Hopp til innhold
Hjem / Reservedeler/Option-parts / Reservedeler Bil / Pinion(drev til motor) / 48-pitch 3.17mm / Traxxas 2428 12T 48P Pinion Gear/Set Screw

Traxxas 2428 12T 48P Pinion Gear/Set Screw

Art.nr: TRX 2428

39,-

Traxxas

Traxxas
På lager: 2

Produktet er midlertidig utsolgt. Dersom du ønsker å motta en epost når vi får det inn på lager, kan du legge igjen epostadressen din i skjemaet under.

Informasjon

 This is the 12T 48P Pinion Gear for the
              Telluride Off-Road Vehicle from Traxxas

FEATURES: Hardened steel construction

 

INCLUDES: 12T 48P Pinion Gear with Set Screw

Produsent

Traxxas

Traxxas

Dette er den beste merket for RC-BIL i hele Norge, nei vi kan vel si hele verden uten å trenge å være redd for at vi sier noe galt!

Kunder kjøpte også

Hovedbilde Traxxas 2362 Shock Rebuild Kit
Traxxas 2362 Shock Rebuild Kit
This is a shock rebuild kit for 2 Traxxas black plastic shocks.  Includes: 4 E-clips   2 C-clips   2 O-rings   8 Washers   2 Diaphrams

35,-

KJØP
Hovedbilde RPM 80472 Rod Ends Short Black 1/10 Traxxas
RPM 80472 Rod Ends Short Black 1/10 Traxxas
Short Rod Ends for most Traxxas 1:10 Scale Vehicles Quick Notes: – RPM short rod ends replace Traxxas stock #5347 – requires stock Traxxas pivot balls Description The same engineering that made RPM Rod Ends for Associated and Losi vehicles some our best selling RPM parts for over 2 decades has gone into the creation of RPM Rod Ends for Traxxas 1/10th scale vehicles. These rod ends are tough! The area around the ball stud is thicker than the stock rod end while still allowing a full range of motion of the pivot ball. Additionally, the shank has been redesigned with a pair of flats, making the rod end much easier to work with (versus the stock, round shank). RPM rod ends are sold in sets of twelve to complete most vehicle needs. RPM Rod Ends cover a wide range of currently available Traxxas vehicles including all versions of the following: Slash 2wd, Slash 4×4, Summit, T-Maxx, E-Maxx, Revo, e-Revo, Slayer Pro 4×4, Stampede 4×4, Rustler VXL, Jato and Bandit VXL. Tech Notes: RPM short rod ends replace Traxxas stock #5347. Sold without pivot balls. Stock Traxxas pivot balls are required for completion.    

119,-

KJØP
Hovedbilde
"Bulk" Traxxas 5116 Ball Bearings 5x11x4mm (2)
*** This is a Brand new item taken from a kit (chopped part), therefore will not have a Traxxas packaging *** Disse lagerene er samme størrelse som Tamiya 1150 This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Cars. FEATURES: Metal bearing construction           Blue rubber dirt shields INCLUDES: (2) 5X11mm ball bearings, Part #5116 SPECS:    Inside diameter:      3/16"      (5mm)           Outside diameter:     7/16"     (11mm)           Width:                5/32"      (4mm)

39,-

55,-

Ikke på lager
-29%
Hovedbilde Yeah Racing DDL-100BK 100mm Desert Lizard Two Stage ... Hovedbilde Yeah Racing DDL-100BK 100mm Desert Lizard Two Stage ...
Yeah Racing DDL-100BK 100mm Desert Lizard Two Stage ...
Yeah Racing 100mm Desert Lizard Two Stage Internal Spring Damper Pair Black For Crawler #DDL-100BK Description: Introducing the Yeah Racing Desert Lizard internal spring shock for crawlers, comes pre-assembled for easy upgrading your current rig! Comes with a full set of springs and machined pistons for you to setup your rig for all sorts of different conditions! Included are springs for you to build either a droop or a sprung setup, a sprung setup will create a rig which will generate a lot of flex and more suspension travel. For the droop setup, your rig will sit lower and because of a spring under the piston, will be less prone to rolling over but will generate less flex. Featuring a triple O-Ring sealing cartridge which will prevent shock oil leakage!   Feature: For: HPI Crawler King / Gmade R1 KOMODO / Vaterra K5 / AXIAL SCX10 / RC Crawlers Material: Aluminum   Include: Yeah Racing 100mm Desert Lizard Two Stage Internal Spring Damper (2 pcs) Springs (16 pcs) Pistons (8 pcs) Mounting Hardware (1 pack)

339,-

399,-

KJØP
-15%
Hovedbilde Traxxas 5116 Ball Bearings 5x11x4mm Revo (2)
Traxxas 5116 Ball Bearings 5x11x4mm Revo (2)
Disse lagerene er samme størrelse som Tamiya 1150 This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo. FEATURES: Metal bearing construction           Blue rubber dirt shields INCLUDES: (2) 5X11mm ball bearings, Part #5116 SPECS:    Inside diameter:      3/16"      (5mm)           Outside diameter:     7/16"     (11mm)           Width:                5/32"      (4mm)

49,-

55,-

KJØP
-11%
Hovedbilde 3mm (1/8) Thick Silicone Fuel Tube 1 meter
3mm (1/8) Thick Silicone Fuel Tube 1 meter
3mm (1/8) Thick Silicone Fuel Tube 1 meter lang.

49,-

KJØP
Hovedbilde Traxxas 5260 Air Filter Housing T-Maxx
Traxxas 5260 Air Filter Housing T-Maxx
This is the Traxxas Air Filter Housing for the T-Maxx 2.5.  This attaches to the throat of the carburetor.     FEATURES Black plastic air filter housing with cover screen and  and changeable element  Rubber angled neck for filter  Rubber adapter for filter  Zip tie for fastening   INCLUDES One screened filter  One rubber straight neck  One rubber adapter  One zip tie   REQUIREMENTS TRX 2.5 engine or any carburetor that has a 14mm or 13mm outer carb  throat opening   SPECIFICATIONS  Diameter: 1.5" (39mm)  Height: 2.4" (60mm) including rubber adapter  Diameter of carb adapter: 0.53" (13.5mm)  Length of zip tie: 4.7" (120mm)

145,-

KJØP
Hovedbilde Traxxas 5261 Air Filter Foam Inserts Oiled (3)
Traxxas 5261 Air Filter Foam Inserts Oiled (3)
This is a package of three Air Filter Foam Inserts for the Traxxas 2.5 engine and 3.3 FEATURES Constructed of foam and pre-oiled to trap dirt INCLUDES Three Air FIlter Inserts for the Traxxas 2.5 and 3.3 engine REQUIREMENTS Installing in air filter boot on engine SPECIFICATIONS Height: 0.87" (22mm) Diameter: 0.98" (35mm)

79,-

89,-

KJØP
-11%
Hovedbilde Yeah Racing MG-48017 Aluminum 7075 Hard Coated Motor ... Hovedbilde Yeah Racing MG-48017 Aluminum 7075 Hard Coated Motor ...
Yeah Racing MG-48017 Aluminum 7075 Hard Coated Motor ...
Aluminum 7075 Hard Coated Motor Gear/Pinions 48 Pitch 17 Teeth The motor gear series including 2 major types of Pitch Pinion - the 48 Pitch Pinion and the 64 Pitch Pinion. The 48 Pitch Pinion available from 15 teeth to 38 teeth. The 64 Pitch Pinion available from 17 teeth to 52 teeth. The Yeah Racing Aluminum Motor Gear are made by 7075 high quality aluminum with titanium coated surface.  Material: 7075 Aluminum Color: Titanium Teeth: 17 Set Screw (1 pc)   How to calculate Final Gear Ratio? For example, if your car has the following setting: Motor Gear: 25 Spur Gear: 84 Pulley: 19 Gear Differential: 38 Firstly, we need to calculate the 'Motor Gear to Spur Gear Ratio', divide 84 by 25 equal to 3.36. Then we need to calculate the 'Pulley to Gear Differential Ratio', divide 38 by 19 equal to 2. Finally, the 'Final Gear Ratio' is 3.36 x 2 = 6.72.   Motor Turn used based on Final Gear Ratio: 3.5T: 9.5-10 4.0T: 8.9-9.5 8.5T: 6.4-7.0 The above guideline is for reference only. The recommended motor turn may vary depending on different brands. More information can be found on motors' official websites.   Review from RC Driver, Issue 108, December 2012 In electric RC, the pinion gear is meshed with the spur gear and provides power to drive train. A quality pinion gear will provide maximum transfer of speed and power to the motor. “I am a fan of precision manufactured, quality pinion gears that when properly meshed with a new or good spur are totally silent! These gears from Yeah Racing certainly fill the bill.” By Chris Kovachevich, RC Driver Issue 108, December 2012   Features: For: 1:10 EP, fit on 540 Motor Material: 7075 Aluminum Color: Titanium   Specifications: Pitch: 48 Teeth: 17   Includes: 48 Pitch Pinion 17 Teeth (1 Pc) Set Screw (1 pc)

59,-

KJØP
Hovedbilde Pro-Line 639200 Big Bore Scaler Shocks (4) for TRX-4M Hovedbilde Pro-Line 639200 Big Bore Scaler Shocks (4) for TRX-4M
Pro-Line 639200 Big Bore Scaler Shocks (4) for TRX-4M
Pro-Line 639200 Big Bore Scaler Shocks (4) for TRX-4M

549,-

Hovedbilde Traxxas 5525 Rod Ends/Hollow Balls
Traxxas 5525 Rod Ends/Hollow Balls
These are the Rod Ends and Balls for the Traxxas Slash 4x4 and other Traxxas cars. FEATURES: Black nylon construction.           Steel hollow balls. INCLUDES: Twelve rod end/balls REQUIRES: Installing on Jato SPECS:   Length: 1-1/8" (28mm)          Width: 3/8" (9mm)  

119,-

129,-

KJØP
-8%
Hovedbilde Traxxas 9736 Skidplate Center, Bumper Mount F&R TRX-4M
Traxxas 9736 Skidplate Center, Bumper Mount F&R TRX-4M
Skidplate Center, Bumper Mount F&R TRX-4M Skidplate, center/ bumper mount, front/ bumper mount, rear Center skid plate with front and rear bumper mounts

59,-

79,-

KJØP
-25%
Hovedbilde Traxxas 9741 Axle Housing Front & Left TRX-4M
Traxxas 9741 Axle Housing Front & Left TRX-4M
Axle housing, front & rear Front and rear axle housings (Case only - no internal parts)

59,-

79,-

KJØP
-25%
Hovedbilde Traxxas 5349 Rod Ends w/Hollow Balls Small Revo (6)
Traxxas 5349 Rod Ends w/Hollow Balls Small Revo (6)
            This is the Small Rod End Set for the Traxxas Revo. FEATURES: Plastic construction           Black in color           Metal Pivot Balls INCLUDES: Six Rod Ends           Six Pivot Balls REQUIRES: Assembly to vehicle SPECS:    Length:               18mm (.71")           Width at ball joint: 9.5mm (.38")

49,-

KJØP
Hovedbilde Traxxas 6745 Gear 32P 9T
Traxxas 6745 Gear 32P 9T
This is a 9 Tooth 32 Pitch Pinion Gear for the Traxxas. FEATURES: Machined Steel Designed for a 3mm shaft INCLUDES: One 9 tooth Pinion Gear One 3 x 4mm Set Screw

45,-

55,-

KJØP
-18%
Hovedbilde HPI 85259 Racing Drive Gear Set Wheely King
HPI 85259 Racing Drive Gear Set Wheely King
These are the Drive Gears for the HPI Wheely King. FEATURES: Plastic Construction Black in Color INCLUDES: (1) Drive gear set(4 gears) REQUIRES: Installation       (11)

129,-

KJØP
Hovedbilde Yeah Racing MG-48015 Aluminum 7075 Hard Coated Motor ... Hovedbilde Yeah Racing MG-48015 Aluminum 7075 Hard Coated Motor ...
Yeah Racing MG-48015 Aluminum 7075 Hard Coated Motor ...
Aluminum 7075 Hard Coated Motor Gear/Pinions 48 Pitch 15 Teeth Description: The motor gear series including 2 major types of Pitch Pinion - the 48 Pitch Pinion and the 64 Pitch Pinion. The 48 Pitch Pinion available from 15 teeth to 38 teeth. The 64 Pitch Pinion available from 17 teeth to 52 teeth. The Yeah Racing Aluminum Motor Gear are made by 7075 high quality aluminum with titanium coated surface. Material: 7075 Aluminum Color: Titanium Teeth: 15 Set Screw (1 pc)     How to calculate Final Gear Ratio? For example, if your car has the following setting: Motor Gear: 25 Spur Gear: 84 Pulley: 19 Gear Differential: 38 Firstly, we need to calculate the 'Motor Gear to Spur Gear Ratio', divide 84 by 25 equal to 3.36. Then we need to calculate the 'Pulley to Gear Differential Ratio', divide 38 by 19 equal to 2. Finally, the 'Final Gear Ratio' is 3.36 x 2 = 6.72.   Motor Turn used based on Final Gear Ratio: 3.5T: 9.5-10 4.0T: 8.9-9.5 8.5T: 6.4-7.0 The above guideline is for reference only. The recommended motor turn may vary depending on different brands. More information can be found on motors' official websites.     Review from RC Driver, Issue 108, December 2012 In electric RC, the pinion gear is meshed with the spur gear and provides power to drive train. A quality pinion gear will provide maximum transfer of speed and power to the motor. I am a fan of precision manufactured, quality pinion gears that when properly meshed with a new or good spur are totally silent! These gears from Yeah Racing certainly fill the bill. By Chris Kovachevich, RC Driver Issue 108, December 2012     Features: For: 1:10 EP, fit on 540 Motor Material: 7075 Aluminum Color: Titanium   Specifications: Pitch: 48 Teeth: 15   Includes: 48 Pitch Pinion 15 Teeth (1 Pc) Set Screw (1 pc)

49,-

59,-

KJØP
-17%
Hovedbilde M-DRIVE Hex/Nut Driver Tool - 8mm Hovedbilde M-DRIVE Hex/Nut Driver Tool - 8mm
M-DRIVE Hex/Nut Driver Tool - 8mm
M-DRIVE Hex/Nut Driver Tool - 8mm High quality nutdriver wrench tool with black anodized aluminium handles and tough drivers made of HSS steel. Specs: Handle: Black anodized aluminium Laser Engraving: M-DRIVE logo & size/type Handle Diameter: 18.7mm Handle Length: 100mm Total Length: 180mm Nut Driver Size: 8mm Tip/Bits Material: High quality HSS Suitable for: Nut Driver 8mm: For M5 nuts (and glow plugs)

79,-

KJØP
Hovedbilde M-DRIVE Hex/Allen Wrench Spare Tip - 2.5mm Ball Hex Hovedbilde M-DRIVE Hex/Allen Wrench Spare Tip - 2.5mm Ball Hex
M-DRIVE Hex/Allen Wrench Spare Tip - 2.5mm Ball Hex
M-DRIVE Hex/Allen Wrench Spare Tip - 2.5mm Ball Hex High quality hex/allen wrench spare HSS steel ball tip. Specs: Length: 100mm Tip/Bits Hex Size: 2.5mm (ball) Tip/Bits Diameter: 3mm Tip/Bits Material: High quality HSS Suitable for: M3 hex screws with allen head (cylindrical) M4 hex screws with countersunk head M4 hex screws with button head Note that a ball head hex/allen tool tip always wear faster that a straight hex. They are also more easy to brake when dropping them on the floor or using too much force while tightening/losening a screw.

39,-

KJØP
Hovedbilde M-DRIVE Hex/Allen Wrench Spare Tip - 2mm Ball Hex Hovedbilde M-DRIVE Hex/Allen Wrench Spare Tip - 2mm Ball Hex
M-DRIVE Hex/Allen Wrench Spare Tip - 2mm Ball Hex
M-DRIVE Hex/Allen Wrench Spare Tip - 2mm Ball Hex High quality hex/allen wrench spare HSS steel ball tip. Specs: Length: 100mm Tip/Bits Hex Size: 2mm (ball) Tip/Bits Diameter: 3mm Tip/Bits Material: High quality HSS Suitable for: M3 hex screws with countersunk head M3 hex screws with button head Note that a ball head hex/allen tool tip always wear faster that a straight hex. They are also more easy to brake when dropping them on the floor or using too much force while tightening/losening a screw.

39,-

KJØP
Hovedbilde M-DRIVE Hex/Allen Wrench Tool - 2mm Straight Hex Hovedbilde M-DRIVE Hex/Allen Wrench Tool - 2mm Straight Hex
M-DRIVE Hex/Allen Wrench Tool - 2mm Straight Hex
M-DRIVE Hex/Allen Wrench Tool - 2mm Straight Hex High quality hex/allen wrench tool with black anodized aluminium handle and tough HSS steel tip. Specs: Handle: Black anodized aluminium Laser Engraving: M-DRIVE logo & size/type Handle Diameter: 18.7mm Handle Length: 100mm Total Length: 180mm Tip/Bits Hex Size: 2mm Tip/Bits Diameter: 3mm Tip/Bits Material: High quality HSS Suitable for: M3 hex screws with countersunk head or button head

79,-

89,-

KJØP
-11%
Hovedbilde Traxxas 5347 Rod Ends w/Hollow Balls Large Revo (12)
Traxxas 5347 Rod Ends w/Hollow Balls Large Revo (12)
Denne finnes også i RPM her.   This is the Large Rod End Set for the Traxxas Revo. FEATURES: Plastic construction           Black in color           Metal Pivot Balls INCLUDES: 12 Rod Ends           12 Pivot Balls REQUIRES: Assembly to vehicle SPECS:    Length:              22mm (.88")           Width at ball joint: 10mm (.39")

119,-

KJØP
Hovedbilde BSD 221-014 Front Transverse Drive Shaft w/Axle
BSD 221-014 Front Transverse Drive Shaft w/Axle
MERKE BSD MODELL 221T Giant Racer Buggy (Børste), 222R Giant Racer Truggy, 222T Giant Racer Truggy (Børste)

269,-

KJØP
Hovedbilde Traxxas 1548 Set Screw 3x4mm (8)/4x4mm (4)
Traxxas 1548 Set Screw 3x4mm (8)/4x4mm (4)
These are the Traxxas 3x4mm and 4x4mm Set Screws. FEATURES: Constructed of steel           Also known as grub screws INCLUDES: Eight 3x4mm set screws in black.           Four 4x4mm set screws finished in natural finish. REQUIRES: 2mm hex wrench for 4x4mm screws           1.5mm hex wrench for 3x4mm screws COMMENTS: For use in Traxxas kits or any application requiring these size set             screws.

29,-

KJØP
Hovedbilde Tamiya 51425 M-05RA F PARTS UPRIGHT
Tamiya 51425 M-05RA F PARTS UPRIGHT
This is the F Parts for M-05Ra chassis. F Parts x 1pc.

99,-

KJØP

SamiRC Norge AS

© 2026 SamiRC Norge AS - Powered by Mystore.no

Om oss

  • SamiRC Norge AS
  • Nils Lauritssøns vei 34
  • 0870 OSLO
  • Org. nr. MVA 928 644 979 Foretaksregisteret
  • Tlf: 46760019
  • post@samirc.no

Kundeservice

Nyhetsbrev

  • klarna-dark.png
  • vipps-orange.png
  • mastercard-full.png
  • visa.png
  • paypal.png