Hopp til innhold
Hjem / Radio/Servo/Motor / Radioutstyr / Mottakere / Futaba Mottakere / Futaba R2106GF 6-Channel 2.4GHz S-FHSS Micro Receiver
-6%

Futaba R2106GF 6-Channel 2.4GHz S-FHSS Micro Receiver

Art.nr: R2106GF

499,-

529,-

- 6%
Futaba

Futaba
** Ikke på lager

Produktet er midlertidig utsolgt. Dersom du ønsker å motta en epost når vi får det inn på lager, kan du legge igjen epostadressen din i skjemaet under.

Informasjon

This is the Futaba R2106GF 2.4GHz FHSS 6-Channel Micro Receiver.

FEATURES: Compatible with all Futaba FHSS/S-FHSS transmitters
            **Not compatible with FASST systems**
          Normal and High-Speed Modes:
             Normal mode frame rate is (FHSS/S-FHSS) 13.63ms and accepts any
               type of servos or peripherals.
          High-Speed mode (in 4PL tx only), with an output of 6.8ms accepts
               digital servos including the BLS series and most peripheral
               equipment such as brushless ESCs
   

INCLUDES: Futaba R2106GF 2.4GHz FHSS 6-Channel Micro Receiver with Instructions

REQUIRES: Installing in aircraft and connecting battery and servos

SPECS:    Size: 1.5 x .85 x .40" (38 x 21 x 10mm)
          Weight with Case: 0.14oz (4g)

Produsent

Futaba

Futaba

Kunder kjøpte også

Hovedbilde Bronto 6,0V 3300mAh - RX Hump Pack - Ni-Mh
Bronto 6,0V 3300mAh - RX Hump Pack - Ni-Mh
Bronto 6,0V 3300mAh - RX Hump Pack - Ni-Mh Mottakerpakke(Hump pack) for bruk i store biler. Passer f.eks perfekt i HPI Baja-modellene. På batteripakken er det både Tamiyatilkobling for hurtiglading, og std. servotilkobling for bruk som RX pakke.   Høyde 45mm Bredde 70mm Lengde 45mm Ledningslengde    10cm Kapasitet 3300mAh Volt 6.0V Tilkobling Tamiya og servokabel Lading: Max 1A

349,-

KJØP
Hovedbilde Dynomax 9234 Wire Red & Black 16AWG D1.6/3mm x 1m
Dynomax 9234 Wire Red & Black 16AWG D1.6/3mm x 1m
D-MAX Wire Set Red & Black - 16AWG 1+1m This is a high quality wire with a high amount of copper strands making it very suitable for RC models and other hobby projects. The wire is covered with a silicone based insulation material and together with the high strand count it’s also very flexible.   Short and Thick is Good In electric high powered models we are recommending you to use short and as thick wires as possible (within reason) together with a matching diameter/area connector system for optimum performance. Specifications: Length: 1+1m AWG Wire: 16 Area Wire: 1.5mm2 Diameter Wire: 1.6mm Diameter Insulation: 3mm Wire: 252 Strands of Copper @ 0.08 mm Insulation: Silicone Based

39,-

KJØP
Hovedbilde Dynomax 9533 Connector Tamiya Pair
Dynomax 9533 Connector Tamiya Pair
Connector Tamiya Pair

25,-

35,-

KJØP
-29%
Hovedbilde Power HD LW-20MG Waterproof Servo 20kg/0.16s
Power HD LW-20MG Waterproof Servo 20kg/0.16s
The Power HD LW-20MG is the latest servo that features an all-aluminum case, copper and aluminum gears, a powerful coreless motor and it pulls up to 20kg-cm of torque at a speed of 0.16s. The standard sized servo is also waterproof making this a great servo for crawlers, 1/8 scale trucks and buggies. It comes black anodized and with laser-etched graphics.   Spesifications: Torque(4.8V): 18.0 kg-cm (250.0 oz/in) Torque(6.0V): 23.0 kg-cm (319.4 oz/in) Speed: 0.14 sec (4.8V) ? 0.12 sec (6.0V) Operating Voltage 4.8 ~ 6.0 DC Volts Weight: 60.0 g (2.12 oz) Bearing Type Ball Bearing x 2 Motor Type Coreless Motor Gear Type Copper & Aluminum Working frequence 1520 s / 333hz Size: 40.7 x 20.5 x 39.5 mm ( 1.6 x 0.80 x 1.55 in)

449,-

539,-

KJØP
-17%
Hovedbilde Futaba Receiver R304SB-E 4CH T-FHSS Car - Internal ... Hovedbilde Futaba Receiver R304SB-E 4CH T-FHSS Car - Internal ...
Futaba Receiver R304SB-E 4CH T-FHSS Car - Internal ...
Futaba R304SB-E T-FHSS Receiver A new small and light 4 channel T-FHSS 2.4GHz receiver with telemetry (sensors available separately and are connected through the S.BUS2 port). The R304SB-E receiver has no external antenna so it's recomended for electric cars only.   T-FHSS 2.4GHz (Telemetry) receiver for T4PV, T4PM, T4PLS, T4GRS, T4PX & T4PX-R Internal antenna (for electric cars) Size: L35 x W23.3 x H8.5/12.5 mm Weight: 6.7 g Power: 4.8-7.4V batteries (Voltage range: 3.5-8.4V) Spec. Frequency: 2,4GHz Signal system: T-FHSS Length: 35 mm Height: 12,5 mm Width: 23,3 mm Input Voltage: 4,8-7,4 V Channels: 4 Special Functions: High Voltage , S.Bus , S.Bus2

749,-

799,-

KJØP
-6%
Hovedbilde YR YB0328MX RC Ball Bearing Set With Bearing Oil For ... Hovedbilde YR YB0328MX RC Ball Bearing Set With Bearing Oil For ...
YR YB0328MX RC Ball Bearing Set With Bearing Oil For ...
RC BALL BEARING SET WITH BEARING OIL FOR AXIAL SCX24 Description: This is Yeah Racing RC Ball bearings should always be your first upgrades, it reduces friction for less rolling resistance, and that means higher speed and longer running times. RC Ball bearings hardly require maintenance and last a lot longer than stock Oilite bushings. Feature: Material: Steel Shielding: Rubber Include: Bearing 20 pcs  YB6031M 2mmx5mmx2.5mm(2pcs) YB6005M 2mmx6mmx2.5mm(16pcs) YB6009M 4mmx8mmx3mm(2pcs) YA-0215 Bearing Oil (1pc)

219,-

239,-

KJØP
-8%
Hovedbilde Yeah Racing YA-0357 1/10 RC Rock Crawler Accessory ... Hovedbilde Yeah Racing YA-0357 1/10 RC Rock Crawler Accessory ...
Yeah Racing YA-0357 1/10 RC Rock Crawler Accessory ...
Yeah Racing 1/10 RC Rock Crawler Accessory 96cm Long Chain and Hook Set Red Description: This is Yeah Racing 1/10 RC Rock Crawler Accessories 96cm Long Chain and Hook Set Red.           Feature: For: 1/10 RC Material: Steel Color: Red and Silver   Specification: Length: 96 cm   Include: Yeah Racing 1/10 RC Rock Crawler Accessories 96cm Long Chain and Hook Set Red (1 pc)

59,-

69,-

KJØP
-14%
Hovedbilde Axial 201001 Front Bumper 2019 Jeep Wrangler JLU CRC
Axial 201001 Front Bumper 2019 Jeep Wrangler JLU CRC
Compatible Products Front Bumper: SCX24 CRC JL. Includes two LED lights with wiring harness. Axial Front Bumper: 2019 Jeep Wrangler JLU CRC AXI201001 is compatible with AXI00002T1, AXI00002T2

115,-

KJØP
Hovedbilde Yeah Racing TRX4-055 Plastic Power Switch For Traxxas ... Hovedbilde Yeah Racing TRX4-055 Plastic Power Switch For Traxxas ...
Yeah Racing TRX4-055 Plastic Power Switch For Traxxas ...
Yeah Racing Plastic Power Switch For Traxxas TRX-4  #TRX4-055 Description: Hate taking off the body to switch your Traxxas esc on or off? Use this extension for the button for easy power up and down. The lever tucks neatly underneath the rock slider and will not come into contact with rocks for accidental power downs.   Feature: For: Traxxas TRX-4 TRX-6 Material: Plastic Color: Black/Red Include: Switch Extension (1 pc) Mounting Tape (2 pcs) Mounting Hardware (1 pack)

109,-

KJØP
Hovedbilde Multiplex SERVO MS8510MG DIGITAL
Multiplex SERVO MS8510MG DIGITAL
Multiplex SERVO MS8510MG DIGITAL Perfekt servo for indoor fly. Eventuelt fly av micro størrelse. Med sin lille fysiske størrelse 8x23x20mm – OG sine beskjedene 5gr Informasjon på engelsk: The new multiplex indoor servo. The MS-8510MG Digital is specially designed to meet the needs of indoor pilots. It’s fast, strong, and precise. Has a sturdy aluminum gear. (Finally no more “caries” after a contact with the ground, as with so many other micro servos with plastic gears) An extra large servo lever is perfect for rope and rod linkage. Last but not least, thanks to the “honest” 60 degree path, large deflections are possible at full power. Look forward to many nice flights with the new MS-8510MG Digital The MS-8510Mg Digital is also perfect for F3K, HLG and other models. Bredde: 8 mm Høyde: 23mm Lengde: 20mm Vekt: 5gr Servotype: Mikro Spesielle funksjoner: digital Gear: metall Driftsspenning i V: 4,8-6,0 V. Posisjoneringstid s / 60 ° ved 6,0 ​​volt: 0,06 Moment i kg/cm ved 6,0 ​​volt: 1 Tanning: 5 Kulelager: Nei. Vanntett: Nei DREV Metall HASTIGHET 0.06 MERKE Multiplex SPENNING 4.8V, 6.0V SPLINE 15 STØRRELSE Nano TIL Fly TORQUE 1kg TYPE Digital VEKT 5g

269,-

KJØP
Hovedbilde MULTIPLEX POWER UNIT V2 EXTRA 330 SC AND FUNNYCUB ...
MULTIPLEX POWER UNIT V2 EXTRA 330 SC AND FUNNYCUB ...
MULTIPLEX POWER UNIT V2 EXTRA 330 SC AND FUNNYCUB INDOOR EDITION Motorsett til Extra 330SC og FunnyCub fra Multiplex Innehold: – ROXXY C27-13-1880kV – ROXXY BL-Control 715-BEC – Propeller GWS EP-8x4HD – Propell Adapterring aluminium 5/7mm MERKE Multiplex PRODUKT Motorsett TIL Fly TYPE Børsteløs

899,-

KJØP
Hovedbilde Savox SB-2273SG
Savox SB-2273SG "High Torque" Brushless Steel Gear ...
This is the Savox SB-2273SG High Torque Brushless Steel Gear Digital Servo. Features: •Combines leading edge technology with super high 12 bit (4096) resolution and unique steel gears. •Super light-weight. •Brushless motor provides extremely high speed, high torque, incredible efficiency, and amazingly low power consumption. •The full aluminum case design not only looks good but also allows for cooler and smoother operating temps. •Totally green – from materials to production, these servos are environmentally friendly. •Ideal for 1/8th or 1/10th scale trucks and buggies (electric & nitro) and giant scale aircraft. Also suitable for use in boats and helis. *NOTE: Certain combinations of receiver and ESC have been found to cause "Brown Out" issues when combined with Savox servos. An external BEC, or BEC stabilizing receiver capacitor may be needed for efficient, glitch free operation in low voltage electric applications.   Specifications: • Speed: ◦ @7.4V: .095 sec/60 ◦ @6.0V: .12 sec/60 • Torque: ◦ @7.4V: 28 kg-cm ◦ @6.0V: 23 kg-cm • Dimensions: 40.3x20.2x38.5mm • Weight: 69.0g • Gear: Unique Steel • Bearing: 2BB • Case: Full Aluminum • Spline: 25 Tooth

1.195,-

KJØP
Hovedbilde RPM 73852 Axial Yeti XL Front Lower A-arms – Black
RPM 73852 Axial Yeti XL Front Lower A-arms – Black
Quick Notes: – replaces stock Axial #AX31018 – removes as much as 0.004″ (0.01mm) of slop from the inner and outer hinge pins – more a-arm clearance at the bellcrank for less possibility of center-link damage from full suspension compression.   Description The Axial Yeti XL is a monster of a truck! With that much power and weight, the demands on the front suspension components are extreme. With extreme demand, there’s only one place to look for the ultimate in aftermarket replacements – RPM! Each RPM A-arm is designed from the ground up to survive what was previously unsurvivable. Massive support beams off to either side provide the support while 30° leading and trailing edges help improve transitions across ultra rugged terrain. To help improve suspension tuning and reduce slop, we sized the hinge pin holes accurately, removing as much as 0.004” (0.1mm) of slop from the inner and outer hinge pins (see “Tech Notes” below for additional slop notes). Additional A-arm clearance around the bellcrank center-link allow for more up-travel without the severe impact the stock A-arms and center-link encounter at full suspension up-travel, reducing the likelihood of a broken center-link. All RPM A-arms are molded from our ultra-durable blend of engineering grade nylons and backed by our limited lifetime warranty against breakage. With RPM on-board, your time on the trail will be time behind the wheel and not on the bench! Tech Notes: RPM Yeti XL A-arms replace stock Axial #AX31018. The Yeti XL we reviewed had A-arm hinge pins holes that were roughly .004” (0.1mm) – .005” (0.13mm) oversized from nominal. Furthermore, the hinge pins were roughly 0.005” (.13mm) undersized as well, creating as much as .01” (0.25mm) of combined suspension slop. Nominal sizes are 0.118” (3mm) and 0.1575 (4mm). RPM recommends checking your hinge pins for size and replacing them with on-sized pins (not available through RPM) for dramatically improved suspension performance above and beyond the improvements created when installing RPM A-arms.

249,-

KJØP
Hovedbilde Axial 31034 WB XL Driveshaft Yeti
Axial 31034 WB XL Driveshaft Yeti
This is the WB XL Driveshaft for the Axial Yeti XL Rock Racer. FEATURES Two-piece composite plastic construction INCLUDES WB XL Driveshaft

149,-

KJØP
Hovedbilde RPM 81712 Front Shock Tower Yeti XL replaces AX31025
RPM 81712 Front Shock Tower Yeti XL replaces AX31025
This is the optional RPM Front Shock Tower for the Axial Yeti XL. Quick Notes: – replaces stock Axial #AX31025 FEATURES Constructed of a blend of engineering grade nylons  The new design adds support to camber link ears and upper shock mounts INCLUDES RPM Front Shock Tower for the Axial Yeti XL

129,-

KJØP
Hovedbilde Axial 31017 Steering Knuckle Set Yeti XL
Axial 31017 Steering Knuckle Set Yeti XL
This is the XL Steering Knuckle Set for the AX90032 Axial Yeti XL     FEATURES Plastic construction, black in color   INCLUDES One each Left and Right Steering Knuckles

149,-

KJØP
Hovedbilde JPerkins 5507906 9stk Vingestrikk 150mm
JPerkins 5507906 9stk Vingestrikk 150mm
Vingstrikk 150mm 9 stk i pose Gummistrikker til modellfly

39,-

KJØP
Hovedbilde SAVÖX SB-2292SG Servo 50Kg 0.055s 8.4V Alu Brushless ... Hovedbilde SAVÖX SB-2292SG Servo 50Kg 0.055s 8.4V Alu Brushless ...
SAVÖX SB-2292SG Servo 50Kg 0.055s 8.4V Alu Brushless ...
SAVÖX SB-2292SG - High Voltage Brushless Steel-Geared Monster Torque Servo The powerful "Monster" performance series from Savox utilize an all aluminum case, unique brushless motor and controller technology to boost power up to 35% over previous generation servos. Features: High Voltage Full Aluminum Case 3 Precision Ball Bearings Unique steel gears Specifications: Torque @ 6V: 27kg/cm Torque @ 7.4V: 36kg/cm Torque @ 8.4V: 50kg/cm Speed @ 6V: 0.085 sec/60 deg Speed @ 7.4V: 0.07sec/60 deg Speed @ 8.4V: 0.055sec/60 deg Dimensions L x W x H: 40.3 x 20.2 x 38.7mm Technical Details: Operating Temperature: -10° to 50°C Running Current (no load): 180mA @6.0V, 220mA @7.4V Stall Current (at locked): 7500mA @6.0V, 9200mA @7.4V Idle Current: 5mA @4.8V, 5mA @6.0V Wire Length: 300 +/- 5mm Output Gear Spline: 25 Tooth Bearings: 3BB Operating Travel: 100° (1000 → 2000 µ second) Neutral Position: 1500 µ second Pulse Width Range: 800 → 2200 µ second Maximum Travel: Appx 130° (900 → 2100 µ second) Refresh Rate: 333 Hz Motor Type: Brushless

1.895,-

1.995,-

KJØP
-5%
Hovedbilde Carson 907185 1:14 cross brace trailer hitch for ...
Carson 907185 1:14 cross brace trailer hitch for ...
1:14 cross brace trailer hitch for MB1850L

349,-

KJØP
Hovedbilde Tamiya 56335 1/14 Mercedes-Benz Actros 1851 Hovedbilde Tamiya 56335 1/14 Mercedes-Benz Actros 1851
Tamiya 56335 1/14 Mercedes-Benz Actros 1851
This is the electric powered, radio controlled, 1/14 scale    Tamiya Mercedes Benz Actros 1851 GigaSpace Tractor Truck kit with Body             Compatible with the Tamiya Tractor Truck Option Parts                          for further customization. FEATURES: Chassis: Ladder frame with aluminum channels and resin cross members           Body: ABS molded plastic           Drive Train: Two solid axle semi           Cabin: Tilt forward operation just like full-size truck, removable             fenders to depict a low carrying load           Drive: Shaft driven from front mounted motor to rear axles which are             equipped with differentials           Motor: RS540 brushed           Pinion Gear: 10 tooth           Transmission: Three speed servo controlled constant mesh           Suspension: Die cast metal front axle and reinforced resin rear             axles float mounted on metal leaf springs and coil spring shocks           Cabin: Molded plastic, white in color tilts forward separately from             fenders, clear plastic windows, separate grille, mirrors and             other accessories add to realism           Wheels: Chrome plated plastic           Tires: Six, treaded rubber radial INCLUDES: 1/14 scale Tamiya Mercedes Benz Actros, 540 motor, tires, wheels,             interior detail, ABS body, decal sheet, 3-speed transmission, and             instructions REQUIRES: Radio: 4-channel with 4-channel receiver and analog or digital trim             function           Servos: Two standard size for steering and shifting           Electronic Speed Control: Tamiya TEU302BK recommended, do             not use the Tamiya TEU101BK or the TEU104BK           Battery: 6-cell stick           Battery Charger: Timed or peak for 6-cell battery           Paint, building & track equipment SPECS:    Length: 18.03" (458mm)           Width:   7.7" (195mm)           Height: 12"   (305mm)           Gear Ratio: Low Gear 1:32.49                       2nd Gear 1:17.66                       3rd Gear 1:10.66

4.595,-

5.795,-

KJØP
-21%
Hovedbilde Carson 13516 Styrestag
Carson 13516 Styrestag

139,-

149,-

KJØP
-7%
Hovedbilde Axial AX31144 AE-5 Waterproof ESC w/Reverse & Drag ...
Axial AX31144 AE-5 Waterproof ESC w/Reverse & Drag ...
plug. Currently has star plug. This is the Axial AE-5 Waterproof ESC with Reverse.       FEATURES 3S LiPo capable Settings can be easily switched between LiPo and NiMH batteries with a simple jumper Jumper 1 switches between LiPo and NiMH batteries Jumper 2 switches drag brake settings Waterproof design Laser etched heat sink     INCLUDES Axial AE-5 ESC with Star Plug and Instruction Sheet     SPECIFICATIONS Input Voltage: 2-3S LiPo, 5-9 cell NiMH/NiCd Motor Limit: 12T 2S, 18T 3S On Resistance FET: .002 Rated/Peak Current: 180A Braking Current: 90A BEC Voltage / A: 5.0V 2/0A peak PWM Frequency: 1KHz Dimensions: 1.8 x 1.3 x 1.1" (46.5 x 34 x 28.5mm) Weight: 2.5oz (70g)     COMMENTS Due to running change, ESC no longer has power switch or Tamiya

749,-

KJØP
Hovedbilde Tamiya 85029 Spray Lacquer TS-29 Semi-Gloss Black 3 oz
Tamiya 85029 Spray Lacquer TS-29 Semi-Gloss Black 3 oz
This is a 100ml Spray Can of Synthetic Lacquer Paint from Tamiya. FEATURES: Cures in a short period of time.           Extremely useful for painting large surfaces.           100ml is enough to fully cover two or three 1/24 scale sized car             bodies.           Tamiya spray paints are not affected by acrylic or enamel paints.             Therefore, following the painting of the entire assembly, details             can be added or picked out using enamel and/or acrylic paints.  By             combining three different paints, the decoration of plastic             models will become simpler and more effective.           Available in 52 colors. INCLUDES: One 100ml Spray Can of Synthetic Lacquer Semi-Gloss Black Paint. REQUIRES: Eye, Lung and Skin Protection. COMMENTS: Highly Flammable, Pressurized Container.           Keep out of the reach of children.

109,-

KJØP
Hovedbilde Traxxas 5858 Springs Rear White Slash (2)
Traxxas 5858 Springs Rear White Slash (2)
These are the Rear Shock Springs for the Traxxas Slash FEATURES: Metal construction           White in color INCLUDES: Two Shock Springs REQUIRES: Installation on the Traxxas Slash SPECS:    Length, uncompressed: 69.5mm (2.74")           Wire Diameter: 1.4mm (0.05")           Inner Diameter: 15.5mm (0.61")  

59,-

KJØP
Hovedbilde Traxxas 2428 12T 48P Pinion Gear/Set Screw
Traxxas 2428 12T 48P Pinion Gear/Set Screw
 This is the 12T 48P Pinion Gear for the               Telluride Off-Road Vehicle from Traxxas FEATURES: Hardened steel construction   INCLUDES: 12T 48P Pinion Gear with Set Screw

39,-

KJØP

SamiRC Norge AS

© 2026 SamiRC Norge AS - Powered by Mystore.no

Om oss

  • SamiRC Norge AS
  • Nils Lauritssøns vei 34
  • 0870 OSLO
  • Org. nr. MVA 928 644 979 Foretaksregisteret
  • Tlf: 46760019
  • post@samirc.no

Kundeservice

Nyhetsbrev

  • klarna-dark.png
  • vipps-orange.png
  • mastercard-full.png
  • visa.png
  • paypal.png