Hopp til innhold

Reservedeler Båt

Populært i denne kategorien

Art.nr: TRX 3829
Copied
Driveshaft/ stuffing tube/bushings (self-lubricating) (2)

55,-

KONTAKT
Art.nr: TRX 3834
Copied
  Propeller plastic

85,-

KJØP
Art.nr: TRX 3840
Copied
Rubber grommet for driveshaft (stuffing) tube (2)

29,-

KJØP
Art.nr: TRX 3875
Copied
Water cooling system WATER COOLING KIT: Water cooling is a highly recommended upgrade for the Blast, and mandatory if aftermarket motors are used. The cooling system consists of tubing which picks up water from underneath the boat, circulates it through coils wrapped around the motor, and then exits it through the side or rear of the boat

169,-

KJØP
Art.nr: TRX 3924
Copied
Box, receiver (sealed)/ foam pad/ silicone grease/2.5x8mm BCS (2)/ 3x10mm CCS (2)/ 3x15mm CCS (2) Sealed receiver box for Traxxas micro receivers. Includes foam pad, silicone seal, grease, 3x10 mm screws (2), 2.5x8 mm screws, and 3x15 mm screws (2).

149,-

169,-

KJØP
-12%
Art.nr: TRX 3925
Copied
This is the Seal Kit Receiver Box. Fits: Traxxas E-Maxx/E-Maxx Brushless Traxxas Slash 4x4

49,-

KJØP
Art.nr: TRX 5345R
Copied
These are the Steering Servo Horns and Turnbuckles                              from Traxxas. FEATURES: Nylon construction, black in color INCLUDES: Two long steering servo horns           Two short steering servo horns           Two 3x20mm turnbuckles REQUIRES: Installation on the vehicle

79,-

KJØP
Art.nr: TRX 5712X
Copied
Hatch, Spartan, white (no graphics)

245,-

KJØP
Art.nr: TRX 5713
Copied
This is the Decal Sheet for the Traxxas Spartan Deep V Boat FEATURES Precut for easy peel and stick application INCLUDES "Traxxas" and "Spartan" logos in black, white and red with all hull trim items REQUIREMENTS Applying to hull

145,-

KJØP
Art.nr: TRX 5722
Copied
These are the Battery Straps for the Spartan Boat from Traxxas FEATURES Black color velcro strap INCLUDES 4 battery straps SPECIFICATIONS Length: 9" (228mm) Width: .62" (16mm)

79,-

KJØP
Art.nr: TRX 5723
Copied
This is the Hatch Post and Hull Water Outlet Set for the Spartan  from Traxxas     FEATURES Black plastic construction   INCLUDES Hatch post  Hull water outlet  4x8mm BCS  3x4mm BCS  1 washer  10 foam pads   REQUIREMENTS Installation on vehicle

59,-

KJØP
Art.nr: TRX 5724R
Copied
This is the Radio Tray with Retainer for the Traxxas Spartan Brushless Boat.   FEATURES Nylon construction  Black in color   INCLUDES One radio tray  Two radio tray retainers  One stuffing tube clamp  Two 4x16mm stainless steel buttonhead cap screws  Two 4x10mm stainless steel buttonhead cap screws   REQUIREMENTS Installation into Spartan

169,-

KJØP
Art.nr: TRX 5725
Copied
This is the Rubber Boot for the Rudder Pushrod for the Traxxas Spartan. FEATURES: Rubber construction           Blue in color INCLUDES: One rubber boot and mount REQUIRES: Installation

29,-

KJØP
Art.nr: TRX 5726
Copied
This is the Drive Strut Mount for the Traxxas Spartan Race Boat. FEATURES: Aluminum construction Anodized blue in color INCLUDES: Two drive strut mount pieces REQUIRES: Installation onto boat

89,-

KJØP
Art.nr: TRX 5728
Copied
This is the Replacement 4X3MM Drive Dog for the Spartan from Traxxas FEATURES: Aluminum construction INCLUDES: Drive dog           4X3mm set screw REQUIRES: Installation on prop shaft

39,-

Ikke på lager
Art.nr: TRX 5729
Copied
This is the Propellor Shaft and Flex Cable for the Traxxas Spartan. FEATURES: Steel construction           Silver in color INCLUDES One propellor shaft and flex cable REQUIRES: Installation on to boat SPECS:    Length: 387.35mm (15.25")           Prop Shaft Diameter: 5mm (0.20")           Flex Cable Diameter: 4mm (0.16")

239,-

259,-

Ikke på lager
-8%
Art.nr: TRX 5730
Copied
These are the Stock Trim Tabs for the Traxxas Spartan Race Boat. FEATURES: Stainless steel construction           Pre-drilled for mounting INCLUDES: Two trim tabs w/mounting hardware REQUIRES: Installation

75,-

KJØP
Art.nr: TRX 5731X
Copied
Trim tab adjuster (2)/ 4x12mm BCS stainless (4)/ 3x18mm BCS (stainless) (2)/ NL 3.0 (2)   Erstatter TRX 5731.

245,-

KJØP
Art.nr: TRX 5732
Copied
This is the Turn Fin Set for the Traxxas Spartan Race Boat.    Turn fins are mounted at the rear of the boat and provide stability when     turning, trim plates adjust between fast speed versus optimum handling. FEATURES: Replace bent or broken turn fins with this set           Horizontal sections are known as trim plates and may be bent downward             slightly to improve handling           Stainless steel construction INCLUDES: Two Turn Fins           Four 4x12mm Hex Head Machine Screws REQUIRES: 2.5mm Hex Driver

79,-

KJØP
Art.nr: TRX 5733
Copied
This is the stock 42x59 Propeller for the Spartan Boat from Traxxas. FEATURES: Black nylon construction INCLUDES: One 42x59 propeller REQUIRES: Installation on propeller shaft SPECS:    Shaft Diameter: 4mm

59,-

KJØP
Art.nr: TRX 5733R
Copied
Traxxas 5733R - Propeller, 42x59mm (steel)/ M4x0.7 NL (1) (requires installation of #5742X aluminum rudder mount for Spartan® SR) Upgrade your Spartan® or DCB-M41 with this high-performance steel 42x59 mm prop. Includes locknut. Steel prop requires aluminum rudder mount (5742X) if not already installed.

269,-

299,-

KJØP
-10%
Art.nr: TRX 5734
Copied
This is the Stuffing Tube with Nylon Liner for the Traxxas Spartan. FEATURES: Brass and nylon construction INCLUDES: One Assembled Stuffing Tube REQUIRES: Installation SPECS:    Length: 10.6" (270mm)           Outside Diameter of Stuffing Tube: 0.25" (6.6mm)           Inside Diameter of Nylon Liner:  0.18" (4.5mm)

159,-

179,-

KJØP
-11%
Art.nr: TRX 5740
Copied
This is the Rudder Assembly for the Traxxas Spartan Boat. FEATURES: Aluminum construction           Anodized blue in color INCLUDES: Rudder           Rudder Arm           Hinge Pin           Two 3x15mm Stainless Steel Screws           Two 3mm Locknuts REQUIRES: Installing on rudder mount assembly

319,-

KJØP
Art.nr: TRX 5741
Copied
This is the Rudder Pushrod Assembly for the Spartan Boat from Traxxas FEATURES: Pre-assembled pushrod INCLUDES: Rudder pushrod           Servo horn           3x18mm BCS           (1)3x15mm CS           (1)3x6mm CS           (1) NL 3.0 REQUIRES: Installation on boat

59,-

KJØP
Art.nr: TRX 5742
Copied
This is the Rudder Mount and Pivot for the Traxxas Spartan Boat. FEATURES: Aluminum construction with brass inserts           Anodized blue in color INCLUDES: Rudder Mount and Pivot           Four 4x14mm Stainless Steel Screws           Two 4mm Locknuts REQUIRES: Installing at rear of boat

179,-

Ikke på lager
Viser 76 til 100 (av 191 produkter)
  • klarna-dark.png
  • vipps-orange.png
  • mastercard-full.png
  • visa.png
  • paypal.png