Traxxas

Traxxas 4683 Spur Gear 48P 83T

Art.nr: TRX 4683

39,-

Traxxas

Traxxas

** Ikke på lager

Du vil motta en e-post så snart produktet er på lager!

En feil har oppstått. Prøv igjen

Informasjon
Produsent

Informasjon

This is a 48P, 83T Spur Gear for models with
Traxxas Torque Control Slipper Clutch.

FEATURES: 48 pitch
          83 tooth
          Designed for models with a slipper clutch.
          Black plastic construction

INCLUDES: One spur gear

SPECS: Pitch: 48
Tooth: 83

Produsent

Traxxas

Traxxas

Dette er den beste merket for RC-BIL i hele Norge, nei vi kan vel si hele verden uten å trenge å være redd for at vi sier noe galt!

Relaterte produkter

Hovedbilde Traxxas 3691A Gear Box Left/Right w/Idler Gear Shaft ...

Traxxas 3691A Gear Box Left/Right w/Idler Gear Shaft ...

Art.nr: TRX 3691A

Copied

This is a Left and Right Gearbox half with Idler Shaft for the Traxxas Stampede and Traxxas Rustler. FEATURES: Gray plastic construction Steel idler shaft INCLUDES: One gearbox One idler shaft COMMENTS: This part fit the standard and XL version of both the Stampede and Rustler.

95,-

Hovedbilde Traxxas 3691 Gearbox Halves Left & Right

Traxxas 3691 Gearbox Halves Left & Right

Art.nr: TRX 3691

Copied

These are the left and right gearbox halves for the Traxxas Rusler and Stampede truck kits. Includes: One left and one right gearbox half. Features: Tough black nylon construction. Specs: N/A--these will only work with these two kits. Requires: All the internal gears and shafts Assembly Comments: These do not include the hardware for assembly. Refer to manual for appropriate screws.

99,-

Kunder kjøpte også

Hovedbilde Traxxas 6721T Wing Orange Rustler 4x4

Traxxas 6721T Wing Orange Rustler 4x4

Wing, Rustler 4X4 (orange)/ 3x8 FCS (3)

69,-

Hovedbilde Traxxas 3950X Pinion Gear 20T-32P Hardened Steel

Traxxas 3950X Pinion Gear 20T-32P Hardened Steel

Gear, 20-T pinion (32-p), heavy duty (machined, hardened steel)/ set screw For some drivers, “heavy duty” just won’t cut it. When you drive on the ragged edge, you need parts that can withstand the brutal punishment that LiPo power can dish out. If full-throttle is the only language you know, Traxxas introduces a new line of pinion gears just for you. These gears come machined out of hardened steel in large 32-pitch format for your most hardcore bashing needs. They are available for Slash and Stampede 4X4 models as well as brushed versions of E-Revo and E-Maxx etc.

89,-

Hovedbilde Traxxas 2455 Screws M4x24 Button-head Hex Socket (6)

Traxxas 2455 Screws M4x24 Button-head Hex Socket (6)

Traxxas 2455 Screws, 4x24mm button-head machine (hex drive) (6) Set of six 4x24 mm button-head machine screws with hex drive heads Replacement part for these models: Maxx® Slash®

39,-

Hovedbilde Fuse 49900 Traxxas Plug - Batteryside

Fuse 49900 Traxxas Plug - Batteryside

Traxxas Plug - Batteryside

29,-

Hovedbilde Traxxas 3458 Heat Sink for Velineon 3500 & 540XL

Traxxas 3458 Heat Sink for Velineon 3500 & 540XL

Traxxas Heat sink - fits #3351R (Velineon 3500) and #3461 (Velineon 540XL) brushless motors The 3458 heat sink fits Velineon brushless motors #3351R and #3461 when installed in 4X4 vehicles. (Does not fit 2WD configurations). For more information on installing the heatsink and fan shroud, read the following article.

129,-

Hovedbilde Traxxas 3456 Cooling Fan Kit

Traxxas 3456 Cooling Fan Kit

Cooling Fan Kit (Velineon 3500/ 540XL) (Need Heat Sink #3458

299,-

329,-

-9%

Hovedbilde Traxxas 2441A Camber Links

Traxxas 2441A Camber Links

Camber link set for Bandit (grey) (plastic/ non-adjustable)

39,-

Hovedbilde Traxxas 3195 Top Steel Drive Gear 22T Nitro Hawk

Traxxas 3195 Top Steel Drive Gear 22T Nitro Hawk

This is the 22 tooth, hardened steel top drive gear. Fits: Traxxas Rustler VXL/XL-5 Stampede VXL/XL-5 Bandit VXL/XL-5 1/10 Slash 2WD

39,-

Hovedbilde Traxxas 2530 Bulkhead Front Black

Traxxas 2530 Bulkhead Front Black

This is a Stock Replacement Front Bulkhead used in many Traxxas vehicles. The front suspension arm hinge pins pass through this piece. FEATURES: Black nylon construction INCLUDES: One front bulkhead REQUIRES: Nothing. This is a direct replacement part. SPECS: Length: 73.6mm (2.90") Width: 41mm (1.62") Height: 29mm (1.14") COMMENTS: This part is used on the following vehicles: Rustler, Bandit, Stampede, Nitro Rustler, SRT, Nitro Stampede, Rustler XL and Stampede XL.

79,-

Hovedbilde Traxxas 2422 Pinion Gear 22T 48P

Traxxas 2422 Pinion Gear 22T 48P

Gear, 22-T pinion (48-pitch) / with set screw

39,-

Hovedbilde

"Bulk" Traxxas 2531X Suspension Arms Front (2)

Denne erstatter TRX 2531 *** This is a Brand new item taken from a kit (chopped part), therefore will not have a Traxxas packaging *** "Bulk" Traxxas 2531X Suspension Arms Front (2) These are the Replacement Front Suspension Arms for many Traxxas kits. These are located on the front bulkhead and are held on by suspension pins. FEATURES: Nylon construction Black in color INCLUDES: Two black nylon suspension arms REQUIRES: Assembly onto kit. SPECS: Length: 3" Width: 1.2" COMMENTS: This will work on the Bandit, Nitro Stampede, Nitro Rustler, SRT, and the Nitro Sport.

129,-

Hovedbilde Yeah Racing MG-48023 Aluminum 7075 Hard Coated Motor ...

Hovedbilde Yeah Racing MG-48023 Aluminum 7075 Hard Coated Motor ...

Yeah Racing MG-48023 Aluminum 7075 Hard Coated Motor ...

Aluminum 7075 Hard Coated Motor Gear/Pinions 48 Pitch 23 Teeth The motor gear series including 2 major types of Pitch Pinion - the 48 Pitch Pinion and the 64 Pitch Pinion. The 48 Pitch Pinion available from 15 teeth to 38 teeth. The 64 Pitch Pinion available from 17 teeth to 52 teeth. The Yeah Racing Aluminum Motor Gear are made by 7075 high quality aluminum with titanium coated surface. Material: 7075 Aluminum Color: Titanium Teeth: 23 Set Screw (1 pc) How to calculate Final Gear Ratio? For example, if your car has the following setting: Motor Gear: 25 Spur Gear: 84 Pulley: 19 Gear Differential: 38 Firstly, we need to calculate the 'Motor Gear to Spur Gear Ratio', divide 84 by 25 equal to 3.36. Then we need to calculate the 'Pulley to Gear Differential Ratio', divide 38 by 19 equal to 2. Finally, the 'Final Gear Ratio' is 3.36 x 2 = 6.72. Motor Turn used based on Final Gear Ratio: 3.5T: 9.5-10 4.0T: 8.9-9.5 8.5T: 6.4-7.0 The above guideline is for reference only. The recommended motor turn may vary depending on different brands. More information can be found on motors' official websites. Review from RC Driver, Issue 108, December 2012 In electric RC, the pinion gear is meshed with the spur gear and provides power to drive train. A quality pinion gear will provide maximum transfer of speed and power to the motor. “I am a fan of precision manufactured, quality pinion gears that when properly meshed with a new or good spur are totally silent! These gears from Yeah Racing certainly fill the bill.” By Chris Kovachevich, RC Driver Issue 108, December 2012 Features: For: 1:10 EP, fit on 540 Motor Material: 7075 Aluminum Color: Titanium Specifications: Pitch: 48 Teeth: 23 Includes: 48 Pitch Pinion 23 Teeth (1 Pc) Set Screw (1 pc)

59,-

Hovedbilde RPM 73932 Adjustable Body Mounts Slash 4X4/Stampede ...

RPM 73932 Adjustable Body Mounts Slash 4X4/Stampede ...

Adjustable Height Body Mounts for the Traxxas Slash 4×4 & Stampede 4× Quick Notes: – replaces stock Traxxas #6815R – fits either front or rear location on the Slash 4×4 – fits the rear location on the Stampede 4×4 Description RPM Adjustable Height Body Mounts for the Traxxas Slash 4×4 & Stampede 4×4 are designed to give you optional body height positions where stock left you none. Our version of the Slash 4×4 body mount starts off lower than stock by 1/8” (or approx. 3.2mm). We supply a pair of molded spacers to allow you the option of a stock height body position using the thin spacer under the body mount. If monster suspension travel is needed or you just like the higher stance and larger wheel well openings a taller body mount provides, you can increase the height by 1/8” using the thicker of the two spacers. In extreme cases, both spacers may be used for a full 1/4”* (6.35mm) of extra body height. We weren’t solely going for looks either. RPM body mounts are just plain tough! We engineered new, larger ribs into the mounts to provide extra rigidity and support for the body while keeping weight to a minimum. We mold these body mounts in black from our proven-tough blend of engineering-grade materials, which provides extra durability and impact-resistance in the most extreme situations. What’s Included: Each kit contains two body posts, one body mount bracket, two spacers and two M3 x 16mm mounting screws. Two kits will be needed to complete one vehicle.

129,-

Hovedbilde Traxxas 6468 Tire Glue TRX Ultra Premium

Hovedbilde Traxxas 6468 Tire Glue TRX Ultra Premium

Traxxas 6468 Tire Glue TRX Ultra Premium

Traxxas Ultra Premium Tire Glue Ultra Premium Tire Glue (#6468) with packageOnly one tire glue is certified for use with the 100+mph XO-1: Traxxas Ultra Premium Tire Glue. The XO-1 relies on a high-strength tire bond to withstand incredible centrifugal forces at speeds in excess of 100mph. No other glue endures such high loads, which makes Traxxas Ultra Premium Tire Glue the ultimate adhesive for any tire and rim combination (and any other application that requires a high-strength bond). To preserve the maximum bonding power of Traxxas Ultra Premium Tire Glue, its bottle is specially designed to maintain a tight seal and prevent clogging. The bottle and nozzle are made of glue-resistant material, and a pin integrated into the tightly-fitting screw-on cap assures glue won't clog the bottle tip. The tip's fine opening allows precise glue application every time you reach for Traxxas Ultra Premium Tire Glue. Traxxas Ultra Premium Tire Glue is custom-blended exclusively for Traxxas. There simply is no better bond for high-speed, high-power vehicles. Traxxas Ultra Premium Tire Glue Features: The only glue Traxxas Certified for the 100+mph XO-1 Highest-quality cyanoacrylate (CA) glue available Fine tip opening for precise glue application Tightly-fitting cap with sealing pin Glue-resistant bottle and tip material Includes two precision application tips Content 20gr

139,-

159,-

-13%

Hovedbilde Zap PT09 Adhesives Zap CA 1/2 oz

Zap PT09 Adhesives Zap CA 1/2 oz

The ZAP CA Glues are clog-resistant with and have an extra, long tip to reach into tight spots. Easy-to-squeeze bottles aid in applying just the right amount of glue for easier sanding and less mess. Not safe for foam. For foam applications use epoxy or foam-safe CA. FEATURES Wicks quickly for instant bonds on tight-fitting parts. INCLUDES One ZAP CA Glue 1/2oz Thin COMMENTS Thin is instant setting: CA Thick is gap filling: CA+

79,-

Hovedbilde Traxxas 7173 Tires, Response Pro 2.2''

Traxxas 7173 Tires, Response Pro 2.2''

Tires, Response Pro 2.2" (soft-compound, narrow profile, short knobby design)/ foam inserts (2)

179,-

Hovedbilde Traxxas 7171 Wheels, dished 2.2'' (white)

Traxxas 7171 Wheels, dished 2.2'' (white)

Wheels, dished 2.2" (white) (2)

79,-

Hovedbilde RPM 80905 Mount for Rear Bumper or Wheelie Bar for 2WD ...

Hovedbilde RPM 80905 Mount for Rear Bumper or Wheelie Bar for 2WD ...

RPM 80905 Mount for Rear Bumper or Wheelie Bar for 2WD ...

RPM Mount for Rear Bumper or Wheelie Bar for 2WD Slash, Rustler, Stampede & Bandit - Blue Replaces Traxxas stock #3677 Quick Notes: Fits Traxxas 2WD Slash, Rustler, Stampede & Bandit Replaces Traxxas stock #3677 After hearing numerous requests to look into the rear bumper mount on the Traxxas Slash, we found several issues that could use the RPM touch. Those same problems were encountered on e-Rustler, e-Stampede & Bandit vehicles as well, using the stock wheelie bar mount. The problem – the stock mount uses only a single screw on the gear cover side to hold the mount in place. That causes a hinge effect under rear impacts causing the slotted area holding on to the rear skid plate to pop off after an impact, leaving the stock bumper / wheelie bar mount hanging under the chassis. The RPM solution… An all-new bumper mounting system that eliminates all of the problems encountered with the stock version. The RPM rear bumper / wheelie bar mount has two mounting holes on the gear cover side and three on the motor side – that’s two additional mounting points to eliminate that annoying hinge effect mentioned above. The additional mounting screws help disperse impact energy into the transmission case over more surface area, reducing the possibility of damaging the case significantly! The new RPM mount design means no more slotted parts hanging below the rear skid plate – ever! Our mount tucks up quite nicely behind the skid plate for better rear end ground clearance. Our rear bumper / wheelie bar mount fits a wide range of vehicles too. It fits all versions of the Traxxas Slash 2wd, electric Stampede, electric Rustler and Bandit including VXL, XL-5 and legacy versions. The RPM rear bumper / wheelie bar mount is molded in our nearly indestructible blend of nylons and is sold in either blue or black. Each mount comes with all necessary hardware, complete instructions for ease of installation and an industry-leading warranty to back it all up! Tech Notes: The RPM Rear Bumper Mount replaces Traxxas #3677.

139,-

Hovedbilde Traxxas 3767G Shock Caps Green

Traxxas 3767G Shock Caps Green

These are the Green Aluminum Shock Caps from Traxxas. FEATURES: Aluminum construction, green in color Fits all Traxxas Ultra Shocks INCLUDES: Four Shock Caps REQUIRES: Installation on the shocks

179,-

189,-

-5%

Hovedbilde Robinson Racing 7857 Steel Idler Gear ...

Robinson Racing 7857 Steel Idler Gear ...

This is the optional Robinson Racing Steel Idler Gear for the Traxxas 1/10 scale Slash 2WD. FEATURES: Constructed of hardened steel INCLUDES: Steel Idler Gear REQUIRES: Installing bearings from stock idler gear

299,-

Hovedbilde STRC ALUMINUM STEERING BELLCRANK SET (W/BEARINGS) ...

STRC ALUMINUM STEERING BELLCRANK SET (W/BEARINGS) ...

STRC ALUMINUM STEERING BELLCRANK SET (W/BEARINGS) FOR SLASH/RUSTLER/BANDIT (GM) CNC Machined Aluminum Steering Bellcrank system features a 3 piece design featuring single CNC machined solid aluminum main bellcrank, providing slop-free, precision steering response (unlike other 2 pieces bolt together design of other manufactures). Included: steering bellcrank set 4 pieces of bearings f

299,-

Hovedbilde RPM 81162 RPM Wide Front Bumper for 2WD Bandit, ...

Hovedbilde RPM 81162 RPM Wide Front Bumper for 2WD Bandit, ...

RPM 81162 RPM Wide Front Bumper for 2WD Bandit, ...

RPM Wide Front Bumper for 2WD Bandit, Rustler & Stampede - Black Replaces stock Traxxas #2735 Quick Notes: Fits the Electric Stampede, Electric Rustler, Bandit, Nitro Sport, Nitro Stampede & Nitro Rustler Replaces stock Traxxas #2735 Give your favorite Traxxas vehicle added protection with the RPM wide front bumper. This bumper stands six inches wide and adds an extra 1-1/2” worth of bulletproof, RPM protection to the front end of the vehicle. RPM designed this bumper with the backyard basher in mind by making it with our guaranteed unbreakable blend of nylons and is molded in black, blue, green and red. This bumper will help reduce front-end damage during head on collisions with curbs, trees, etc!

99,-

Hovedbilde Castle Creations CC Pinion 21T 48P - 5mm

Castle Creations CC Pinion 21T 48P - 5mm

Castle Creation Steel Pinion 21T - 48 Pitch - 5mm Bore Our CC PINION offerings are expanding and will include additional 1/10 scale applications! These mega-strength pinions are machined from carbon steel and will have a good resistance to wear and tear with their case-hardened finish. The result is a performance pinion that can take the extreme conditions large-scale RC cars operate in. Available in 20T, 21T, 22T, 23T, 24T, 25T, 26T, 27T, 28T, 29T, and 30T Our pinions use a 5mm bore Product designed in Olathe, Kansas USA Product made in China

179,-

Hovedbilde RC4WD F0030 - 4pc Precision Metric Hex/Nut Driver Set

Hovedbilde RC4WD F0030 - 4pc Precision Metric Hex/Nut Driver Set

RC4WD F0030 - 4pc Precision Metric Hex/Nut Driver Set

RC4WD 4pc Precision Metric Hex/Nut Driver Set Our RC4WD 4pc Precision Metric Hex/Nut Driver Set is designed to make life easier when working with miniature scale hex bolts which are often found on highly detailed wheels and parts. Get your set today! Specifications: Steel Tipped Drivers with Nylon Handles Chrome Plated Drivers for Durability Designed By RC4WD Handle Length: 2.75in / 70.0mm Total Weight: 2.20oz / 62.5g What's Included: 1x RC4WD 1.5 Precision Metric Hex/Nut Driver 1x RC4WD 2.0 Precision Metric Hex/Nut Driver 1x RC4WD 2.5 Precision Metric Hex/Nut Driver 1x RC4WD 3.0 Precision Metric Hex/Nut Driver Notes: Fits RC4WD Miniature Scale Hex Bolts (M1.6 x 4mm) (Silver) (Z-S1124) Fits RC4WD Miniature Scale Hex Bolts (M2 x 5mm) (Silver) (Z-S0624) Fits RC4WD Miniature Scale Hex Bolts (M2.5 x 6mm) (Silver) (Z-S0663) Fits RC4WD Miniature Scale Hex Bolts (M3 x 6mm) (Silver) (Z-S0639) Fits RC4WD Hex Head Bolts

249,-

329,-

-24%

Hovedbilde

"Utgått" Traxxas 6811R Body Slash 4x4 Heavy Duty Clear

Body, Slash 4X4, heavy duty (clear, untrimmed, requires painting)/ window masks/ decal sheet

509,-