Hopp til innhold
-17%

Traxxas 3147X Fuel line (610mm or 2ft)

Art.nr: TRX 3147X

49,-

59,-

- 17%
Traxxas

Traxxas

** Ikke på lager

Produktet er midlertidig utsolgt. Dersom du ønsker å motta en epost når vi får det inn på lager, kan du legge igjen epostadressen din i skjemaet under.

Informasjon

 

Fuel line (610mm or 2ft)

Produsent

Dette er den beste merket for RC-BIL i hele Norge, nei vi kan vel si hele verden uten å trenge å være redd for at vi sier noe galt!

Relaterte produkter

 

Art.nr: 38215
Copied
Sullivan S215 ProFlex Fuel Line 4 mm id, 60cm S215 - ProFlex 5/32" ID (4 mm) Universal Tubing 60 cmLarge Size Tubing has a 5/32" ID (4 mm) which is designed to fit 3/16" (4.8 mm) brass tubing as well as large size fuel fittings. In order to use the large size ProFLex in a tank you must replace the brass tubes and klunk to 3/16". We designed our new ProFlex fuel line with a US chemist and rubber compounder to develop a proprietary formula of FKM (Fluoroelastomer) that is chemically resistant to gasoline and ethanol which is what causes Tygon tubing to harden and deteriorate. With the help of an experienced US extruder, ProFlex has a thinner wall than commonly found on the Tygon that is used today. The thinner wall allows for more flexibility, lighter weight and easier attachment to tubing and fittings used in the RC industry.

165,-

KJØP

Kunder kjøpte også

OptiFuel 101909K - After-Run Oil 50ml This is a bottle of after-run oil suitable for all internal combustion engines (mostly run on methanol/nitro based fuels). The oil also works good as an engine assemble oil. Directions: After a day of running the engine - empty the fuel tank of most of it's fuel. Leave enough fuel for the engine to be able to run a couble of minutes at idle speed. Start the engine, let it idel and reach working temp and let it idle until the remaning fuel in the tank is empty, as in the engine stops by istelf. Try starting the engine again until you are sure that there is no more fuel in the tank/fuel lines or the engine itself. Remove the glowplug and remove any airfilter system. Add a few drops of OptiFuel after-run oil through the glowplug hole and the carburettor opening. Spin the engine carefully/slowly a few times to spead the oil inside the engine and bearings. Inspect the glowplug and check it's condition - replace if needed. Re-install the glowplug. If your engine has an airfilter system (car engines) - clean it and/or replace it. If it's a "wet oil" filter - re-apply the foam with a special airfilter oil. Re-install the airfilter.

89,-

99,-

KJØP
-10%
6,0V 2000mAh - Bronto RX Pack - Ni-Mh Lengde 71,5mm Bredde 52mm Høyde 14,5mm Plugg JR servoplugg Ledning 10cm 22AWG Vekt 144gram

185,-

KJØP
Glow Plug No.8

99,-

KJØP
For 0.18 to 0.28ci (3 to 4.7cc) 20% to 30% Nitro HPI Power Plugs for Nitro car and truck engines! HPI Power Plugs coils use a unique blend of Platinum and Rhodium metals to produce a high quality range glow plugs that is the perfect match for HPI's range of Nitro Star engines. For use with a 1.5v Glow Igniter. Recommended Power Plugs for HPI engines: #160409 Standard Glow Plug Hot B4 #160410 Standard Glow Plug Medium B5 #160411 Standard Glow Plug Cold B6 (Std. Fit HPI Engines)

159,-

KJØP
D-MAX™ Charging Harness for Radio Batteries with Futaba Connector This is a charge lead for charging TX & RX radio batteries with a Futaba connector. Specs: Length: 50cm Wires: 20AWG Charger Connectors: 4mm male bullets Battery Connector: Futaba RX

69,-

KJØP
D-MAX™ Charging Harness for 1.2V Pocket-Booster This is a charge lead for charging a one cell NiCd/NiMH pocket booster glow starter batteries. Specs: Length: 30cm Wires: 20AWG Charger Connectors: 4mm male bullets Battery Connector: Pocket Booster / Glowplug

65,-

KJØP
Llightweight suspension arms deliver quick suspension response and reduce the overall weight of the truck. The improved design of the wishbones ensures they keep their strength and durability.

259,-

KJØP
HPI 86058 - DOGBONE 9x123mm (BLACK/2pcs) Savage THIS PART FITS THE FOLLOWING KITS / PARTS: Savage X 4.6 RTR 2.4GHz RTR Savage 4.6 2.4GHz Savage X 4.6 SAVAGE 21TRUCK WITH NITRO GT-1 RTR Savage 25 RTR Savage 25 Limited Edition (3) Savage ATV Kawasaki KFX700 Savage X 4.1 RTR Savage X 4.6 RTR Savage X 4.6 Reverse RTR SAVAGE 3.5 TRUCK WITH NITRO GT-1.

225,-

KJØP
Screws, 3x10mm washerhead machine (6)

19,-

KJØP
Maskinert metall filter, som er delbart. Det har ett finmasket netting filter av metall tråder, og er beregnet for glow og diesel fuel.

209,-

219,-

KJØP
-5%
RPM True-Track Rear End Kit for Revo 3.3 & Revo (old) - Blue Replaces stock Traxxas #5331, #5332 & #5334 Quick Notes: Fits both the Revo 3.3 and E-Revo (does not fit the E-Revo 2.0) Replaces stock Traxxas #5331, #5332 & #5334 32 grams lighter than stock components! Perfect rear toe angles Includes massive oversized bearings Matching Front Left & Front Right A-arms are available Matching Front Axle Carriers are available The RPM True-Track Rear A-arm Conversion Kit for the Revo eliminates some of the biggest headaches associated with toe link rear ends. Rear toe angles are nearly impossible to set accurately and there isn’t a gauge currently made that can accurately identify whether each individual wheel’s toe angle is set correctly in relation to the chassis. The RPM True-Track rear end kit completely eliminates the rear toe links, locking in the rear toe angle at a solid 1.5 degrees per side for a total rear toe-in angle of 3 degrees. By getting rid of the rear toe links, we’ve completely eliminated all rear bump steer! That means the rear toe angle remains consistent throughout the entire range of suspension travel, providing superior rear end tracking regardless of the terrain. Identical to our T/E-Maxx True-Track Kit, the Revo True-Track Kit retains the stock upper pivot ball in the new, ultra beefy RPM axle carrier to allow precise camber adjustments while the lower pivot ball has been eliminated in favor of a rock-solid 4mm diameter hinge pin that locks in the rear toe angles for race winning consistency (hinge pin replacement part #80970). All aspects of the RPM True-Track Conversion Kit have been beefed up for rugged durability and slop free movement throughout its range of travel. Additionally, we’ve incorporated our oversized bearings into the new RPM axle carrier design, providing an additional 2mm more bearing contact with the axle while doubling the bearing load rating & tripling the fatigue rating over the stock bearings. So does all this come at a cost of added weight? The RPM Revo True-Track Rear A-arm Conversion Kit actually weighs LESS than the stock components it replaces! How much less? 16 grams PER SIDE! That’s a total weight loss of 32 grams or 1-1/8 ounces! That means you get perfect rear toe angles, added A-arm strength, bearings that are more durable & longer lasting, an unbeatable breakage warranty and a reduction in weight! What more can anyone ask for? What’s Included: Our Revo True-Track Rear End Kit consists of two upper rear A-arms, two lower rear A-arms, two beefy rear axle carriers, two outer 6x15mm sealed bearings, two inner 12x21mm sealed bearings, two aluminum pivot ball setscrews, two delrin pivot ball bushing cups, two M3x16mm shock mount screws, two 4mm diameter tool steel hinge pins & enough e-clips to get the job done (4 minimum). RPM Recommendations: The RPM True-Track System is designed to match RPM A-arms (Part #80212 & #80215 – Right Side & #70372 & #70375 – Left Side) & Axle Carriers (#80582 & #80585 – 1 package needed) currently available for the Revo. With the True-Track system mounted at the rear and a set of RPM replacement A-arms & Axle Carriers up front, you are assured the best & most indestructible A-arm / Axle Carrier combination possible! To prolong the life of your bearings, RPM recommends the use of our #81170 Bearing Blaster. For accurate camber adjustments, please consider the use of our #70950 Monster Camber Gauge. Tech Notes: These rear end kits work on all earlier versions of the Traxxas Revo (does not fit the Revo 2.0). One kit will complete the entire rear end. These kits will not work in conjunction with Traxxas (#5356) 120-LT Long Travel Rockers.

599,-

KJØP
Traxxas 5451X Driveshaft assembly (1), left or right (fully assembled, ready to install)/ 4x15mm screw pin (1)

149,-

169,-

KJØP
-12%
   These are the Center Half Shafts for the Traxxas Revo 3.3. FEATURES: Constructed of hardened plastic           For front and rear driveshafts INCLUDES: Two external splined shafts           Two internal splined shafts REQUIRES: Installing between yokes on each drive shaft assembly SPECS:    Length: 1.9" (48.2mm)

55,-

KJØP
  RPM Front Right Arms for the Summit, Revo 3.3 & E-Revo (old) - Blue Replaces stock Traxxas #5331 Quick Notes: Fits Traxxas Summit, Revo & E-Revo Replaces stock Traxxas #5331 Matching Front Left A-arms are also available Matching True-Track Rear End Conversion Kits are available (for the Revo & E-Revo) RPM Revo A-Arms are the only alternative to bulletproof performance that rivals any competition! Features: Nearly identical in weight to stock A-Arms. Redesigned for incredible durability under the toughest of conditions. More wear resistant than any other material available. Excess A-arm end-play has been eliminated for more accurate caster and toe angle settings. Angled leading and trailing edges eliminate dirt build-up. No low-hanging cross-braces or shock mounting areas providing better ground clearance. Massive shock rod mounting areas for improved rigidity. Available in black & blue. Less than half the price of aluminum A-arms. Molded from our bulletproof blend of nylons and backed by our world renowned breakage warranty. Sold in sets of one upper and one lower A-arm.

209,-

KJØP
Convert your Traxxas Revo to forward only with this Forward Only  Conversion Kit from Traxxas.     FEATURES All parts required to convert the Revo to forward only   INCLUDES One forward only shaft (aluminum construction)  Two forward only gears (white nylon construction)  Two 3x3.75mm screw pins  One sensor cover (one black plastic plastic construction)  One black plastic cover (covers the spot that the optidrive was)  One blue rubber plug   REQUIREMENTS Assembly following the included instructions and exploded view

129,-

KJØP
Trykk her for høyre side.   RPM Front Left Blue A-arms for the Traxxas Summit, Revo & E-Revo (1.0) Quick Notes: Fits the Traxxas Summit, Revo & E-Revo (1.0) Replaces stock Traxxas #5332 Matching Front Right A-arms also available Matching True-Track Rear End Conversion Kit available (for the Revo & E-Revo 1.0) In response to repeated customer demands, we have a set of front left A-arms now available for the Traxxas Summit. Our front right A-arms for the Traxxas Revo (reference RPM #80212 & #80215) are already compatible with the Summit but due to the extended T-Lock differential on the left side, our Revo front left A-arms would not fit. That is no longer an issue with these A-arms. With a revamped cross-brace to clear the T-Lock differential, our Summit front left A-arms will allow full suspension travel and significantly improve overall suspension durability. RPM front A-arms for the Traxxas Summit are molded from our indestructible blend of engineering grade nylons for unmatched performance and durability. Every RPM molded part in manufactured in the USA and carries with it a limited lifetime warranty against breakage. If you’re tired of replacing broken stock parts over and over, give RPM a try. INCLUDES Front Upper and Lower Left A-Arms  Instruction Sheet

209,-

KJØP
This is the Brake Yoke w/Pins for the Traxxas Revo.  It is use on the Center/Front Driveshaft Assembly.     FEATURES Plastic Brake Yoke  Steel Brake Pins(each knurled on one end)  Steel Screw Pins   INCLUDES One Brake Yoke  Two Brake Pins  One Screw Pin   REQUIREMENTS Assembly to the vehicle   SPECIFICATIONS  Brake Yoke Outer Diameter: 18.5mm (.73")  Brake Yoke Center Key Size: 4mm x 6mm (.17" x .24")  Brake Yoke Length: 24mm (.95")  Screw Pin Size: 4mm x 15mm (Threaded length-5mm)  Brake Pin Size: 3mm x 20mm (.12" x .8") COMMENTS Brake Yoke Center is "keyed" to have a positive fit to the shaft.

49,-

KJØP
Traxxas 70WT/900cSt Premium Shock Oil 60ml New from Traxxas is a complete line of premium silicone shock oil. Available in seven steps of viscosity, this 100% pure silicone oil allows precise vehicle suspension tuning for maximum performance, no matter where you drive. The precision-pour, the twist-nozzle cap makes it quick and easy to fill shock bodies, without all the mess. cSt viscosity specification ensures consistent performance with every bottle. Features: Seven precise viscosities ranging from 200cSt to 1000cSt (20wt to 80wt) 100% silicone oil for maximum consistency Precision-pour, twist-nozzle cap Specs: Viscosity: 70WT (900cSt) Bottle size: 60ml

99,-

109,-

KJØP
-9%
This is a pair of the Steering Blocks for the Traxxas Nitro and Electric Powered 4-Tec Touring Cars. These Blocks support the Wheel Hubs and connect to the Front Suspension Arms and Steering Tie Rods. FEATURES Constructed of high impact plastic Replaces worn or damaged Steering Blocks INCLUDES Two Steering Blocks for the Traxxas Nitro and Electric Powered 4-Tec Touring Cars with four metal inserts. All are Key #4336 REQUIREMENTS Inserting two 5mm x 10mm ball bearings, fastening to Front Suspension Arms TRX 4831, and Tie Rods TRX 4841 COMMENTS For the optional aluminum version, order TRX 4336X

49,-

KJØP
  0-OFFSET - 4WD FRONT & REAR Fits: Traxxas E-MAXX Brushless Front & Rear Traxxas REVO 3.3 Front & Rear Traxxas E-REVO Brushless Front & Rear Arrma Kraton Front & Rear Arrma Talion Front & Rear Arrma Nero Front & Rear HPI SAVAGE X 4.6 Front & Rear HPI TROPHY Flux 4WD Front & Rear HPI SAVAGE FLUX HP Front & Rear HPI SAVAGE XL Flux Front & Rear Kyosho Psycho Kruiser 4WD Front & Rear Also fits other 1/8 Scale Monster Trucks with 17 mm hex Also fit these Traxxas Trucks if converted with 17 mm hexes - 5353X, 5353G & 5353R: Traxxas E-Maxx Front & Rear  Traxxas E-Maxx Front & Rear  Traxxas E-REVO Front & Rear  Traxxas E-REVO Front & Rear  Traxxas T-Maxx 3.3 Front & Rear  Traxxas T-Maxx 3.3 Front & Rear  Traxxas T-Maxx 3.3 Front & Rear  Specs: Wheel diameter: 3.8" Tire Diameter: 171 mm Tire Width: 109 mm Weight (each): 428 g Hex: 17 mm Offset: 0" Tire Compound: Sport Wheel finish: Black Nylon

579,-

599,-

KJØP
-3%
Disse lagerene er samme størrelse som Tamiya 1150 Yeah Racing RC PTFE Bearing (5x11x4mm) 10pcs Features: RC Ball bearings should always be your first upgrades, it reduces friction for less rolling resistance, and that means higher speed and longer the running times. RC Ball bearings hardly require maintenance and last a lot longer than stock Oilite bushings. Yeah Racing RC Ball Bearings have the lowest resistance. They are manufactured by Aircraft quality steel. Pre-lubricated to ensure its excellent performance! These high quality bearings outweigh the other low quality one: Aircraft quality material More durable Higher precision   Specifications: Yeah Racing (#YB6014BS/10) RC Telfon Bearing (5x11x4mm) Material: Metal   Includes: Bearing (10Pcs)   Tips on Cleaning & Lubricating Ball Bearings (RC Bearing Tips) Tips for Handling New Ball Bearing: Most competition RC racers will clean the grease on the new ball bearings and apply ball bearing oil on them. (i.e. Yeah Racing High Speed Bearing Oil / Lube #YA-0215). As re-oiling the ball bearing allows the RC cars to run smoother and makes the bearings more durable. Tips for Maintaining Old Ball Bearing: By removing the old bearing oil, it will reduce the friction in the bearing, thus making RC car run faster.

89,-

99,-

KJØP
-10%
Disse lagerene er samme størrelse som Tamiya 850 Yeah Racing RC PTFE Bearing (5x8x2.5mm) 10pcs Features: RC Ball bearings should always be your first upgrades, it reduces friction for less rolling resistance, and that means higher speed and longer the running times. RC Ball bearings hardly require maintenance and last a lot longer than stock Oilite bushings. Yeah Racing RC Ball Bearings have the lowest resistance. They are manufactured by Aircraft quality steel. Pre-lubricated to ensure its excellent performance! These high quality bearings outweigh the other low quality one: Aircraft quality material More durable Higher precision   Specifications: Yeah Racing (#YB6011BS/10) RC Telfon Bearing (5x8x2.5mm) Material: Metal   Includes: Bearing (10Pcs)   Tips on Cleaning & Lubricating Ball Bearings (RC Bearing Tips) Tips for Handling New Ball Bearing: Most competition RC racers will clean the grease on the new ball bearings and apply ball bearing oil on them. (i.e. Yeah Racing High Speed Bearing Oil / Lube #YA-0215). As re-oiling the ball bearing allows the RC cars to run smoother and makes the bearings more durable. Tips for Maintaining Old Ball Bearing: By removing the old bearing oil, it will reduce the friction in the bearing, thus making RC car run faster.

79,-

89,-

KJØP
-11%
Programmerbar 2,4 GHz-rattradio for bil eller båt. En veldig bra bil og båt radio til en gunstig pris. GT-3B er en programmerbar rattradio med tre kanaler. Radioen sender på 2,4 GHz-båndet, noe som gir en mye sikrere signaloverføring og dette eliminerer forstyrrelser. Via LCD-displayet kan du raskt stille inn radioen slik du ønsker for akkurat ditt kjøretøy og lage de avanserte innstillinger for ABS-brems, dual rate, reversering, servokontroll m.m. Radioen har 10 modellminner. Mål 315x159x99 mm. Vekt 328 g. Leveres med mottaker og bindingskontakt. Manual på Engelsk medfølger. Key Features – Model Memory – Servos NOR/REV – Steering Trim – Throttle Trim – Dual Rate – End Point – ABS Settings – EXP Settings – Trainer Port (for VRC) – CE & FCC certified Specification – Channels : 3 Channels – Model type : car/boat – RF range : 2.40-2.48GHz – Bandwidth : 500Hz – Band : 160 – RF power : less than 20DB – 2.4G system : AFHDS – Code type : GFSK – Sensitivity : 1024 – Low voltage warning : yes(less than 9V) – DSC por t: yes(3.5mm:output:PPM) – ST range : 90 – TH range : 45(F:30;B:15) – Charger port : yes – Power : 12V DC(1.5AA*8) – Weight : 328g – ANT length : 26mm – Size : 159 x 99 x 315mm – Color : black – Certificate : CE,FCC Includes : – 1 x 2.4Ghz transmitter – 1 x 2.4Ghz Receiver – 1 x Bind Plug

699,-

849,-

KJØP
-18%
This is the Long Temperature and Voltage Sensor from Traxxas. FEATURES: Functions with the Traxxas Link system to display battery voltage and             temperature INCLUDES: Long Temperature and Voltage Sensor with Mounting Screw SPECS:    Length: 14" (356mm)

139,-

159,-

KJØP
-13%
This is the Steering Linkage for the Traxxas Revo. FEATURES: Connects between servo horns and steering arms INCLUDES: Two 3x30mm steel turnbuckles, four short rod ends and four hollow             balls REQUIRES: Installing on steering assembly according to instructions in manual

45,-

KJØP
  • klarna-dark.png
  • vipps-orange.png
  • mastercard-full.png
  • visa.png
  • paypal.png