Stampede VXL

Traxxas 2754 Stub Axles Pins (4)

Art.nr: TRX 2754

Copied

These pins slide through the axle and hold the wheel to the axle. INCLUDES: 4- stub axle pins

15,-

KJØP

Traxxas 2587 Cap Head Machine Screw 3x10mm Revo (6)

Art.nr: TRX 2587

Copied

This is a package of six 3x10mm Traxxas Cap Head Screws. FEATURES: Steel construction, Black in color Used on the Traxxas Revo monster truck, can also be used in any application where a 3x10mm cap head screw is required INCLUDES: Six 3x15mm Traxxas Cap Head Screws REQUIRES: 2.5mm hex head wrench SPECS: Length: 15mm Diameter: 3mm

35,-

KJØP

Traxxas 3355R VXL-3s Waterproof Brushless ESC

Art.nr: TRX 3355R

Copied

This is the Traxxas VXL-3s Waterproof Brushless Electronic Speed Control. FEATURES Auto detects brushed, brushless or sensored brushless motor types Compatible with 4-cell NiCd or NiMH batteries up to 3S LiPo packs (11.1V) EZ-Set(R) one-touch push-button set-up Three drive profiles Sport, Race and Training mode Training mode limits full throttle to 50% for beginning drivers Locked rotor protection if vehicle is stuck or motor is bound Battery over-voltage protection triggers failsafe if maximum input voltage is exceeded Sensor phase detection protects against improperly wiring aftermarket sensored motors Sensored motor backup protection switches to sensorless operation if motor sensor fails Auxiliary fan output (fan not included) INCLUDES Traxxas VXL-3s Electronic Speed Control with 12 gauge motor and battery cables, three preinstalled 3.5mm female bullet motor connectors, Traxxas High-Current male battery connector, universal receiver connector and instruction manual REQUIREMENTS Installing in vehicle and connecting to battery, receiver and motor SPECIFICATIONS Input Voltage 4.8 - 11.1V (4-9 NiMH, 2S-3S LiPo) Motor Compatibility: Sensorless Brushless Motor Limit: None Battery Connector: Trasxxas High-Current Motor Connectors: TRX 3.5 Bullet Connectors Motor and Battery Wires: 12 gauge Maxx ccable Continuous Current: 200A Peak Current: 320A forward and reverse BEC Current: 6.0V DC Transistor Type: MOSFET On-Resistance: 0.00075 ohms PWM Frequency: 12,000Hz Thermal Protection: Two-Stage Thermal Shutdown Weight: 3.88 oz (110g) Length: 2.29" (58.17mm) Width: 1.54" (39mm) Height: 1.2" (30.48mm) including heatsink

1.445,-

1.495,-

KJØP

-3%

Traxxas 3642X Shoulder Screws Ultra Shocks (6)

Art.nr: TRX 3642X

Copied

These are the Shoulder Screws for the Traxxas T-Maxx 3.3. FEATURES: Black steel construction INCLUDES: Six steel shoulder screws SPECS: Length: 12mm Diameter: 3mm

39,-

Ikke på lager

Traxxas 3644 Turnbuckles Camber Link 39mm

Art.nr: TRX 3644

Copied

These are the 39mm Turnbuckle Camber Links for the Traxxas Stampede and Rustler VXL. FEATURES: Metal and Nylon Construction Silver and Black in Color Assembled w/Rod Ends INCLUDES: Two front 39mm (69mm center to center) turnbuckles and instruction sheet REQUIRES: Installation on the vehicle

79,-

KJØP

Traxxas 3646 Flat Head Machine Hex Drive Screws 3x15mm ...

Art.nr: TRX 3646

Copied

These are the Traxxas Flat-Head 3 x 15mm Machine Screws. FEATURES: Metal construction Black in color INCLUDES: Six 3 x 15mm Flathead Hex Machine Screws REQUIRES: Installation on the vehicle

35,-

KJØP

Traxxas 3647 Nuts 4mm Flanged Nylon Locking Steel (8)

Art.nr: TRX 3647

Copied

This is the Traxxas Flanged Nylon Locking Nuts. FEATURES: Steel serrated construction INCLUDES: Eiqht 4mm flanged nylon locking nuts SPECS: Outside diameter: 7mm

39,-

Ikke på lager

Traxxas 3760A Ultra Shocks Gray Long (2)

Art.nr: TRX 3760A

Copied

Denne passer til: -Bandit XL5/VXL foran. -Rustler XL5/VXL foran. -og til flere Traxxas biler. Sjekk manualen til din bil. This is a pair of the Long Ultra Shocks from Traxxas for the Bandit. FEATURES: Gray composite bodies Preload spacers and two red springs INCLUDES: Two ultra long grey shocks with bottle of silicone oil and assembly diagram REQUIRES: Assembly COMMENTS: Two pairs are required if replacing all shocks.

259,-

289,-

KJØP

-10%

Traxxas 2734 Cable Ties Small (10)

Art.nr: TRX 2734

Copied

This is a package of cable ties. FEATURES Easily holds wires in place & other small items INCLUDES 10 Black cable ties SPECIFICATIONS 3 1/16" long (76mm) 3/32" wide (2.5mm)

25,-

KJØP

Traxxas 3932 Flat Head Machine Hex Drive Screws 3x6mm ...

Art.nr: TRX 3932

Copied

These are the 3x6mm Flathead Machine Screws used on the Traxxas T-Maxx 3.3 RTR. FEATURES: Constructed of steel, black in color INCLUDES: Six 3x6mm Flathead Machine Screws REQUIRES: 2.5mm hex wrench. SPECS: Length: 6mm Diameter: 3mm COMMENTS: Can be used in any application where a screw of this size is needed.

35,-

KJØP

Traxxas 2735 Front Bumper

Art.nr: TRX 2735

Copied

This is the replacement front bumper for the TRX-1 and TRX-3. It is molded of white plastic. It is 2 3/8" long. INCLUDES: 1- front bumper

39,-

KJØP

Traxxas 3934 Body Clips (12)

Art.nr: TRX 3934

Copied

Heavy-duty body clips hold tightly for the intense, high-flying action of our toughest 1/10 scale vehicles. Sold as a pack of 12. FEATURES: Steel construction Natural polished color INCLUDES: Twelve Body Clips SPECS: Length: 26mm

39,-

KJØP

Traxxas 3937 Button Head Machine Screw 4x12mm Revo (6)

Art.nr: TRX 3937

Copied

This is a Traxxas 4X12mm Button Head Screw Set. FEATURES: Steel construction Black in color Low-profile, button-head design Hex drive (allen type) INCLUDES: Six Screws REQUIRES: Assembly to vehicle SPECS: Overall Length: 12mm (.63") Threaded Length: 11mm (.45") Thread Size: M4x.7mm coarse Hex Wrench Size 2.5mm COMMENTS: Used on the Revo to mount the transmission skid plate.

35,-

Ikke på lager

Traxxas 3965 Cap Head Machine Screw 2.5x8mm Revo (6)

Art.nr: TRX 3965

Copied

This is a 6 pack of Traxxas 2.5X8mm Cap Head Screws. FEATURES: Steel construction Black in color Cap head design INCLUDES: (6) 2.5X8mm cap head screws SPECS: Length: 5/16" (8mm) Diameter: 3/32" (2.5mm

35,-

KJØP

Traxxas 2753X Stub Axles Rear (2)

Art.nr: TRX 2753X

Copied

These are the Rear Stub Axles for the Traxxas Bandit, Stampede 2WD and Rustler. FEATURES: Metal construction, black and silver in color INCLUDES: Two rear stub axles and pins SPECS: Length: 1.65" (42mm) Diameter: .51" (13mm) at largest point

59,-

79,-

KJØP

-25%

Traxxas 4859 Flathead screw M3x10

Art.nr: TRX 4859

Copied

Screws, 3x10mm flat-head machine (hex drive) (4)

25,-

KJØP

Traxxas 5347 Rod Ends w/Hollow Balls Large Revo (12)

Art.nr: TRX 5347

Copied

Denne finnes også i RPM her. This is the Large Rod End Set for the Traxxas Revo. FEATURES: Plastic construction Black in color Metal Pivot Balls INCLUDES: 12 Rod Ends 12 Pivot Balls REQUIRES: Assembly to vehicle SPECS: Length: 22mm (.88") Width at ball joint: 10mm (.39")

119,-

KJØP

Traxxas 5525 Rod Ends/Hollow Balls

Art.nr: TRX 5525

Copied

These are the Rod Ends and Balls for the Traxxas Slash 4x4 and other Traxxas cars. FEATURES: Black nylon construction. Steel hollow balls. INCLUDES: Twelve rod end/balls REQUIRES: Installing on Jato SPECS: Length: 1-1/8" (28mm) Width: 3/8" (9mm)

119,-

129,-

KJØP

-8%

Traxxas 3195 Top Steel Drive Gear 22T Nitro Hawk

Art.nr: TRX 3195

Copied

This is the 22 tooth, hardened steel top drive gear. Fits: Traxxas Rustler VXL/XL-5 Stampede VXL/XL-5 Bandit VXL/XL-5 1/10 Slash 2WD

39,-

Ikke på lager

Traxxas 3628 Reciever Box Stampede/Rustler/Bandit

Art.nr: TRX 3628

Copied

This is the Receiver Box for use on the Traxxas Stampede, Rustler, and Bandit Vehicles. FEATURES: Nylon construction Black in color INCLUDES: One Receiver Box One Rubber Seal Foam Padding Two 2.5x8mm Cap Head Screws Two 3x10mm Cap Head Screws Two 2.5x10mm Cap Head Screws One Tube of Grease Instruction sheet REQUIRES: Installation on the vehicle SPECS: Length: 78mm (3.07") Width: 35mm (1.4") Height: 33mm (1.3")

145,-

Ikke på lager

Traxxas 3629 Seal Kit Rx Box Stampede/Rustler/Bandit

Art.nr: TRX 3629

Copied

This is the Receiver Box Seal Kit for the Traxxas Stampede, Rustler, and Bandit. FEATURES Properly seals receiver box to minimize dirt and moisture exposure INCLUDES Silicone grease One Gasket Two Foam Strips Instructions REQUIREMENTS Application to receiver box

49,-

KJØP

Traxxas 3631 Suspension Arms Front (2)

Art.nr: TRX 3631

Copied

This is the Traxxas replacement #3631 Front Suspension Arms for for the Stampede and Rustler. FEATURES: Made from black molded nylon For the Traxxas Stampede and Rustler. SPECS: Length: 3 1/4" Thickness: 3/8" Width at end near chassis: 1 1/2" Width at end near wheels: 7/8" INCLUDES: (2) Front suspension arms for the Traxxas Stampede.

99,-

KJØP

Traxxas 3632 Caster Blocks Left/Right

Art.nr: TRX 3632

Copied

These are Castor Blocks for the Traxxas Rustler and Stampede. FEATURES: Black Plastic Construction INCLUDES: Two Blocks REQUIRES: Traxxas Rustler or Stampede COMMENTS: None

49,-

KJØP

Traxxas 3637 Front Axles (2)

Art.nr: TRX 3637

Copied

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede. These are located in the front steering blocks. FEATURES: Steel construction Natural color INCLUDES: Two front axles REQUIRES: Nothing. These are direct replacement parts. SPECS: Length: 32mm (1.26") Diameter: 5mm COMMENTS: These will not work for the nitro versions. For that axle, use TRX 2536,

39,-

KJØP

"Bulk" Traxxas 6533X Micro TQi 5-channel Telemetry TSM ...

{ this.copied = false; }, 2000); } }" x-show="model || ean">

Art.nr: "BULK" TRX 6533X

Copied

*** This is a Brand new item taken from a kit (chopped part), therefore will not have a Traxxas packaging *** Traxxas 6533X - Receiver, micro, TQi 2.4GHz with telemetry & TSM® (5-channel) This is the Traxxas TQi Stability Management Receiver. FEATURES Compatible with Traxxas TQi transmitters equipped with a Multi- Function knob Turned on or off and adjusted via the Multi-Function Knob, or by adjusting the slider in the Traxxas link app Provides greater control on loose dirt, concrete, ice and snow Stabilizes vehicles over rough surfaces as the gyro effect of the spinning front tires continue to "steer" when vehicle is in the air Allows faster cornering speeds Does not restrict throttle Improves braking performance and prevents spinouts Fully conpatible with Traxxas Link Works invisibly in the background to allow driver to maintain connected feel with the vehicle INCLUDES Traxxas TQi Stability Management Receiver REQUIREMENTS Traxxas TQi transmitters with Multi-Function knob Connecting to Traxxas Link App (iOS or Android version) required to update receiver firmware with TSM profile for specific model Traxxas Link Wireless Module may also be required depending on TQi radio to connect to a smartphone via bluetooth

549,-

699,-

Ikke på lager

-21%

Populært i denne kategorien

SamiRC Norge AS

Om oss

Kundeservice

Totalt:

Søkeresultater

Stampede VXL

Populært i denne kategorien

Totalt:

Tamiya El-biler

Kyosho-Biler

Mini-Z

Carson

Tamiya Lastebiler

Reservedeler til Lastebil

Reservedeler til Hengere

E-flite RC

Traxxas & Latrax Reservedeler

Sendere

Spektrum sendere

Spektrum mottakere

Mottakere

Spektrum Mottakere

Telemetri

Hitec

Servoer

Servoer etter størrelse

Reservedeler

Option-parts

Option Parts Biler

Tamiya Biler

Servo anbefalinger til biler

Maverick biler

Traxxas biler

Kyosho biler

Mini-Z biler

Tamiya biler

HPI Biler

Redcat

Servo anbefalinger til båt

Crawler motor & regulator

Børsteløs/Brushless

Børsteløs combo

Børsteløs motor

Børsteløs Bil motor

Børsteløs regulator

Reservedeler til motorer

Flymotorer

OS motorer

Lipo

Lipo 3 celler 11.1 volt

3 celler sortert etter plugg

Lipo 4 celler 14,8 volt

4 celler sortert etter plugg

NiMH

Mottakerbatteri

Batteri etter produsent

LiFe

Traxxas Biler

Traxxas 68086-4 Slash 4x4 VXL

Traxxas Båter

Alle fly

Redcat Biler

Maverick biler

Kyosho biler

Kyosho Mini-Z

HPI biler

Reservedeler etter Produsent

Traxxas El-Biler

Arrma

Traxxas Nitro-Biler

Tamiya El-Biler

TT-01

Axial El-Biler

SCX10 Honcho

Kyosho-El-biler

Mini-Z deler

Kyosho Fazer D2 FZD2

Utgåtte Kyosho biler

Kyosho Nitro Biler

RC4WD-Biler

Vaterra-Biler

WL-Toys

HAIBOXING Biler

Helion-biler

BSD Biler