Traxxas

Rustler VXL

Populært i denne kategorien

Hovedbilde RPM 70662 Wide Front A-Arms Black Rustler/Stampede

RPM 70662 Wide Front A-Arms Black Rustler/Stampede

Art.nr: 70662

Copied

These are the optional RPM Wide Front A-Arms for the Traxxas Electric Rustler and 2WD Stampede. FEATURES Composite nylon construction Widens front wheel stance by almost 1-1/4" (31.8mm) for greater stability Wide front A-arms extend the front width by exactly the difference in offset between the front and rear wheels INCLUDES Left and Right Wide Front A-Arms with Instruction Sheet REQUIREMENTS Longer turnbuckle and camber links; Rustler XL-5: RPM Screw Kit Traxxas Long Camber Links Traxxas Long Toe Links Stampede XL-5: RPM Screw Kit Traxxas Long Camber Links Traxxas Long Toe Links Rustler VXL: RPM Screw Kit Traxxas Long Camber Links Traxxas Long Toe Links Stampede VXL: Traxxas Long Toe Links One pair of front wheels, used to replace rear wheels, for proper alignment

199,-

Hovedbilde RPM 70664 Wide Front A-Arms Green Rustler/Stampede

RPM 70664 Wide Front A-Arms Green Rustler/Stampede

Art.nr: 70664

Copied

Wide Front A-arms for the Traxxas electric Rustler & electric Stampede 2wd Quick Notes: – fits all versions of the electric Rustler & electric Stampede 2wd – replaces stock Traxxas #3631 – See “Tech Notes” below for important fitment information – #70680 Screw Kit for XL-5 models Description Are you looking to add some serious stability to your electric Rustler or Stampede 2wd? Look no further! RPM has a new set of wide front A-arms that will push your front wheels out there almost 1-1/4” (31.8mm) of total width for some serious stability-adding performance. Our Wide Front A-arms extend the front width by exactly the difference in offset between the front and rear wheels. All you need to do is get a second set of “front” wheels and bolt them to the rear to align the front and rear tires and you’re good to go! No expensive prefabricated widening kits or time-consuming conversions. It’s as easy as replacing your stock A-arms with RPM wide A-arms, swap the turnbuckles and camber links for longer versions (not included see “Tech Notes” below) and bolt on a new set of rear wheels! It couldn’t be easier. You already know RPM A-arms are the toughest molded a-arms in the R/C industry (gram for gram, stronger than aluminum as well)! Each RPM A-arm is molded from our trademark blend of nearly indestructible nylons. Tech Notes: RPM wide A-arms for the Traxxas Rustler & Stampede 2wd fit all electric versions of these models, although additional parts (not included) are required for completion as listed here: Rustler XL-5: 1 – RPM Screw Kit #70680, 1 – Traxxas #3643 (long camber links), 1 – Traxxas #3645 (long toe links) & 1 pair of front wheels (used to replace rear wheels). Stampede XL-5, Craniac & Skully: 1 – RPM Screw Kit #70680, 1 – Traxxas #3643 (long camber links), 1 – Traxxas #2338 (long toe links) & 1 pair of front wheels (used to replace rear wheels). Rustler VXL: 1 – Traxxas #3643 (long camber links), 1 – Traxxas #3645 (long toe links) & 1 pair of front wheels (used to replace rear wheels). Stampede VXL: 1 – Traxxas #2338 (long toe links) & 1 pair of front wheels (used to replace rear wheels).

149,-

Hovedbilde RPM 70812 Rear Bumper for Rustler 2WD - ...

Hovedbilde RPM 70812 Rear Bumper for Rustler 2WD - ...

RPM 70812 Rear Bumper for Rustler 2WD - ...

Art.nr: 70812

Copied

RPM Rear Bumper for Rustler 2WD - Black Compatible with Traxxas or RPM Rear Bumper Mounts (not included) / Not compatible with the Nitro Rustler Quick Notes: Works with or without a Wheelie Bar (not included) Compatible with Traxxas or RPM Rear Bumper Mounts (not included) Available in Black, Green, Blue or Pink Not compatible with the Nitro Rustler Are you looking for an actual rear bumper for your electric Rustler? We have you covered! Our Rustler rear bumper is designed to protect the rear of the chassis, the motor and the body, all while still allowing the use of a stock Traxxas Wheelie Bar (Traxxas #3678 – not included). Additionally, if you decide to run without the Wheelie Bar, our rear bumper is so versatile, it’ll adapt and allow either configuration. The RPM Rear Bumper for the electric Rustler is designed tough, with serious impact absorption characteristics built in. With the use of an RPM Rear Bumper Mount (RPM #80902 or RPM #80905 – not included), the protection for the motor becomes nearly indestructible! Each RPM Rear Bumper is made in the USA from our engineering grade nylons and is backed by our limited lifetime warranty against breakage. Tech Notes: RPM Rear Bumpers for the Traxxas Electric Rustler require a bumper mount (either a Traxxas #3677, RPM #80902 or RPM #80905 – not included) or a Wheelie Bar (Traxxas #3678 – not included) to install. If your version did not come with a bumper mount or wheelie bar, you will need to acquire one prior to installing. Works with most known Traxxas Rustler bodies. Aftermarket or non-standard bodies may require trimming for proper fit. Will not fit the Nitro Rustler.

119,-

Hovedbilde RPM 70815 Rear Bumper for Rustler 2WD - ...

Hovedbilde RPM 70815 Rear Bumper for Rustler 2WD - ...

RPM 70815 Rear Bumper for Rustler 2WD - ...

Art.nr: 70815

Copied

RPM Rear Bumper for Rustler 2WD - Blue Compatible with Traxxas or RPM Rear Bumper Mounts (not included) Quick Notes: Works with or without a Wheelie Bar (not included) Compatible with Traxxas or RPM Rear Bumper Mounts (not included) Available in Black, Green, Blue or Pink Not compatible with the Nitro Rustler Are you looking for an actual rear bumper for your electric Rustler? We have you covered! Our Rustler rear bumper is designed to protect the rear of the chassis, the motor and the body, all while still allowing the use of a stock Traxxas Wheelie Bar (Traxxas #3678 – not included). Additionally, if you decide to run without the Wheelie Bar, our rear bumper is so versatile, it’ll adapt and allow either configuration. The RPM Rear Bumper for the electric Rustler is designed tough, with serious impact absorption characteristics built in. With the use of an RPM Rear Bumper Mount (RPM #80902 or RPM #80905 – not included), the protection for the motor becomes nearly indestructible! Each RPM Rear Bumper is made in the USA from our engineering grade nylons and is backed by our limited lifetime warranty against breakage. Tech Notes: RPM Rear Bumpers for the Traxxas Electric Rustler require a bumper mount (either a Traxxas #3677, RPM #80902 or RPM #80905 – not included) or a Wheelie Bar (Traxxas #3678 – not included) to install. If your version did not come with a bumper mount or wheelie bar, you will need to acquire one prior to installing. Works with most known Traxxas Rustler bodies. Aftermarket or non-standard bodies may require trimming for proper fit. Will not fit the Nitro Rustler.

119,-

Hovedbilde RPM 70817 Rear Bumper for Rustler 2WD - ...

Hovedbilde RPM 70817 Rear Bumper for Rustler 2WD - ...

RPM 70817 Rear Bumper for Rustler 2WD - ...

Art.nr: 70817

Copied

RPM Rear Bumper for Rustler 2WD - Pink Compatible with Traxxas or RPM Rear Bumper Mounts (not included) / Not compatible with the Nitro Rustler Quick Notes: Works with or without a Wheelie Bar (not included) Compatible with Traxxas or RPM Rear Bumper Mounts (not included) Available in Black, Green, Blue or Pink Not compatible with the Nitro Rustler Are you looking for an actual rear bumper for your electric Rustler? We have you covered! Our Rustler rear bumper is designed to protect the rear of the chassis, the motor and the body, all while still allowing the use of a stock Traxxas Wheelie Bar (Traxxas #3678 – not included). Additionally, if you decide to run without the Wheelie Bar, our rear bumper is so versatile, it’ll adapt and allow either configuration. The RPM Rear Bumper for the electric Rustler is designed tough, with serious impact absorption characteristics built in. With the use of an RPM Rear Bumper Mount (RPM #80902 or RPM #80905 – not included), the protection for the motor becomes nearly indestructible! Each RPM Rear Bumper is made in the USA from our engineering grade nylons and is backed by our limited lifetime warranty against breakage. Tech Notes: RPM Rear Bumpers for the Traxxas Electric Rustler require a bumper mount (either a Traxxas #3677, RPM #80902 or RPM #80905 – not included) or a Wheelie Bar (Traxxas #3678 – not included) to install. If your version did not come with a bumper mount or wheelie bar, you will need to acquire one prior to installing. Works with most known Traxxas Rustler bodies. Aftermarket or non-standard bodies may require trimming for proper fit. Will not fit the Nitro Rustler.

149,-

Hovedbilde RPM 70942 ESC Cage for the Traxxas VXL-3S (#3355R) ...

RPM 70942 ESC Cage for the Traxxas VXL-3S (#3355R) ...

Art.nr: 70942

Copied

RPM ESC Cage for the Traxxas VXL-3S (#3355R) ESC Fits the Traxxas #3355R VXL-3S ESC only Quick Notes: Fits the Traxxas #3355R VXL-3S ESC only Does not work with Traxxas #3355X ESCs We’ve had numerous requests for an ESC Cage for the #3355R version of the Traxxas VXL-3S ESC since the mounting tabs have been reported to us as weak. Why risk potential damage to your $220 (SRP) speed control when the RPM option is an inexpensive piece of insurance that will prevent those tabs from ever being a problem? Our solution is a simple, yet strong and effective one. We eliminated the use of the two mounting tabs on the ESC in favor of a complete cage system that solidly locks the ESC in place using RPM indestructible nylons. Our ESC Cage is the most effective, durable and best protection for your speed control possible. By completely surrounding and capturing the VXL-3S ESC, damage from broken tabs and ejection from the vehicle has been completely eliminated. The RPM VXL-3S ESC Cage works perfectly even if one or both mounting tabs on the ESC have already been broken or cut off! Now there’s no reason to rely on unpredictable adhesives or zip ties to retain your speed controller when our ESC Cage will lock it in place with 100% confidence each and every time! Each RPM ESC Cage is made from our incredibly strong, ultra lightweight blend of engineering grade nylons and factory-backed by our industry-leading limited lifetime warranty. RPM molded products are made with pride in the USA! Tech Notes: RPM VXL-3S ESC Cages are designed for the Traxxas VXL-3S ESC (Traxxas #3355R) only. While our ESC Cage will fit a variety of applications, they have been tested and only guaranteed to fit the following vehicles in stock form only – Stampede 4×4, Slash 4×4, Slash 2WD & Rally. Also fits the following vehicles as long as Traxxas #3725 Mounting Plate (stock item on VXL models) is used – Rustler 2WD, Stampede 2WD & Bandit.

99,-

Hovedbilde RPM 70945 ESC Cage for the Traxxas VXL-3S (#3355R) ...

Hovedbilde RPM 70945 ESC Cage for the Traxxas VXL-3S (#3355R) ...

RPM 70945 ESC Cage for the Traxxas VXL-3S (#3355R) ...

Art.nr: 70945

Copied

RPM ESC Cage -Blue- for the Traxxas VXL-3S (#3355R) ESC Fits the Traxxas #3355R VXL-3S ESC only Quick Notes: Fits the Traxxas #3355R VXL-3S ESC only Does not work with Traxxas #3355X ESCs We’ve had numerous requests for an ESC Cage for the #3355R version of the Traxxas VXL-3S ESC since the mounting tabs have been reported to us as weak. Why risk potential damage to your $220 (SRP) speed control when the RPM option is an inexpensive piece of insurance that will prevent those tabs from ever being a problem? Our solution is a simple, yet strong and effective one. We eliminated the use of the two mounting tabs on the ESC in favor of a complete cage system that solidly locks the ESC in place using RPM indestructible nylons. Our ESC Cage is the most effective, durable and best protection for your speed control possible. By completely surrounding and capturing the VXL-3S ESC, damage from broken tabs and ejection from the vehicle has been completely eliminated. The RPM VXL-3S ESC Cage works perfectly even if one or both mounting tabs on the ESC have already been broken or cut off! Now there’s no reason to rely on unpredictable adhesives or zip ties to retain your speed controller when our ESC Cage will lock it in place with 100% confidence each and every time! Each RPM ESC Cage is made from our incredibly strong, ultra lightweight blend of engineering grade nylons and factory-backed by our industry-leading limited lifetime warranty. RPM molded products are made with pride in the USA! Tech Notes: RPM VXL-3S ESC Cages are designed for the Traxxas VXL-3S ESC (Traxxas #3355R) only. While our ESC Cage will fit a variety of applications, they have been tested and only guaranteed to fit the following vehicles in stock form only – Stampede 4×4, Slash 4×4, Slash 2WD & Rally. Also fits the following vehicles as long as Traxxas #3725 Mounting Plate (stock item on VXL models) is used – Rustler 2WD, Stampede 2WD & Bandit.

129,-

Hovedbilde RPM 73272 Black ESC Cage for Castle Sidewinder 3 & ...

Hovedbilde RPM 73272 Black ESC Cage for Castle Sidewinder 3 & ...

RPM 73272 Black ESC Cage for Castle Sidewinder 3 & ...

Art.nr: 73272

Copied

ESC Cage for the Castle Sidewinder 3 & Sidewinder SCT Quick Notes: – works with Castle Sidewinder ESCs #010-0115-00, # 010-0115-01, # 010-0115-02, # 010-0115-03, # 010-0115-04 & # 010-0123-00 – fits the Traxxas Slash 2wd, Slash 2wd LCG, Slash 4×4, Slash 4×4 LCG, Stampede 4×4 & Rally – also fits the Stampede 2wd, Rustler & Bandit – see “Tech Notes” below Quick Links: – available in Black & Blue Description The RPM ESC Cage for both the Castle Sidewinder 3 & Sidewinder SCT ESCs fits in the stock location on the Traxxas Slash 2wd, Slash 2wd LCG, Slash 4×4, Slash 4×4 LCG, Stampede 4×4 & Rally, while also working on other Traxxas 1/10th scale vehicles as well (see “Tech Notes” below). Our cage allows the ESC to be run with or without a fan. It encases the ESC body only, leaving the entire ESC fan free to do its job. Furthermore, we left air channels along the sides of the ESC to allow air movement along the sides of the case, helping to keep the ESC cool. Each ESC Cage is designed to simplify ESC installation and maintenance of the vehicle. Two screws hold the entire assembly to the chassis, that’s it! No more struggling with gooey double-sided tape to remove the ESC to clean your vehicle or transfer the electronics to another car. It’s so quick, you can transfer the entire assembly from one vehicle to the next in about a minute! We include a separate, encased on / off switch mount that bolts directly to our cage in one of four locations / orientations for extreme versatility. Since the switch attaches to the cage, no extra time is needed to remove it during maintenance or if you decide to swap the ESC between vehicles. Alternately, you can mount the switch anywhere you’d like simply by drilling and tapping two 2mm holes. Each RPM ESC Cage is manufactured from our ridiculously tough blend of engineering grade nylons for a lifetime of worry-free performance. Each cage is molded in blue or black and backed by our limited lifetime warranty against breakage. Tech Notes: The RPM ESC Cage for the Sidewinder 3 & Sidewinder SCT series ESCs works with Castle Sidewinder #010-0115-00, # 010-0115-01, # 010-0115-02, # 010-0115-03, # 010-0115-04 & # 010-0123-00. While our ESC Cage will fit a variety of applications, they have been tested and guaranteed to fit the following Traxxas vehicles in stock form only – Stampede 4×4, Slash 4×4, Slash 4×4 LCG, Slash 2wd, Slash 2wd LCG, Rally, Stampede VXL 2wd, Rustler VXL & Bandit VXL. Also fits the following vehicles as long as Traxxas #3725 Mounting Plate is used – Rustler XL-5, Stampede XL-5 2wd, Craniac, Skully & Bandit XL-5.

99,-

Hovedbilde RPM 73612 Hybrid Gearbox Housing/Rear Mounts Black

RPM 73612 Hybrid Gearbox Housing/Rear Mounts Black

Art.nr: 73612

Copied

Gearbox Housing and Rear Mounts for the Traxxas Slash 2wd, e-Rustler, e-Stampede & Bandit Quick Notes: – fits the Traxxas Slash 2wd, Bandit, electric Rustler & electric Stampede 2wd – replaces stock Traxxas #3691 & #3691A – hybrid nylon / aluminum for a lightweight, yet strong gearbox – intuitive mounting system allows individual removal of the gearbox or A-arm mounts – matching Gear Cover also available – replacement Rear Mounts available Description The RPM Hybrid Gearbox Housing and Rear Mounts for Traxxas 2wd vehicles is designed to solve a multitude of issues with stock and other aftermarket transmission housings. Our gearbox housing and mounts are a blend of aluminum and molded nylon parts for the perfect combination of strength, durability and heat dissipation. Check out this awesome list of included features: Aluminum Motor Plate: Manufactured in the USA from 3mm thick, 6061 T6 aluminum for serious strength and durability. Locks in gear mesh for worry-free pinion to spur settings, eliminating fears of exploding spur and pinion gears from an overheated stock transmission case. Offers significant motor heat dissipation for cooler motor temperatures, unlike stock plastic motor plates that insulate the motor. Not integrated with the rear bumper mounts, meaning rear impacts will not bend the motor plate, (when used with a rear bumper or bumper mounting system such as RPM #80902 or #80905). Molded Gearbox Housings: Molded from our blend of bulletproof nylons in three popular color choices for guaranteed durability, strength and style. Retains stock bumper mounting holes for positive, solid support of any bumper or wheelie bars you may choose. Retains a stock “cover” for the motor, adding motor protection where most aftermarket housings leave the motor completely exposed to rear impacts. We modified our housing to eliminate the huge bottom hole in the stock housing, keeping your internal gears cleaner longer. Quiet! With a completely enclosed gearbox housing, you’ll no longer have the loudest transmission on the track. Redesigned exterior features are smoother; making it less likely dirt will adhere or build up on the case. Separate housing and rear mounts means transmission maintenance won’t affect suspension settings. Molded Rear Mounts (0° & 3° Rear Mounts Included) Separate from the gearbox housing and easy to access. Each mount is individually accessible and removable without removing the transmission or vice versa. Simply unbolt 2 screws (and a hinge pin) to remove an A-arm mount or 6 screws to remove the transmission! Sold with two sets of rear mounts in each package – 0° and 3° rear mounts are included. Molded from the RPM blend of ultra durable, long lasting, bulletproof nylons. Molded mounts means tighter tolerances and less slop than with machined components for better camber and toe angle retention. Each RPM Gearbox Housing kit is available in black, green or blue and comes will all necessary mounting hardware and instructions. Whether racing or bashing, the RPM Gearbox Housing is one of the least expensive yet most valuable options you can buy! Every RPM Gearbox Housing kit is proudly designed and manufactured in the USA! Get yours today! Tech Notes: RPM Gearbox Housings do not include internal components (gears bearings, shafts, etc.). Internal components (either stock or aftermarket) must be transferred to the RPM Gearbox Housing from the stock Traxxas transmission. RPM Gearbox Housings replace stock Traxxas #3691 (or #3691A). Due to the amount of strengthening material we added to the rear mounts, some modification of stock a-arms may be needed to allow free suspension movement. This slight interference issue is nonexistent when used with RPM rear a-arms. Slash 2wd LCG Chassis Notes: The Traxxas Slash LCG Chassis is slightly longer than the standard chassis so some modification of the back end may be necessary. A 45° chamfer, a radius or shortening the chassis by a small amount corrects the issue.

399,-

449,-

-11%

Hovedbilde RPM 73614 Hybrid Gearbox Housing/Rear Mounts Green

RPM 73614 Hybrid Gearbox Housing/Rear Mounts Green

Art.nr: 73614

Copied

This is the optional RPM Hybrid Gearbox Housing in Green for the Traxxas 1/10 scale 2WD Slash, Stampede, E-Rustler and Bandit. FEATURES 0.12" (3mm) thick 6061 T6 aluminum motor plate offers strength to lock in gear mesh, and better heat dissipation than stock plastic motor plate Motor plate is separate from rear bumper mounts eliminating damage to the plate in the event of a rear collision Molded nylon gearbox housing with stock bumper mounting holes Separate housing and rear mounts allow transmission maintenance without affecting suspension settings 0° and 3° molded rear mounts offer tighter tolerances and less slop than machined components for better camber and toe angle retention INCLUDES Two Gearbox Housings, Motor Plate, two 0° and two 3° Rear Mounts and Instructions

379,-

399,-

-5%

Hovedbilde RPM 73752 Front Bulkhead Black 1/10 Traxxas 2WD

RPM 73752 Front Bulkhead Black 1/10 Traxxas 2WD

Art.nr: 73752

Copied

Front Bulkhead for most 1:10 scale Traxxas 2wd Vehicles Quick Notes: – replaces stock Traxxas #2530 & #2530A – fits the Slash 2wd, Nitro Slash, Bandit, electric Rustler, nitro Rustler, nitro Stampede & electric Stampede 2wd (including all Stampede 2wd variants) Description One of the most highly sought-after RPM parts is finally here! The RPM Front Bulkhead for 1:10 scale Traxxas 2wd vehicles is the ultimate in design, strength and durability. Our engineers reviewed the stock front bulkhead and found something curious. The stock front bulkhead does not sit flat, which can seriously affect suspension settings and adjustments! The RPM Front Bulkhead sits flawlessly level, meaning your front kick angle and A-arm angles will be perfect, providing a superior platform for precise suspension adjustments. We also cored out the bottom of the bulkhead. Why? First and foremost, it helps the bulkhead sit flat. Next, it significantly reduces the weight of the bulkhead. Our version is more that 15% lighter* than stock! By coring out the bottom of the bulkhead, it allows a convenient place to stick some modeling clay to adjust the weight bias of the truck. Leave the weight out if you want the front light; add it in if you want it heavier. We also include a handy dust plate to cover the bottom of the bulkhead on vehicles such as the Rustler, Stampede and Bandit that leave the bottom exposed. The dust plate prevents build-up of dirt and debris, which could affect the handling and weight of the truck. Each RPM Front Bulkhead is built from our bulletproof blend of engineering grade nylons, made right here in the USA and comes with our limited lifetime warranty against breakage. If you want strength you can count on and engineering you can trust, look no further than RPM! Tech Notes: RPM Front Bulkheads for 2wd Traxxas 1:10 scale vehicles are stock replacement parts and replace stock Traxxas #2530 & #2530A. This bulkhead fits the following vehicles: Slash 2wd, Nitro Slash, Bandit, electric Rustler, nitro Rustler, nitro Stampede & electric Stampede 2wd (including all Stampede 2wd variants). It does not fit the 4×4 versions of any of these vehicles.

179,-

Hovedbilde RPM 73754 Front Bulkhead Green 1/10 Traxxas 2WD

RPM 73754 Front Bulkhead Green 1/10 Traxxas 2WD

Art.nr: 73754

Copied

Front Bulkhead for most 1:10 scale Traxxas 2wd Vehicles Quick Notes: – replaces stock Traxxas #2530 & #2530A – fits the Slash 2wd, Nitro Slash, Bandit, electric Rustler, nitro Rustler, nitro Stampede & electric Stampede 2wd (including all Stampede 2wd variants) Description One of the most highly sought-after RPM parts is finally here! The RPM Front Bulkhead for 1:10 scale Traxxas 2wd vehicles is the ultimate in design, strength and durability. Our engineers reviewed the stock front bulkhead and found something curious. The stock front bulkhead does not sit flat, which can seriously affect suspension settings and adjustments! The RPM Front Bulkhead sits flawlessly level, meaning your front kick angle and A-arm angles will be perfect, providing a superior platform for precise suspension adjustments. We also cored out the bottom of the bulkhead. Why? First and foremost, it helps the bulkhead sit flat. Next, it significantly reduces the weight of the bulkhead. Our version is more that 15% lighter* than stock! By coring out the bottom of the bulkhead, it allows a convenient place to stick some modeling clay to adjust the weight bias of the truck. Leave the weight out if you want the front light; add it in if you want it heavier. We also include a handy dust plate to cover the bottom of the bulkhead on vehicles such as the Rustler, Stampede and Bandit that leave the bottom exposed. The dust plate prevents build-up of dirt and debris, which could affect the handling and weight of the truck. Each RPM Front Bulkhead is built from our bulletproof blend of engineering grade nylons, made right here in the USA and comes with our limited lifetime warranty against breakage. If you want strength you can count on and engineering you can trust, look no further than RPM! Tech Notes: RPM Front Bulkheads for 2wd Traxxas 1:10 scale vehicles are stock replacement parts and replace stock Traxxas #2530 & #2530A. This bulkhead fits the following vehicles: Slash 2wd, Nitro Slash, Bandit, electric Rustler, nitro Rustler, nitro Stampede & electric Stampede 2wd (including all Stampede 2wd variants). It does not fit the 4×4 versions of any of these vehicles.

159,-

179,-

-11%

Hovedbilde RPM 73755 Front Bulkhead Blue 1/10 Traxxas 2WD

RPM 73755 Front Bulkhead Blue 1/10 Traxxas 2WD

Art.nr: 73755

Copied

Front Bulkhead for most 1:10 scale Traxxas 2wd Vehicles Quick Notes: – replaces stock Traxxas #2530 & #2530A – fits the Slash 2wd, Nitro Slash, Bandit, electric Rustler, nitro Rustler, nitro Stampede & electric Stampede 2wd (including all Stampede 2wd variants) Description: One of the most highly sought-after RPM parts is finally here! The RPM Front Bulkhead for 1:10 scale Traxxas 2wd vehicles is the ultimate in design, strength and durability. Our engineers reviewed the stock front bulkhead and found something curious. The stock front bulkhead does not sit flat, which can seriously affect suspension settings and adjustments! The RPM Front Bulkhead sits flawlessly level, meaning your front kick angle and A-arm angles will be perfect, providing a superior platform for precise suspension adjustments. We also cored out the bottom of the bulkhead. Why? First and foremost, it helps the bulkhead sit flat. Next, it significantly reduces the weight of the bulkhead. Our version is more that 15% lighter* than stock! By coring out the bottom of the bulkhead, it allows a convenient place to stick some modeling clay to adjust the weight bias of the truck. Leave the weight out if you want the front light; add it in if you want it heavier. We also include a handy dust plate to cover the bottom of the bulkhead on vehicles such as the Rustler, Stampede and Bandit that leave the bottom exposed. The dust plate prevents build-up of dirt and debris, which could affect the handling and weight of the truck. Each RPM Front Bulkhead is built from our bulletproof blend of engineering grade nylons, made right here in the USA and comes with our limited lifetime warranty against breakage. If you want strength you can count on and engineering you can trust, look no further than RPM! Tech Notes: RPM Front Bulkheads for 2wd Traxxas 1:10 scale vehicles are stock replacement parts and replace stock Traxxas #2530 & #2530A. This bulkhead fits the following vehicles: Slash 2wd, Nitro Slash, Bandit, electric Rustler, nitro Rustler, nitro Stampede & electric Stampede 2wd (including all Stampede 2wd variants). It does not fit the 4×4 versions of any of these vehicles.

169,-

Hovedbilde RPM 73759 Front Bulkhead Red 1/10 Traxxas 2WD

RPM 73759 Front Bulkhead Red 1/10 Traxxas 2WD

Art.nr: 73759

Copied

Front Bulkhead for most 1:10 scale Traxxas 2wd Vehicles Quick Notes: – replaces stock Traxxas #2530 & #2530A – fits the Slash 2wd, Nitro Slash, Bandit, electric Rustler, nitro Rustler, nitro Stampede & electric Stampede 2wd (including all Stampede 2wd variants) Description One of the most highly sought-after RPM parts is finally here! The RPM Front Bulkhead for 1:10 scale Traxxas 2wd vehicles is the ultimate in design, strength and durability. Our engineers reviewed the stock front bulkhead and found something curious. The stock front bulkhead does not sit flat, which can seriously affect suspension settings and adjustments! The RPM Front Bulkhead sits flawlessly level, meaning your front kick angle and A-arm angles will be perfect, providing a superior platform for precise suspension adjustments. We also cored out the bottom of the bulkhead. Why? First and foremost, it helps the bulkhead sit flat. Next, it significantly reduces the weight of the bulkhead. Our version is more that 15% lighter* than stock! By coring out the bottom of the bulkhead, it allows a convenient place to stick some modeling clay to adjust the weight bias of the truck. Leave the weight out if you want the front light; add it in if you want it heavier. We also include a handy dust plate to cover the bottom of the bulkhead on vehicles such as the Rustler, Stampede and Bandit that leave the bottom exposed. The dust plate prevents build-up of dirt and debris, which could affect the handling and weight of the truck. Each RPM Front Bulkhead is built from our bulletproof blend of engineering grade nylons, made right here in the USA and comes with our limited lifetime warranty against breakage. If you want strength you can count on and engineering you can trust, look no further than RPM! Tech Notes: RPM Front Bulkheads for 2wd Traxxas 1:10 scale vehicles are stock replacement parts and replace stock Traxxas #2530 & #2530A. This bulkhead fits the following vehicles: Slash 2wd, Nitro Slash, Bandit, electric Rustler, nitro Rustler, nitro Stampede & electric Stampede 2wd (including all Stampede 2wd variants). It does not fit the 4×4 versions of any of these vehicles.

159,-

Hovedbilde RPM 73762 ESC Cage Mamba X Black

RPM 73762 ESC Cage Mamba X Black

Art.nr: 73762

Copied

ESC Cage for the Castle Mamba X ESC (fits most Traxxas 1:10 scale vehicles) Quick Notes: – works with Castle Mamba X ESCs #010-0155-00, #010-0155-01, #010-0155-02, #010-0155-03, #010-0155-04, #010-0160-00, #010-0160-01, #010-0161-00 & #010-0161-01 – fits the Traxxas Slash 2wd, Slash 2wd LCG, Slash 4×4, Slash 4×4 LCG, Stampede 4×4 & Rally – also fits the Stampede 2wd, Rustler & Bandit – see “Tech Notes” below Description Our ESC Cage for the Castle Mamba X ESC provides a solid, positive mount to keep your new, and valuable ESC in place even under the most extreme circumstances. It also allows the ESC to be run with or without a fan. It encases the ESC body only, leaving the entire ESC fan free to do its job. Furthermore, we left air channels along both sides of the ESC to allow air movement along the sides of the case, helping to keep the ESC cool. Each RPM ESC Cage is designed to simplify ESC installation and maintenance of the vehicle. Two screws hold the entire assembly to the chassis, that’s it! No more struggling with gooey double-sided tape to remove the ESC to clean your vehicle or transfer the electronics to another car. It’s so easy that you can transfer the entire assembly from one vehicle to the next in about a minute! The two mounting screws can actually be accessed without removing the top from the base making this one of the easiest ESC Cages we manufacture to remove and install. We include a separate, encased on / off switch mount that bolts directly to our cage in one of four locations / orientations for extreme versatility. Since the switch attaches to the cage, no extra time is needed to remove it during maintenance or if you decide to swap the ESC between vehicles. Our ESC Cage for the Castle Mamba X ESC fits in the stock location on the Traxxas Slash 2wd, Slash 2wd LCG, Slash 4×4, Slash 4×4 LCG, Stampede 4×4 & Rally, while also working on other Traxxas 1/10th scale vehicles as well (see “Tech Notes” below). Each RPM ESC Cage is manufactured from our ridiculously tough blend of engineering grade nylons and backed by our limited lifetime warranty against breakage. Don’t trust your investment to double-sided tape or zip ties. One fail and your ESC will eject like a bullet from a gun! Trust a name you’ve known for decades for bulletproof protection – RPM! Tech Notes: The RPM ESC Cage for the Mamba X series ESCs works with #010-0155-00, #010-0155-01, #010-0155-02, #010-0155-03, #010-0155-04, #010-0160-00, #010-0160-01, #010-0161-00 & #010-0161-01. While our ESC Cage will fit a variety of applications, they have been tested and guaranteed to fit the following Traxxas vehicles in stock form only – Stampede 4×4, Slash 4×4, Slash 4×4 LCG, Slash 2wd, Slash 2wd LCG, & Rally. Also fits the following vehicles as long as Traxxas #3725 Mounting Plate (stock item on VXL models) is used – Rustler, Stampede 2wd & Bandit.

169,-

Hovedbilde RPM 80182 Rear A-Arms Black Electric Rustler/Stampede ...

RPM 80182 Rear A-Arms Black Electric Rustler/Stampede ...

Art.nr: 80182

Copied

RPM Rear Suspension Arms for Rustler & Stampede (2WD) - Black Replaces stock Traxxas #3655 & 3655X Quick Notes: Fits 2WD versions of the electric Stampede & Rustler Each A-arm is 7 grams lighter than stock! Eliminates over 0.03” (0.8mm) of slop from the inner arm mount Replaces stock Traxxas #3655 & 3655X RPM rear A-arms for the electric versions of the Traxxas Rustler & Stampede are stronger and more durable than stock versions, yet we’ve also managed to eliminate over 7 grams of weight per arm! That’s 14 grams of unsprung weight eliminated with a single pair of rear RPM A-arms! Coupled with a set of RPM front A-arms, the total weight loss exceeds 24 grams, or almost a full ounce! We accomplished this without creating any weak points nor are our A-arms any more flexible than the stock versions. Additionally, we’ve adjusted the shock mount locations slightly to allow more noticeable tuning adjustments when using the inner or outer shock mount holes (while the center hole remains in its stock location). While we were at it, we eliminated over 0.030” or 1/32” of slop from the inner arm mount and more than 0.010” or slightly less than 1/64” of slop at the outer hinge pin for an ultra-smooth, slop-free suspension system. RPM A-arms for the electric versions of the Traxxas Rustler & Stampede are molded in black, blue, green or red and are sold in pairs – 1 left rear and 1 right rear per package.

149,-

169,-

-12%

Hovedbilde RPM 80184 Rear A-Arms Green Electric Traxxas Stampede ...

RPM 80184 Rear A-Arms Green Electric Traxxas Stampede ...

Art.nr: 80184

Copied

RPM Rear Suspension Arms for Rustler & Stampede (2WD) - Green Replaces stock Traxxas #3655 & 3655X Quick Notes: Fits 2WD versions of the electric Stampede & Rustler Each A-arm is 7 grams lighter than stock! Eliminates over 0.03” (0.8mm) of slop from the inner arm mount Replaces stock Traxxas #3655 & 3655X RPM rear A-arms for the electric versions of the Traxxas Rustler & Stampede are stronger and more durable than stock versions, yet we’ve also managed to eliminate over 7 grams of weight per arm! That’s 14 grams of unsprung weight eliminated with a single pair of rear RPM A-arms! Coupled with a set of RPM front A-arms, the total weight loss exceeds 24 grams, or almost a full ounce! We accomplished this without creating any weak points nor are our A-arms any more flexible than the stock versions. Additionally, we’ve adjusted the shock mount locations slightly to allow more noticeable tuning adjustments when using the inner or outer shock mount holes (while the center hole remains in its stock location). While we were at it, we eliminated over 0.030” or 1/32” of slop from the inner arm mount and more than 0.010” or slightly less than 1/64” of slop at the outer hinge pin for an ultra-smooth, slop-free suspension system. RPM A-arms for the electric versions of the Traxxas Rustler & Stampede are molded in black, blue, green or red and are sold in pairs – 1 left rear and 1 right rear per package.

149,-

169,-

-12%

Hovedbilde RPM 80185 Rear Suspension Arms for Rustler & Stampede ...

RPM 80185 Rear Suspension Arms for Rustler & Stampede ...

Art.nr: 80185

Copied

RPM Rear Suspension Arms for Rustler & Stampede (2WD) - Blue Replaces stock Traxxas #3655 & 3655X Quick Notes: Fits 2WD versions of the electric Stampede & Rustler Each A-arm is 7 grams lighter than stock! Eliminates over 0.03” (0.8mm) of slop from the inner arm mount Replaces stock Traxxas #3655 & 3655X RPM rear A-arms for the electric versions of the Traxxas Rustler & Stampede are stronger and more durable than stock versions, yet we’ve also managed to eliminate over 7 grams of weight per arm! That’s 14 grams of unsprung weight eliminated with a single pair of rear RPM A-arms! Coupled with a set of RPM front A-arms, the total weight loss exceeds 24 grams, or almost a full ounce! We accomplished this without creating any weak points nor are our A-arms any more flexible than the stock versions. Additionally, we’ve adjusted the shock mount locations slightly to allow more noticeable tuning adjustments when using the inner or outer shock mount holes (while the center hole remains in its stock location). While we were at it, we eliminated over 0.030” or 1/32” of slop from the inner arm mount and more than 0.010” or slightly less than 1/64” of slop at the outer hinge pin for an ultra-smooth, slop-free suspension system. RPM A-arms for the electric versions of the Traxxas Rustler & Stampede are molded in black, blue, green or red and are sold in pairs – 1 left rear and 1 right rear per package.

149,-

169,-

-12%

Hovedbilde RPM 80187 RPM Rear Suspension Arms for Rustler & ...

RPM 80187 RPM Rear Suspension Arms for Rustler & ...

Art.nr: 80187

Copied

RPM Rear Suspension Arms for Rustler & Stampede (2WD) - Pink Replaces stock Traxxas #3655 & 3655X Quick Notes: Fits 2WD versions of the electric Stampede & Rustler Each A-arm is 7 grams lighter than stock! Eliminates over 0.03” (0.8mm) of slop from the inner arm mount Replaces stock Traxxas #3655 & 3655X RPM rear A-arms for the electric versions of the Traxxas Rustler & Stampede are stronger and more durable than stock versions, yet we’ve also managed to eliminate over 7 grams of weight per arm! That’s 14 grams of unsprung weight eliminated with a single pair of rear RPM A-arms! Coupled with a set of RPM front A-arms, the total weight loss exceeds 24 grams, or almost a full ounce! We accomplished this without creating any weak points nor are our A-arms any more flexible than the stock versions. Additionally, we’ve adjusted the shock mount locations slightly to allow more noticeable tuning adjustments when using the inner or outer shock mount holes (while the center hole remains in its stock location). While we were at it, we eliminated over 0.030” or 1/32” of slop from the inner arm mount and more than 0.010” or slightly less than 1/64” of slop at the outer hinge pin for an ultra-smooth, slop-free suspension system. RPM A-arms for the electric versions of the Traxxas Rustler & Stampede are molded in black, blue, green or red and are sold in pairs – 1 left rear and 1 right rear per package.

149,-

169,-

-12%

Hovedbilde RPM 80189 Rear A-Arms Rustler/Stampede 2WD Red ...

RPM 80189 Rear A-Arms Rustler/Stampede 2WD Red ...

Art.nr: 80189

Copied

RPM Rear Suspension Arms for Rustler & Stampede (2WD) - Red Replaces stock Traxxas #3655 & 3655X Quick Notes: Fits 2WD versions of the electric Stampede & Rustler Each A-arm is 7 grams lighter than stock! Eliminates over 0.03” (0.8mm) of slop from the inner arm mount Replaces stock Traxxas #3655 & 3655X RPM rear A-arms for the electric versions of the Traxxas Rustler & Stampede are stronger and more durable than stock versions, yet we’ve also managed to eliminate over 7 grams of weight per arm! That’s 14 grams of unsprung weight eliminated with a single pair of rear RPM A-arms! Coupled with a set of RPM front A-arms, the total weight loss exceeds 24 grams, or almost a full ounce! We accomplished this without creating any weak points nor are our A-arms any more flexible than the stock versions. Additionally, we’ve adjusted the shock mount locations slightly to allow more noticeable tuning adjustments when using the inner or outer shock mount holes (while the center hole remains in its stock location). While we were at it, we eliminated over 0.030” or 1/32” of slop from the inner arm mount and more than 0.010” or slightly less than 1/64” of slop at the outer hinge pin for an ultra-smooth, slop-free suspension system. RPM A-arms for the electric versions of the Traxxas Rustler & Stampede are molded in black, blue, green or red and are sold in pairs – 1 left rear and 1 right rear per package.

149,-

169,-

-12%

Hovedbilde RPM 80242 Front A-Arms Black Rustler/Stampede/Slash ...

Hovedbilde RPM 80242 Front A-Arms Black Rustler/Stampede/Slash ...

RPM 80242 Front A-Arms Black Rustler/Stampede/Slash ...

Art.nr: 80242

Copied

RPM Front Arms for the 2WD: Slash, Nitro Slash, Rustler & Stampede - Black Replaces stock Traxxas #3631 Quick Notes: Fits all versions of the Traxxas 2WD: Slash, Nitro Slash, Stampede & Rustler Nearly 25% lighter than stock Replaces stock Traxxas #3631 RPM front A-arms for the Traxxas Slash 2wd, Nitro Slash, e-Rustler & e-Stampede 2wd are built to withstand some of the toughest abuse. Incredibly, we were able to shave some unwanted unsprung weight as well. RPM Front A-arms are nearly 25% lighter than stock versions of the same A-arms, yet the RPM versions are backed with our world-renowned breakage warranty. Additionally, we’ve increased clearance areas in the outer portion of the A-arms to allow increased droop travel when used in conjunction with RPM oversized bearing carriers (RPM #80372 & #80382). RPM front A-arms for the Electric versions of the Traxxas Slash, Rustler & Stampede are sold in pairs and are available in black, green, blue and red. These A-arms are molded with what is fast becoming an RPM trademark design of angled leading and trailing edges to reduce frontal edge mass and improve the a-arm’s ability to ride up and over tall obstacles instead of slamming into them. RPM A-arms are extremely rigid for a superior ride and stability over the roughest tracks and terrain.

149,-

Hovedbilde RPM 80244 Front A-Arms Green Slash/Rustler/Elec ...

Hovedbilde RPM 80244 Front A-Arms Green Slash/Rustler/Elec ...

RPM 80244 Front A-Arms Green Slash/Rustler/Elec ...

Art.nr: 80244

Copied

RPM Front Arms for the 2WD: Slash, Nitro Slash, Rustler & Stampede - Green Replaces stock Traxxas #3631 Quick Notes: Fits all versions of the Traxxas 2WD: Slash, Nitro Slash, Stampede & Rustler Nearly 25% lighter than stock Replaces stock Traxxas #3631 RPM front A-arms for the Traxxas Slash 2wd, Nitro Slash, e-Rustler & e-Stampede 2wd are built to withstand some of the toughest abuse. Incredibly, we were able to shave some unwanted unsprung weight as well. RPM Front A-arms are nearly 25% lighter than stock versions of the same A-arms, yet the RPM versions are backed with our world-renowned breakage warranty. Additionally, we’ve increased clearance areas in the outer portion of the A-arms to allow increased droop travel when used in conjunction with RPM oversized bearing carriers (RPM #80372 & #80382). RPM front A-arms for the Electric versions of the Traxxas Slash, Rustler & Stampede are sold in pairs and are available in black, green, blue and red. These A-arms are molded with what is fast becoming an RPM trademark design of angled leading and trailing edges to reduce frontal edge mass and improve the a-arm’s ability to ride up and over tall obstacles instead of slamming into them. RPM A-arms are extremely rigid for a superior ride and stability over the roughest tracks and terrain.

149,-

Hovedbilde RPM 80245 Front Arms for the 2WD: Slash, Nitro Slash, ...

RPM 80245 Front Arms for the 2WD: Slash, Nitro Slash, ...

Art.nr: 80245

Copied

RPM Front Arms for the 2WD: Slash, Nitro Slash, Rustler & Stampede - Blue Replaces stock Traxxas #3631 Quick Notes: Fits all versions of the Traxxas 2WD: Slash, Nitro Slash, Stampede & Rustler Nearly 25% lighter than stock Replaces stock Traxxas #3631 RPM front A-arms for the Traxxas Slash 2wd, Nitro Slash, e-Rustler & e-Stampede 2wd are built to withstand some of the toughest abuse. Incredibly, we were able to shave some unwanted unsprung weight as well. RPM Front A-arms are nearly 25% lighter than stock versions of the same A-arms, yet the RPM versions are backed with our world-renowned breakage warranty. Additionally, we’ve increased clearance areas in the outer portion of the A-arms to allow increased droop travel when used in conjunction with RPM oversized bearing carriers (RPM #80372 & #80382). RPM front A-arms for the Electric versions of the Traxxas Slash, Rustler & Stampede are sold in pairs and are available in black, green, blue and red. These A-arms are molded with what is fast becoming an RPM trademark design of angled leading and trailing edges to reduce frontal edge mass and improve the a-arm’s ability to ride up and over tall obstacles instead of slamming into them. RPM A-arms are extremely rigid for a superior ride and stability over the roughest tracks and terrain.

109,-

Hovedbilde RPM 80247 Front Arms for the 2WD: Slash, Nitro Slash, ...

RPM 80247 Front Arms for the 2WD: Slash, Nitro Slash, ...

Art.nr: 80247

Copied

RPM Front Arms for the 2WD: Slash, Nitro Slash, Rustler & Stampede - Pink Replaces stock Traxxas #3631 Quick Notes: Fits all versions of the Traxxas 2WD: Slash, Nitro Slash, Stampede & Rustler Nearly 25% lighter than stock Replaces stock Traxxas #3631 RPM front A-arms for the Traxxas Slash 2wd, Nitro Slash, e-Rustler & e-Stampede 2wd are built to withstand some of the toughest abuse. Incredibly, we were able to shave some unwanted unsprung weight as well. RPM Front A-arms are nearly 25% lighter than stock versions of the same A-arms, yet the RPM versions are backed with our world-renowned breakage warranty. Additionally, we’ve increased clearance areas in the outer portion of the A-arms to allow increased droop travel when used in conjunction with RPM oversized bearing carriers (RPM #80372 & #80382). RPM front A-arms for the Electric versions of the Traxxas Slash, Rustler & Stampede are sold in pairs and are available in black, green, blue and red. These A-arms are molded with what is fast becoming an RPM trademark design of angled leading and trailing edges to reduce frontal edge mass and improve the a-arm’s ability to ride up and over tall obstacles instead of slamming into them. RPM A-arms are extremely rigid for a superior ride and stability over the roughest tracks and terrain.

139,-

Hovedbilde RPM 80249 Front A-Arms Slash 2WD/Rustler/Stampede 2WD ...

RPM 80249 Front A-Arms Slash 2WD/Rustler/Stampede 2WD ...

Art.nr: 80249

Copied

RPM Front Arms for the 2WD: Slash, Nitro Slash, Rustler & Stampede - Red Replaces stock Traxxas #3631 Quick Notes: Fits all versions of the Traxxas 2WD: Slash, Nitro Slash, Stampede & Rustler Nearly 25% lighter than stock Replaces stock Traxxas #3631 RPM front A-arms for the Traxxas Slash 2wd, Nitro Slash, e-Rustler & e-Stampede 2wd are built to withstand some of the toughest abuse. Incredibly, we were able to shave some unwanted unsprung weight as well. RPM Front A-arms are nearly 25% lighter than stock versions of the same A-arms, yet the RPM versions are backed with our world-renowned breakage warranty. Additionally, we’ve increased clearance areas in the outer portion of the A-arms to allow increased droop travel when used in conjunction with RPM oversized bearing carriers (RPM #80372 & #80382). RPM front A-arms for the Electric versions of the Traxxas Slash, Rustler & Stampede are sold in pairs and are available in black, green, blue and red. These A-arms are molded with what is fast becoming an RPM trademark design of angled leading and trailing edges to reduce frontal edge mass and improve the a-arm’s ability to ride up and over tall obstacles instead of slamming into them. RPM A-arms are extremely rigid for a superior ride and stability over the roughest tracks and terrain

109,-

Viser 1 til 25 (av 56 produkter)