372 & #80382). RPM front A-arms for the Electric versions of the Traxxas Slash, Rustler & Stampede are sold in pairs and are available in black, green, blue and red. These A-arms are molded with what is fast becoming an RPM trademark design of angled leading and trailing edges to reduce frontal edge mass and improve the a-arm’s ability to ride up and over tall obstacles instead of slamming into them. RPM A-arms are extremely rigid for a superior ride and stability over the roughest tracks and terrain.

149,-

Hovedbilde RPM 80244 Front A-Arms Green Slash/Rustler/Elec ...

Hovedbilde RPM 80244 Front A-Arms Green Slash/Rustler/Elec ...

RPM 80244 Front A-Arms Green Slash/Rustler/Elec ...

Art.nr: 80244

Copied

RPM Front Arms for the 2WD: Slash, Nitro Slash, Rustler & Stampede - Green Replaces stock Traxxas #3631 Quick Notes: Fits all versions of the Traxxas 2WD: Slash, Nitro Slash, Stampede & Rustler Nearly 25% lighter than stock Replaces stock Traxxas #3631 RPM front A-arms for the Traxxas Slash 2wd, Nitro Slash, e-Rustler & e-Stampede 2wd are built to withstand some of the toughest abuse. Incredibly, we were able to shave some unwanted unsprung weight as well. RPM Front A-arms are nearly 25% lighter than stock versions of the same A-arms, yet the RPM versions are backed with our world-renowned breakage warranty. Additionally, we’ve increased clearance areas in the outer portion of the A-arms to allow increased droop travel when used in conjunction with RPM oversized bearing carriers (RPM #80372 & #80382). RPM front A-arms for the Electric versions of the Traxxas Slash, Rustler & Stampede are sold in pairs and are available in black, green, blue and red. These A-arms are molded with what is fast becoming an RPM trademark design of angled leading and trailing edges to reduce frontal edge mass and improve the a-arm’s ability to ride up and over tall obstacles instead of slamming into them. RPM A-arms are extremely rigid for a superior ride and stability over the roughest tracks and terrain.

149,-

Hovedbilde RPM 80245 Front Arms for the 2WD: Slash, Nitro Slash, ...

RPM 80245 Front Arms for the 2WD: Slash, Nitro Slash, ...

Art.nr: 80245

Copied

RPM Front Arms for the 2WD: Slash, Nitro Slash, Rustler & Stampede - Blue Replaces stock Traxxas #3631 Quick Notes: Fits all versions of the Traxxas 2WD: Slash, Nitro Slash, Stampede & Rustler Nearly 25% lighter than stock Replaces stock Traxxas #3631 RPM front A-arms for the Traxxas Slash 2wd, Nitro Slash, e-Rustler & e-Stampede 2wd are built to withstand some of the toughest abuse. Incredibly, we were able to shave some unwanted unsprung weight as well. RPM Front A-arms are nearly 25% lighter than stock versions of the same A-arms, yet the RPM versions are backed with our world-renowned breakage warranty. Additionally, we’ve increased clearance areas in the outer portion of the A-arms to allow increased droop travel when used in conjunction with RPM oversized bearing carriers (RPM #80372 & #80382). RPM front A-arms for the Electric versions of the Traxxas Slash, Rustler & Stampede are sold in pairs and are available in black, green, blue and red. These A-arms are molded with what is fast becoming an RPM trademark design of angled leading and trailing edges to reduce frontal edge mass and improve the a-arm’s ability to ride up and over tall obstacles instead of slamming into them. RPM A-arms are extremely rigid for a superior ride and stability over the roughest tracks and terrain.

109,-

Hovedbilde RPM 80247 Front Arms for the 2WD: Slash, Nitro Slash, ...

RPM 80247 Front Arms for the 2WD: Slash, Nitro Slash, ...

Art.nr: 80247

Copied

RPM Front Arms for the 2WD: Slash, Nitro Slash, Rustler & Stampede - Pink Replaces stock Traxxas #3631 Quick Notes: Fits all versions of the Traxxas 2WD: Slash, Nitro Slash, Stampede & Rustler Nearly 25% lighter than stock Replaces stock Traxxas #3631 RPM front A-arms for the Traxxas Slash 2wd, Nitro Slash, e-Rustler & e-Stampede 2wd are built to withstand some of the toughest abuse. Incredibly, we were able to shave some unwanted unsprung weight as well. RPM Front A-arms are nearly 25% lighter than stock versions of the same A-arms, yet the RPM versions are backed with our world-renowned breakage warranty. Additionally, we’ve increased clearance areas in the outer portion of the A-arms to allow increased droop travel when used in conjunction with RPM oversized bearing carriers (RPM #80372 & #80382). RPM front A-arms for the Electric versions of the Traxxas Slash, Rustler & Stampede are sold in pairs and are available in black, green, blue and red. These A-arms are molded with what is fast becoming an RPM trademark design of angled leading and trailing edges to reduce frontal edge mass and improve the a-arm’s ability to ride up and over tall obstacles instead of slamming into them. RPM A-arms are extremely rigid for a superior ride and stability over the roughest tracks and terrain.

139,-

Hovedbilde RPM 80249 Front A-Arms Slash 2WD/Rustler/Stampede 2WD ...

RPM 80249 Front A-Arms Slash 2WD/Rustler/Stampede 2WD ...

Art.nr: 80249

Copied

RPM Front Arms for the 2WD: Slash, Nitro Slash, Rustler & Stampede - Red Replaces stock Traxxas #3631 Quick Notes: Fits all versions of the Traxxas 2WD: Slash, Nitro Slash, Stampede & Rustler Nearly 25% lighter than stock Replaces stock Traxxas #3631 RPM front A-arms for the Traxxas Slash 2wd, Nitro Slash, e-Rustler & e-Stampede 2wd are built to withstand some of the toughest abuse. Incredibly, we were able to shave some unwanted unsprung weight as well. RPM Front A-arms are nearly 25% lighter than stock versions of the same A-arms, yet the RPM versions are backed with our world-renowned breakage warranty. Additionally, we’ve increased clearance areas in the outer portion of the A-arms to allow increased droop travel when used in conjunction with RPM oversized bearing carriers (RPM #80372 & #80382). RPM front A-arms for the Electric versions of the Traxxas Slash, Rustler & Stampede are sold in pairs and are available in black, green, blue and red. These A-arms are molded with what is fast becoming an RPM trademark design of angled leading and trailing edges to reduce frontal edge mass and improve the a-arm’s ability to ride up and over tall obstacles instead of slamming into them. RPM A-arms are extremely rigid for a superior ride and stability over the roughest tracks and terrain

109,-

Hovedbilde RPM 80372 Front Bearing Carriers ...

RPM 80372 Front Bearing Carriers ...

Art.nr: 80372

Copied

RPM Front Bearing Carriers for 2WD Slash, Nitro Slash, Stampede & Rustler - Black Replaces stock Traxxas #3736 Quick Links: Fits Traxxas 2WD Slash, Nitro Slash, Rustler, Stampede & Bandit VXL Replaces stock Traxxas #3736 5x11x4mm. bearings not included Optional matching Rear Bearing Carriers are also available Optional matching Caster Blocks are also available RPM bearing carriers are the perfect solution for a nearly indestructible front axle carrier to handle your toughest race or bash session. Our bearing carriers are so strong; we guarantee that they won’t ever break! Molded in black or blue from our trademark blend of engineering grade nylons. When used in conjunction with our Rear Bearing Carriers, you’ll never have to worry about damaged bearing carriers again! Tech Notes: First generation vehicles (vehicles made prior to 2010) that come with 5x8mm bushings will need to purchase replacement 5x11x4mm bearings. 5x11x4mm bearings are not included with these kits (4 bearings are required for each kit).

129,-

Hovedbilde RPM 80375 Front Bearing Carriers for 2WD Slash, Nitro ...

RPM 80375 Front Bearing Carriers for 2WD Slash, Nitro ...

Art.nr: 80375

Copied

RPM Front Bearing Carriers for 2WD Slash, Nitro Slash, Stampede & Rustler - Blue Replaces stock Traxxas #3736 Quick Links: Fits Traxxas 2WD Slash, Nitro Slash, Rustler, Stampede & Bandit VXL Replaces stock Traxxas #3736 5x11x4mm. bearings not included Optional matching Rear Bearing Carriers are also available Optional matching Caster Blocks are also available RPM bearing carriers are the perfect solution for a nearly indestructible front axle carrier to handle your toughest race or bash session. Our bearing carriers are so strong; we guarantee that they won’t ever break! Molded in black or blue from our trademark blend of engineering grade nylons. When used in conjunction with our Rear Bearing Carriers, you’ll never have to worry about damaged bearing carriers again! Tech Notes: First generation vehicles (vehicles made prior to 2010) that come with 5x8mm bushings will need to purchase replacement 5x11x4mm bearings. 5x11x4mm bearings are not included with these kits (4 bearings are required for each kit).

129,-

Hovedbilde RPM 80382 Rear Bearing Carriers Rustler/Stampede/Slash ...

Hovedbilde RPM 80382 Rear Bearing Carriers Rustler/Stampede/Slash ...

RPM 80382 Rear Bearing Carriers Rustler/Stampede/Slash ...

Art.nr: 80382

Copied

RPM Rear Bearing Carriers for 2WD Slash, Nitro Slash, Stampede, Rustler & Bandit - Black Replaces stock Traxxas #3752 Quick Notes: Fits the Traxxas 2WD Slash, Rustler, Stampede & Bandit Replaces stock Traxxas #3752 5x11x4mm. bearings not included Not for use on 4×4 versions of the Rustler, Stampede or Slash Identical in strength and performance as our Front Bearing Carriers, these rear carriers will get you to the finish line every time! Our bearing carriers are molded from RPM’s bulletproof blend of nylons and are guaranteed not break! Molded in black or blue. Tech Notes: First generation vehicles (vehicles made prior to 2010) that come with 5x8mm bushings will need to purchase replacement 5x11x4mm bearings (not included). Later moels use a 5x11x4mm bearing as a stock size and can be directly transferred to RPM versions. 5x11x4mm bearings are not included with these kits (4 bearings are required for each kit).

129,-

139,-

-7%

Hovedbilde RPM 80385 Rear Bearing Carriers Rust/Stamp/Slsh ...

RPM 80385 Rear Bearing Carriers Rust/Stamp/Slsh ...

Art.nr: 80385

Copied

RPM Rear Bearing Carriers for 2WD Slash, Nitro Slash, Stampede, Rustler & Bandit - Blue Replaces stock Traxxas #3752 Quick Notes: Fits the Traxxas 2WD Slash, Rustler, Stampede & Bandit Replaces stock Traxxas #3752 5x11x4mm. bearings not included Not for use on 4×4 versions of the Rustler, Stampede or Slash Identical in strength and performance as our Front Bearing Carriers, these rear carriers will get you to the finish line every time! Our bearing carriers are molded from RPM’s bulletproof blend of nylons and are guaranteed not break! Molded in black or blue. Tech Notes: First generation vehicles (vehicles made prior to 2010) that come with 5x8mm bushings will need to purchase replacement 5x11x4mm bearings (not included). Later moels use a 5x11x4mm bearing as a stock size and can be directly transferred to RPM versions. 5x11x4mm bearings are not included with these kits (4 bearings are required for each kit).

89,-

Hovedbilde RPM 80522 Gear Cover - Black Replaces TRX 3792

RPM 80522 Gear Cover - Black Replaces TRX 3792

Art.nr: 80522

Copied

RPM Gear Cover for 2WD Rustler, Stampede, Bandit & Slash - Black Replaces the stock Traxxas #3792 Quick Notes: Fits all versions of the Traxxas 2WD Rustler, Stampede, Bandit & Slash Not recommended for spur gears larger than the stock 87 teeth Replaces the stock Traxxas #3792 The most recent electric versions of the Rustler, Stampede, Bandit and Slash 2wd have several new features that caused interference issues with our original RPM molded gear cover for the Stampede & Rustler. We expanded the area of the gear cover over the motor shaft to compensate for the longer motor shaft of the XL-5 & VXL motors. We narrowed two areas along the perimeter of the gear cover to allow clearance for the rear bumper / wheelie bar mount as well. These changes now allow this gear cover to fit all versions of these awesome vehicles. Additional features designed into these gear covers include such important aspects as: An oversized access hole and soft plug for easy access to the slipper clutch nut while still maintaining an unmatched seal of the gear mesh area. Our plug stays in place yet is easy to remove and install. Completely sealed. Stock gear covers have a large, open gap between the spur gear and the out-drive that allows gear destroying dirt to enter. Sleek contours that would look great on any vehicle. More clearance for larger pinions for owners hungry for speed. Retains all stock geometry for easy bolt up; no cutting or gluing required. Not only do they look great, they will protect those expensive gears like nothing else available! RPM‘s new gear cover will pay for itself the very first time you run through the dirt and nothing enters your gear case. No more blown gears from rocks and debris! RPM Gear Covers for the electric versions of the Traxxas Stampede 2wd, Rustler, Bandit and Slash 2wd are sold in black, green, blue or red and carry our limited lifetime warranty against failure due to materials or workmanship issues. Tech Notes: Replaces stock Traxxas #3792. Does not include provisions for telemetry. Not recommended for spur gears larger than the stock 87 teeth.

99,-

Hovedbilde RPM 80524 Gear Cover Green Bandit, Rustler, Stampede, ...

Hovedbilde RPM 80524 Gear Cover Green Bandit, Rustler, Stampede, ...

RPM 80524 Gear Cover Green Bandit, Rustler, Stampede, ...

Art.nr: 80524

Copied

RPM Gear Cover for 2WD Rustler, Stampede, Bandit & Slash - Green Replaces the stock Traxxas #3792 Quick Notes: Fits all versions of the Traxxas 2WD Rustler, Stampede, Bandit & Slash Not recommended for spur gears larger than the stock 87 teeth Replaces the stock Traxxas #3792 The most recent electric versions of the Rustler, Stampede, Bandit and Slash 2wd have several new features that caused interference issues with our original RPM molded gear cover for the Stampede & Rustler. We expanded the area of the gear cover over the motor shaft to compensate for the longer motor shaft of the XL-5 & VXL motors. We narrowed two areas along the perimeter of the gear cover to allow clearance for the rear bumper / wheelie bar mount as well. These changes now allow this gear cover to fit all versions of these awesome vehicles. Additional features designed into these gear covers include such important aspects as: An oversized access hole and soft plug for easy access to the slipper clutch nut while still maintaining an unmatched seal of the gear mesh area. Our plug stays in place yet is easy to remove and install. Completely sealed. Stock gear covers have a large, open gap between the spur gear and the out-drive that allows gear destroying dirt to enter. Sleek contours that would look great on any vehicle. More clearance for larger pinions for owners hungry for speed. Retains all stock geometry for easy bolt up; no cutting or gluing required. Not only do they look great, they will protect those expensive gears like nothing else available! RPM‘s new gear cover will pay for itself the very first time you run through the dirt and nothing enters your gear case. No more blown gears from rocks and debris! RPM Gear Covers for the electric versions of the Traxxas Stampede 2wd, Rustler, Bandit and Slash 2wd are sold in black, green, blue or red and carry our limited lifetime warranty against failure due to materials or workmanship issues. Tech Notes: Replaces stock Traxxas #3792. Does not include provisions for telemetry. Not recommended for spur gears larger than the stock 87 teeth.

99,-

Hovedbilde RPM 80527 Gear Cover Pink Bandit, Rustler, Stampede, ...

RPM 80527 Gear Cover Pink Bandit, Rustler, Stampede, ...

Art.nr: 80527

Copied

RPM Gear Cover for 2WD Rustler, Stampede, Bandit & Slash - Pink Replaces the stock Traxxas #3792 Quick Notes: Fits all versions of the Traxxas 2WD Rustler, Stampede, Bandit & Slash Not recommended for spur gears larger than the stock 87 teeth Replaces the stock Traxxas #3792 The most recent electric versions of the Rustler, Stampede, Bandit and Slash 2wd have several new features that caused interference issues with our original RPM molded gear cover for the Stampede & Rustler. We expanded the area of the gear cover over the motor shaft to compensate for the longer motor shaft of the XL-5 & VXL motors. We narrowed two areas along the perimeter of the gear cover to allow clearance for the rear bumper / wheelie bar mount as well. These changes now allow this gear cover to fit all versions of these awesome vehicles. Additional features designed into these gear covers include such important aspects as: An oversized access hole and soft plug for easy access to the slipper clutch nut while still maintaining an unmatched seal of the gear mesh area. Our plug stays in place yet is easy to remove and install. Completely sealed. Stock gear covers have a large, open gap between the spur gear and the out-drive that allows gear destroying dirt to enter. Sleek contours that would look great on any vehicle. More clearance for larger pinions for owners hungry for speed. Retains all stock geometry for easy bolt up; no cutting or gluing required. Not only do they look great, they will protect those expensive gears like nothing else available! RPM‘s new gear cover will pay for itself the very first time you run through the dirt and nothing enters your gear case. No more blown gears from rocks and debris! RPM Gear Covers for the electric versions of the Traxxas Stampede 2wd, Rustler, Bandit and Slash 2wd are sold in black, green, blue or red and carry our limited lifetime warranty against failure due to materials or workmanship issues. Tech Notes: Replaces stock Traxxas #3792. Does not include provisions for telemetry. Not recommended for spur gears larger than the stock 87 teeth.

99,-

Hovedbilde RPM 80529 Gear Cover for the Traxxas e-Rustler, ...

RPM 80529 Gear Cover for the Traxxas e-Rustler, ...

Art.nr: 80529

Copied

Gear Cover for the Traxxas e-Rustler, e-Stampede 2wd, Bandit & Slash 2wd replaces stock Traxxas #3792 Quick Notes: – fits all versions of the Traxxas electric Rustler, electric Stampede 2wd, Bandit & Slash 2wd – not recommended for spur gears larger than the stock 87 teeth – replaces stock Traxxas #3792 The most recent electric versions of the Rustler, Stampede, Bandit and Slash 2wd have several new features that caused interference issues with our original RPM molded gear cover for the Stampede & Rustler. We expanded the area of the gear cover over the motor shaft to compensate for the longer motor shaft of the XL-5 & VXL motors. We narrowed two areas along the perimeter of the gear cover to allow clearance for the rear bumper / wheelie bar mount as well. These changes now allow this gear cover to fit all versions of these awesome vehicles. Additional features designed into these gear covers include such important aspects as: An oversized access hole and soft plug for easy access to the slipper clutch nut while still maintaining an unmatched seal of the gear mesh area. Our plug stays in place yet is easy to remove and install. Completely sealed. Stock gear covers have a large, open gap between the spur gear and the out-drive that allows gear destroying dirt to enter. Sleek contours that would look great on any vehicle. More clearance for larger pinions for owners hungry for speed. Retains all stock geometry for easy bolt up; no cutting or gluing required. Not only do they look great, they will protect those expensive gears like nothing else available! RPM‘s new gear cover will pay for itself the very first time you run through the dirt and nothing enters your gear case. No more blown gears from rocks and debris! Tech Notes: Replaces stock Traxxas #3792. Does not include provisions for telemetry. Not recommended for spur gears larger than the stock 87 teeth.

99,-

Hovedbilde RPM 80702 Front or Rear A-arms for the Traxxas Slash ...

RPM 80702 Front or Rear A-arms for the Traxxas Slash ...

Art.nr: 80702

Copied

Front or Rear A-arms for the Traxxas Slash 4×4, Stampede 4×4, Rustler 4×4, Hoss 4×4 & Rally Replaces TRX 3655R & 3655X Quick Notes: Fits the 1/10 versions of the Slash 4×4, Stampede 4×4, Hoss 4×4 & Rally 4×4 Does not fit the Rally ST (please see RPM #73362) Each a-arm is 6.5 grams lighter than stock*! 2 packages is needed to complete one full vehicle (front & rear) Replaces stock Traxxas #3655R & #3655X RPM A-arms for the Traxxas Slash 4×4, Rustler 4×4, Hoss 4×4 & Stampede 4×4 are everything you’ve come to expect from RPM and more! Take a look at everything we’ve done: We eliminated the slop in the suspension system, tightening the tolerances around the hinge pins, reduced the fore and aft movement of the A-arms at both the inner hinge pin and at the axle carriers by better than 90% and improved the durability dramatically (they’re made by RPM, enough said). As a bonus, we cut 6.5 grams of weight off of each A-arm*! That’s a total loss of just under one ounce of weight simply by replacing your stock A-arms with the RPM versions! We can’t forget about how much better aesthetically the RPM versions look either. RPM A-arms carry over our traditional look with our 30 degree leading and trailing edges, and huge bosses for the shocks and sway bar mounts. Additionally, you now have the option of a bit of color with black, blue, green and red to choose from. RPM A-arms are molded in our trademark blend of incredibly durable nylons and are backed by an industry leading warranty. We proudly stand behind our products! Designed, manufactured and produced right here in southern California in the USA! Tech Notes: Replaces stock Traxxas #3655R & #3655X. RPM A-arms will not fit ST versions of the Rally (please see RPM #73362). RPM arms are sold in sets of 1 – left and 1 – right A-arm in each package. Two packages will be needed to complete one truck. The upper hinge pin hole of the rear axle carriers cannot be used (not a stock location for the Slash 4×4) due to strengthening designs that reduce the clearance around the rear axle. *Weight comparison based on Traxxas #3655X.

159,-

Hovedbilde RPM 80704 Front or Rear A-arms Green for the TRX Slash ...

RPM 80704 Front or Rear A-arms Green for the TRX Slash ...

Art.nr: 80704

Copied

Front or Rear A-arms for the Traxxas Slash 4×4, Stampede 4×4, Rustler 4×4, Hoss 4×4 & Rally Green Replaces TRX 3655R & 3655X Quick Notes: Fits the 1/10 versions of the Slash 4×4, Stampede 4×4, Hoss 4×4 & Rally 4×4 Does not fit the Rally ST (please see RPM #73362) Each a-arm is 6.5 grams lighter than stock*! 2 packages is needed to complete one full vehicle (front & rear) Replaces stock Traxxas #3655R & #3655X RPM A-arms for the Traxxas Slash 4×4, Rustler 4×4, Hoss 4×4 & Stampede 4×4 are everything you’ve come to expect from RPM and more! Take a look at everything we’ve done: We eliminated the slop in the suspension system, tightening the tolerances around the hinge pins, reduced the fore and aft movement of the A-arms at both the inner hinge pin and at the axle carriers by better than 90% and improved the durability dramatically (they’re made by RPM, enough said). As a bonus, we cut 6.5 grams of weight off of each A-arm*! That’s a total loss of just under one ounce of weight simply by replacing your stock A-arms with the RPM versions! We can’t forget about how much better aesthetically the RPM versions look either. RPM A-arms carry over our traditional look with our 30 degree leading and trailing edges, and huge bosses for the shocks and sway bar mounts. Additionally, you now have the option of a bit of color with black, blue, green and red to choose from. RPM A-arms are molded in our trademark blend of incredibly durable nylons and are backed by an industry leading warranty. We proudly stand behind our products! Designed, manufactured and produced right here in southern California in the USA! Tech Notes: Replaces stock Traxxas #3655R & #3655X. RPM A-arms will not fit ST versions of the Rally (please see RPM #73362). RPM arms are sold in sets of 1 – left and 1 – right A-arm in each package. Two packages will be needed to complete one truck. The upper hinge pin hole of the rear axle carriers cannot be used (not a stock location for the Slash 4×4) due to strengthening designs that reduce the clearance around the rear axle. *Weight comparison based on Traxxas #3655X.

159,-

Hovedbilde RPM 80705 Front or Rear A-arms for the Traxxas Slash ...

RPM 80705 Front or Rear A-arms for the Traxxas Slash ...

Art.nr: 80705

Copied

RPM Front or Rear A-arms for the Traxxas Slash 4×4, Stampede 4×4, Rustler 4×4, Hoss 4×4 & Rally Replaces TRX 3655R & 3655X Quick Notes: Fits the 1/10 versions of the Slash 4×4, Stampede 4×4, Hoss 4×4 & Rally 4×4 Does not fit the Rally ST (please see RPM #73362) Each a-arm is 6.5 grams lighter than stock*! 2 packages is needed to complete one full vehicle (front & rear) Replaces stock Traxxas #3655R & #3655X RPM A-arms for the Traxxas Slash 4×4, Rustler 4×4, Hoss 4×4 & Stampede 4×4 are everything you’ve come to expect from RPM and more! Take a look at everything we’ve done: We eliminated the slop in the suspension system, tightening the tolerances around the hinge pins, reduced the fore and aft movement of the A-arms at both the inner hinge pin and at the axle carriers by better than 90% and improved the durability dramatically (they’re made by RPM, enough said). As a bonus, we cut 6.5 grams of weight off of each A-arm*! That’s a total loss of just under one ounce of weight simply by replacing your stock A-arms with the RPM versions! We can’t forget about how much better aesthetically the RPM versions look either. RPM A-arms carry over our traditional look with our 30 degree leading and trailing edges, and huge bosses for the shocks and sway bar mounts. Additionally, you now have the option of a bit of color with black, blue, green and red to choose from. RPM A-arms are molded in our trademark blend of incredibly durable nylons and are backed by an industry leading warranty. We proudly stand behind our products! Designed, manufactured and produced right here in southern California in the USA! Tech Notes: Replaces stock Traxxas #3655R & #3655X. RPM A-arms will not fit ST versions of the Rally (please see RPM #73362). RPM arms are sold in sets of 1 – left and 1 – right A-arm in each package. Two packages will be needed to complete one truck. The upper hinge pin hole of the rear axle carriers cannot be used (not a stock location for the Slash 4×4) due to strengthening designs that reduce the clearance around the rear axle.

159,-

Hovedbilde RPM 80709 Front or Rear A-arms for Slash 4×4, Stampede ...

RPM 80709 Front or Rear A-arms for Slash 4×4, Stampede ...

Art.nr: 80709

Copied

RPM Front or Rear A-arms for Slash 4×4, Stampede 4×4, Rustler 4×4 & Hoss 4×4 - Red Replaces stock Traxxas #3655R & #3655X Quick Notes: Fits the 1/10 versions of the Slash 4×4, Stampede 4×4, Hoss 4×4 & Rally 4×4 Does not fit the Rally ST (please see RPM #73362) Each a-arm is 6.5 grams lighter than stock*! 2 packages is needed to complete one full vehicle (front & rear) Replaces stock Traxxas #3655R & #3655X RPM A-arms for the Traxxas Slash 4×4, Rustler 4×4, Hoss 4×4 & Stampede 4×4 are everything you’ve come to expect from RPM and more! Take a look at everything we’ve done: We eliminated the slop in the suspension system, tightening the tolerances around the hinge pins, reduced the fore and aft movement of the A-arms at both the inner hinge pin and at the axle carriers by better than 90% and improved the durability dramatically (they’re made by RPM, enough said). As a bonus, we cut 6.5 grams of weight off of each A-arm*! That’s a total loss of just under one ounce of weight simply by replacing your stock A-arms with the RPM versions! We can’t forget about how much better aesthetically the RPM versions look either. RPM A-arms carry over our traditional look with our 30 degree leading and trailing edges, and huge bosses for the shocks and sway bar mounts. Additionally, you now have the option of a bit of color with black, blue, green and red to choose from. RPM A-arms are molded in our trademark blend of incredibly durable nylons and are backed by an industry leading warranty. We proudly stand behind our products! Designed, manufactured and produced right here in southern California in the USA! Tech Notes: Replaces stock Traxxas #3655R & #3655X. RPM A-arms will not fit ST versions of the Rally (please see RPM #73362). RPM arms are sold in sets of 1 – left and 1 – right A-arm in each package. Two packages will be needed to complete one truck. The upper hinge pin hole of the rear axle carriers cannot be used (not a stock location for the Slash 4×4) due to strengthening designs that reduce the clearance around the rear axle.

159,-

Hovedbilde RPM 80712 Caster Blocks for 2WD Slash, Nitro Slash, ...

Hovedbilde RPM 80712 Caster Blocks for 2WD Slash, Nitro Slash, ...

RPM 80712 Caster Blocks for 2WD Slash, Nitro Slash, ...

Art.nr: 80712

Copied

RPM Caster Blocks for 2WD Slash, Nitro Slash, Stampede & Rustler - Black Replaces Traxxas stock #3632 Quick Notes: Replaces Traxxas stock #3632 Will not work on nitro versions of the Rustler & Stampede Will not work on 4WD versions of the Stampede, Rustler or Slash RPM Caster Blocks for the Traxxas Slash 2wd, nitro Slash, electric Rustler & electric Stampede 2wd are the final link for a complete, bulletproof front suspension from RPM for these trucks. RPM Caster Blocks are redesigned to slim down unnecessary bulk while improving strength and durability in this heavily impacted area. These are stock replacement items. No additional parts or modifications are necessary to mount a set to a vehicle. RPM Caster Blocks are molded in our trademark blend of ultra durable and super strong nylons and backed by the best breakage warranty in the R/C industry. Each package contains one left side and one right side caster block. Tech Notes: RPM #80712 & #80715 Caster Blocks replace Traxxas stock #3632 Caster Blocks. RPM Caster Blocks retain stock Rustler & Stampede 30 degree caster settings. These Caster Blocks will not work on nitro versions of the Rustler & Stampede nor 4wd versions of the Stampede, Rustler or Slash.

149,-

Hovedbilde RPM 80832 Rear Shock Tower for Slash 2WD, Stampede 2WD ...

RPM 80832 Rear Shock Tower for Slash 2WD, Stampede 2WD ...

Art.nr: 80832

Copied

RPM Rear Shock Tower for Slash 2WD, Stampede 2WD & Rustler 2WD Replaces stock Traxxas #3638 Quick Notes: Replaces stock Traxxas #3638 Fits Traxxas Slash 2WD, Stampede 2WD & Rustler 2WD Also fits the Bandit but see the “Tech Notes” below for important information Optional Front Shock Tower is also available RPM rear shock towers for the electric versions of the Slash, Stampede, Rustler & Bandit were designed with one thing in mind – rugged durability. Once again, we’ve exceeded our own expectations with this shock tower. While we’ve maintained all stock geometry on these shock towers, we’ve beefed them up in all the right places to eliminate annoying rear shock tower breakage. Our version of this shock tower uses an I-Beam construction that improves durability and rigidity as well. At the base of the shock tower, we’ve improved the screws’ head clearance of the bulkhead mounting screws to eliminate the bind normally associated with the stock rear shock tower. All these design elements combine to create the ultimate lightweight, bulletproof rear shock tower for the electric versions of the Slash, Rustler & Stampede. RPM rear shock towers for the Traxxas Slash, Electric Stampede, Electric Rustler & Bandit are molded in black and are backed by our famous breakage warranty. These towers are direct replacement parts for ease of installation. Tech Notes: These rear shock towers can be used on the Traxxas Bandit. However, there are no provisions for a rear wing built in.

99,-

Hovedbilde RPM 80852 Front Shock Tower for 2WD Slash, Stampede, ...

RPM 80852 Front Shock Tower for 2WD Slash, Stampede, ...

Art.nr: 80852

Copied

RPM Front Shock Tower for 2WD Slash, Stampede, Rustler & Bandit Replaces stock Traxxas #3639 Quick Notes: Replaces stock Traxxas #3639 Optional Rear Shock Tower is also available RPM shock towers for Traxxas 1/10th scale trucks are designed to add strength and support to the front-end suspension components of these great vehicles. Our shock towers maintain all stock geometry while adding much needed structural strength to this vital suspension component. Our design uses an I-beam structure that adds tremendous levels of strength and rigidity that is far superior to u-shaped or flat designs. Our front shock towers will not flex nearly as easily as the stock versions yet have enough give in them, which prevents breakage from hard impacts or crashes. RPM shock towers are molded in black and are made from our well-reputed blend of materials. These shock towers are so strong; we back them for life with our world renowned warranty policy against breakage.

99,-

Hovedbilde RPM 80902 Rear Bumper Mount Black Slash / Rust / Stmpd ...

RPM 80902 Rear Bumper Mount Black Slash / Rust / Stmpd ...

Art.nr: 80902

Copied

Mount for Rear Bumper or Wheelie Bar for the Traxxas Slash 2wd, e-Rustler, e-Stampede 2wd & Bandit replaces Traxxas stock #3677 Quick Notes: – fits the Traxxas Slash 2wd, e-Rustler, e-Stampede 2wd & Bandit – replaces Traxxas stock #3677 After hearing numerous requests to look into the rear bumper mount on the Traxxas Slash, we found several issues that could use the RPM touch. Those same problems were encountered on e-Rustler, e-Stampede & Bandit vehicles as well, using the stock wheelie bar mount. The problem – the stock mount uses only a single screw on the gear cover side to hold the mount in place. That causes a hinge effect under rear impacts causing the slotted area holding on to the rear skid plate to pop off after an impact, leaving the stock bumper / wheelie bar mount hanging under the chassis. The RPM solution… An all-new bumper mounting system that eliminates all of the problems encountered with the stock version. The RPM rear bumper / wheelie bar mount has two mounting holes on the gear cover side and three on the motor side – that’s two additional mounting points to eliminate that annoying hinge effect mentioned above. The additional mounting screws help disperse impact energy into the transmission case over more surface area, reducing the possibility of damaging the case significantly! The new RPM mount design means no more slotted parts hanging below the rear skid plate – ever! Our mount tucks up quite nicely behind the skid plate for better rear end ground clearance. Our rear bumper / wheelie bar mount fits a wide range of vehicles too. It fits all versions of the Traxxas Slash 2wd, electric Stampede, electric Rustler and Bandit including VXL, XL-5 and legacy versions. The RPM rear bumper / wheelie bar mount is molded in our nearly indestructible blend of nylons and is sold in either blue or black. Each mount comes with all necessary hardware, complete instructions for ease of installation and an industry-leading warranty to back it all up! Tech Notes: The RPM Rear Bumper Mount replaces Traxxas #3677.

139,-

Hovedbilde RPM 80905 Mount for Rear Bumper or Wheelie Bar for 2WD ...

Hovedbilde RPM 80905 Mount for Rear Bumper or Wheelie Bar for 2WD ...

RPM 80905 Mount for Rear Bumper or Wheelie Bar for 2WD ...

Art.nr: 80905

Copied

RPM Mount for Rear Bumper or Wheelie Bar for 2WD Slash, Rustler, Stampede & Bandit - Blue Replaces Traxxas stock #3677 Quick Notes: Fits Traxxas 2WD Slash, Rustler, Stampede & Bandit Replaces Traxxas stock #3677 After hearing numerous requests to look into the rear bumper mount on the Traxxas Slash, we found several issues that could use the RPM touch. Those same problems were encountered on e-Rustler, e-Stampede & Bandit vehicles as well, using the stock wheelie bar mount. The problem – the stock mount uses only a single screw on the gear cover side to hold the mount in place. That causes a hinge effect under rear impacts causing the slotted area holding on to the rear skid plate to pop off after an impact, leaving the stock bumper / wheelie bar mount hanging under the chassis. The RPM solution… An all-new bumper mounting system that eliminates all of the problems encountered with the stock version. The RPM rear bumper / wheelie bar mount has two mounting holes on the gear cover side and three on the motor side – that’s two additional mounting points to eliminate that annoying hinge effect mentioned above. The additional mounting screws help disperse impact energy into the transmission case over more surface area, reducing the possibility of damaging the case significantly! The new RPM mount design means no more slotted parts hanging below the rear skid plate – ever! Our mount tucks up quite nicely behind the skid plate for better rear end ground clearance. Our rear bumper / wheelie bar mount fits a wide range of vehicles too. It fits all versions of the Traxxas Slash 2wd, electric Stampede, electric Rustler and Bandit including VXL, XL-5 and legacy versions. The RPM rear bumper / wheelie bar mount is molded in our nearly indestructible blend of nylons and is sold in either blue or black. Each mount comes with all necessary hardware, complete instructions for ease of installation and an industry-leading warranty to back it all up! Tech Notes: The RPM Rear Bumper Mount replaces Traxxas #3677.

139,-

Viser 26 til 50 (av 211 produkter)