Hopp til innhold

Traxxas 5522X Aluminum Chassis Jato

Art.nr: TRX 5522X

559,-

Traxxas

Traxxas

På lager: 1

Produktet er midlertidig utsolgt. Dersom du ønsker å motta en epost når vi får det inn på lager, kan du legge igjen epostadressen din i skjemaet under.

Informasjon

This is the optional Lightweight T6 Aluminum Chassis for the Traxxas
                                 Jato.

FEATURES: High-grade 7075-T6 Aluminum construction, in a titanium anodized
           finish make for a chassis 40% stronger than the stock chassis
          Extra material is milled out of the top of the chassis to make it
           10% lighter than the stock chassis
          Fully coutersunk on the bottom
          Less flex improves handling response
          Laser-etched Jato logo adds to the trick look
          Direct fit hop-up requires no modification for use

INCLUDES: One chassis
          One 1x3" adhesive foam pad

REQUIRES: Assembly onto Truck

Produsent

Dette er den beste merket for RC-BIL i hele Norge, nei vi kan vel si hele verden uten å trenge å være redd for at vi sier noe galt!

Kunder kjøpte også

  Bronto ladekabler er et must for RC-entusiasten. Ladekabelen er utstyrt med kvalitets 22AWG ledninger. Ladeledningen har en praktisk lengde på 30cm, noe som er godt egnet når du f.eks skal legge batteriet trygt i en sikker ladebag mens det lades. Ladekabel med JST til XT60-plugger. Benyttes for lading av batterier med JST, og kobles rett i ladere med XT60 tilkobling. Spesifikasjoner   Ledning 22AWG Lengde 30cm Tilkobling 1 XT60 Tilkobling 2 JST

65,-

KJØP
Louise ST-UPHILL Stadium Truck Tires on 1/2-Offset Black 2.8" Wheels Fits: Traxxas RUSTLER 4x4 Front & Rear Traxxas STAMPEDE 2WD Front Traxxas STAMPEDE VXL 2WD Front Traxxas RUSTLER 2WD Front Traxxas RUSTLER VXL 2WD Front Traxxas SKULLY 2WD Front Traxxas CRANIAC 2WD Front Traxxas STAMPEDE 4x4 Front & Rear Traxxas STAMPEDE VXL 4x4 Front & Rear Traxxas JATO 2WD Rear Traxxas Nitro STAMPEDE 2WD Rear Traxxas Nitro RUSTLER 2WD Rear Traxxas Nitro Sport SE 2WD Rear HPI SAVAGE XS Flux Front & Rear HPI Jumpshot MT 2WD Front & Rear HPI Jumpshot ST 2WD Front & Rear HPI Bullet Flux MT 4WD Front & Rear HPI Bullet Flux ST 4WD Front & Rear HPI E-Firestorm 10T 2WD Front & Rear Also fits other 1/10 Scale Trucks with 12 mm hex Specs: Wheel diameter: 2.8" Tire Diameter: Tire Width: Weight (each): Hex: 12 mm Offset: +1/2" Tire Compound: Soft Wheel finish: Black Nylon

299,-

329,-

KJØP
-9%
DynoMAX B9694 - EC5 Charging Lead for Chargers with 4mm Banana Outputs This is a charging lead for batteries with a EC5 connector. It fits chargers that are equipped with 4mm banana connectors. Specs: Battery Connector: EC5 Charger Connector: 4mm Banana Bullets Wires: 14AWG Length: 500mm

85,-

KJØP
Receiver cover (chassis top plate), Exo-Carbon finish (Jato®) Traxxas Exo-Carbon components add a glossy, high-tech carbon-fiber look to Jato. The innovative Exo-Carbon finish forms a tough skin over standard Jato composite parts resulting in the quality and strength you expect along with the appearance of high-gloss carbon fiber. Exo-Carbon resists fuel and abrasion for long-lasting good looks.

Lock Nut Flanged M4 Alu Red (4)

99,-

109,-

KJØP
-9%
Seal kit, expander box (includes o-ring, seals, and silicone grease)

49,-

KJØP
3mm (1/8) Thick Silicone Fuel Tube 1 meter lang.

49,-

KJØP
This is the Recoil Starter for the 2.5 and 3.3 Traxxas engines.     FEATURES Black plastic case   INCLUDES One Recoil Starter  Four 3mm x 12mm cap head screws   REQUIREMENTS 2mm Allen Wrench   SPECIFICATIONS  Mounting Holes center-to-center: 27mm   COMMENTS This part is for the recoil unit only  Screws have thread-locking compound pre-applied

269,-

KJØP
Type of Battery: NiMH Capacity: 1600 mAh Number of cells: 5 Voltage: 6,0 V

269,-

KJØP
DynoMAX B9668 - Futaba RX Charge Lead for Chargers with an XT60 Output This is a charging lead for batteries with a Futaba RX connector. It fits the latest SkyRC chargers that are equipped with a XT60 male output/charging connector. Specs: Battery Connector: Futaba RX Charger Connector: XT60 Wires: 20AWG Length: 500mm

65,-

KJØP
  This is the Drag Link w/Bearing               for the Traxxas Nitro Jato Stadium Truck. FEATURES: Aluminum Construction           Anodized Blue in Color INCLUDES: One Drag Link w/Pre-Installed Bearings           Four 5mm x 8mm Washers REQUIRES: Assembly onto Vehicle

215,-

KJØP
This is the Glow Plug Lead Wire for the Revo EZ Starting System.     This attaches to the glow plug prong to heat the plug during starting. FEATURES: Blue silicone insulated wire with pre-installed connectors INCLUDES: One glow plug wire lead           One Molex pin extractor tool REQUIRES: Nothing.  This is a direct replacement part.

25,-

Ikke på lager
 This is the optional Aluminum Turnbuckle set for the Traxxas Jato. FEATURES: Anodized aluminum construction, red in color           Black nylon ball ends INCLUDES: Four 58mm camber links with 31mm hollow ball ends           Two 61mm front toe links with 31mm hollow ball ends           One 5mm aluminum wrench REQUIRES: Installing on Jato

399,-

KJØP
                 These are the Front/Rear Suspension Tie Bars               for the Traxxas Nitro Jato Stadium Truck. FEATURES: Aluminum Construction           Blue in Color INCLUDES: One 4° F/R Suspension Tie Bar           One F/R Suspension Tie Bar REQUIRES: Assembly onto Vehicle

59,-

KJØP
This is the Traxxas Super Duty Long Glowplug. FEATURES: Ideal for all Traxxas engines including the 2.5, 2.5R and 3.3 engines           Suited for the varied throttle range of off-road racing           Medium heat range INCLUDES: One Traxxas Medium Heat Range Super Duty Long Glowplug with gasket REQUIRES: Plug wrench  for installing in cylinder head           Glow Fuel with 10%-20% nitro content  

119,-

139,-

Ikke på lager
-14%
Body clip (mounting clip), angled, 90-degrees (black) (10)

39,-

KJØP
This is pair of Rear Aluminum Stub Axle Carriers for the Traxxas JATO. FEATURES: Titanium anodized           6061-T6 Aluminum INCLUDES: A pair of rear axle carriers

475,-

KJØP
These are the optional Front Caster Blocks for the Traxxas Jato.              These are located on the front suspension assembly. FEATURES: Titanium-anodized aluminum INCLUDES: One Pair of Caster Blocks REQUIRES: Traxxas Jato COMMENTS: These are replacements for the stock plastic caster blocks.

349,-

KJØP
  These are the replacement Body Clips for                     the Traxxas Nitro Revo Monster Truck. FEATURES: Metal Construction           Silver in Color           Bent for Easy Removal INCLUDES: Ten Bent Silver Metal Body Clips REQUIRES: Assembly onto Vehicle

39,-

Ikke på lager
These are Optional Blue Anodized Aluminum Wheel Hex Hubs for Traxxas vehicles      such as the Stampede, Rustler, 4-Tec, and other older Traxxas kits. FEATURES: Blue aluminum construction INCLUDES: Two hex hubs           Four axle pins REQUIRES: Assembly onto axles. SPECS:    Hex Length: 12mm (.47")           Hex Thickness: 6.1mm (.24")           Axle Pin Length: 9.6mm (.38") COMMENTS: These hubs could be used with other vehicles utilizing the same             pin/hex design.  These hubs Will Not work on the T-Maxx or E-Maxx.

109,-

KJØP
  • klarna-dark.png
  • vipps-orange.png
  • mastercard-full.png
  • visa.png
  • paypal.png