Hopp til innhold

Blackweek 2026

 
Art.nr: 34703T2B
Copied
Nyt kraftig pickup-ytelse i realistisk 1/10-skala!   Med robuste dekk og understell for å håndtere ulendt terreng og et stort lasteplan bak, er pickuper etterspurt i hele Nord-Amerika, Sørøst-Asia, Afrika og Australia, og mange populære pickuper har blitt gjenskapt som R/C-modeller. Toyota utviklet Tacoma hovedsakelig for det nordamerikanske markedet, og den har fortsatt å selge godt siden utgivelsen i 1995. Denne modellen er basert på 3. generasjon Tacoma som først fikk stor anerkjennelse i 2016 på grunn av sin aggressive stil og praktiske egenskaper. Toppen av serien Tacoma TRD Pro har blitt gjenskapt av Kyosho med et tøft 1/10-skala chassis i en Readyset-pakke. Kyoshos støpehåndverk gjengir TRD Pro-kroppen plettfritt i lett, men stiv polykarbonatharpiks med styrke for hard terrengkjøring. Basert på offroad KB10-chassiset passer den lange akselavstanden og den korte slitebanen til KB10L-chassiset perfekt til karosseriet. Det akseldrevne 4WD-systemet overfører pålitelig kraften til den børsteløse TORX10L-motoren for å nå topphastigheter på rundt 75 km/t under ledelse av ESC (Electronic Speed Control) og et kompatibelt 3S (11.1V) lipo-batteri. Denne praktiske Readyset-pakken inneholder moroa fra en ultraskala pickup på et dynamisk terrengchassis med en finish som i kvalitet ligner på premium-modeller som kun er skjermet. ●Readyset inkluderer R/C-system forhåndsinstallert på chassiset og en pistolgrepssender. ●Forhåndsmalt og montert "Toyota Tacoma TRD Pro" ultraskala karosseri fanger fullt ut formen til den originale lastebilen. ● Nydesignede kroppsfester skjuler kroppsstifter fra utsiden for å realisere en høyere skalafølelse. ●LED-lys (selges separat) kan festes til lysbøttene foran og bak. Skalafølelsen forsterkes ytterligere når 4 lys foran og 2 baklys (4 hvis ryggelys er installert) lyser fullt ut. Anbefalt: 4 lys foran, 2 baklykter (97054-4CR x 1, 97054-2B x 1) / Med reverslys, 4 lys foran, 4 baklykter (97054-4B x 1, 97054-4CR x 1) ●Fulltids 4WD KB10L-chassis kan håndtere røffe veier så vel som på vei og flatt skitt. ●Batteriholder kompatibel med 3S-batterier. Batteriet er festet med et belte som er lett å ta av og på. ●Inkluderer kraftig TORX 10L børsteløs motor og vanntett BRAINZ 10 + børsteløs ESC. ●3 differensialdesign for forbedret løpsstabilitet. Olje #10000 er forhåndsfylt i senterdiff og #5000 olje foran og bak. ●Fulle kulelager (22) utstyrt for optimal driveffektivitet og holdbarhet. ●Hvert gir, mottaker er innelukket i en forseglet boks for å forhindre kompromisser fra sand og skitt under kjøring. ●Pistolgrep type Syncro KT-231P+ sender inkludert muliggjør ulike innstillingsendringer. ●Batterilader og batteri for chassis pluss 4 x AA-batterier for sender må kjøpes separat. Den lave og brede formen på polykarbonatkroppen er ulastelig gjenskapt med den unike TRD Pro frontgrillen og lette bøtter for å forbedre den tredimensjonale effekten. Slitesterk 1,5 mm PC-kropp. Karosserifester foran og bak sikrer karosseriet fra under chassiset (bildet viser fronten) slik at skalaens utseende ikke kompromitteres av synlige karosseristolper eller pinner på utsiden av karosseriet. Basert på 1/10-skalaen Mad Wagon bush-basher offroad-chassis, har KB10L en utvidet akselavstand og forkortede fjæringsarmer med stabiliteten til akseltypen 4WD. 4WD-system av akseltype med girkasse med senterdifferensial reduserer motorrotasjonen for optimal kraftoverføring til for- og bakhjul. Nytt langt aluminiumchassis gir pålitelig trekkraft selv på overflater med lite grep. Oljedempere demper tilbakemeldinger fra veibanen pålitelig for å stabilisere chassiset under kjøring. Forhåndsmonterte støtdempere er forhåndsfylte med olje og fjærhastighet (hardhet) er optimert for KB10L-chassiset. Sperrestenger på fjæring og styring gjør det enkelt å justere camber- og tåvinkelen. Teleskopiske universalaksler i harpiks er utskiftbare mellom foran og bak for deler og vedlikeholdseffektivitet. Nylig vedtatt senterdifferensial i KB10L-chassiset optimerer kraftfordelingen til for- og bakhjul gjennom hjørner for jevn svingytelse. IF245 cylindrisk stålhjul for 1/8-skala buggy Inferno NEO-serien kan installeres som en valgfri del.(Et BRG005-lager kreves separat.) Utstyrt med sintrede metall 4-fasede differensialgir foran og bak med kapasitet til å håndtere høyeffekts børsteløse motorer. IS117 hardt vinkelgir fra 1/8-modellen Inferno NEO ST 3.0 kan installeres som en valgfri del.(BRG005-lager kreves separat.) Nydesignede hjul og dekk viser overlegent grep, både på og terreng. Dekkmønster og hjuldesign gjenskaper den faktiske kjøretøystilen for en full følelse av skalarealisme.   TEKNISKE DATA ■Lengde 572mm ■Bredde 274mm ■Høyde 214mm ■Akkullavstand 340mm ■Slitebane F/R 224mm ■Dekk(F & R) φ110 x 47 mm ■Girforhold 10.41:1 ■Vekt 3410 g (ca.) ■Motor TORX10L Børsteløs Motor kv2850   ●Fabrikkmontert chassis ●Forkuttet og malt kropp komplett med dekaler påført ●2,4GHz Syncro KT-231P+ sender ●1,5 mm/2,0 mm/2,5 mm L-formede sekskantnøkler ●Kvernøkkel ●4/5/5,5/7/10mm Integrert skiftenøkkel   Nødvendig for drift ● AA-batterier x 4 for sender ●Batteri for kjøring (2-3S LiPo batteri *Installerbart batteri størrelse 143x47x30mm) ●Lader for LiPo-batteri   English text:   Enjoy powerful pickup truck performance in realistic 1/10 scale!   With rugged tires and undercarriage to handle rough terrain and a large rear cargo bed, pickup trucks are in high demand throughout North America, Southeast Asia, Africa, and Australia and many popular pickup trucks have been recreated as R/C models. Toyota developed the Tacoma mainly for the North American market and it has continued to sell well since its release in 1995. This model is based on the 3rd generation Tacoma which first appeared to much acclaim in 2016 due to its aggressive styling and practicality. The top of the range Tacoma TRD Pro has been recreated by Kyosho with a tough 1/10 scale chassis in a Readyset package. Kyosho’s molding craftmanship immaculately reproduces the TRD Pro body in lightweight but rigid polycarbonate resin with the strength for hard off-road driving. Based on the off-road KB10 chassis, the long wheelbase and short tread of the KB10L chassis matches the body perfectly. The shaft-driven 4WD system reliably transfers the brute power of the TORX10L brushless motor to reach top speeds of about 75km/h under the management of the ESC (Electronic Speed Control) and a compatible 3S (11.1V) lipo battery. This convenient Readyset package contains the fun of an ultra-scale pickup truck on a dynamic off-road chassis with a finish similar in quality to premium display-only models. ●Readyset includes R/C system pre-installed on the chassis and a pistol-grip transmitter. ●Pre-painted and assembled "Toyota Tacoma TRD Pro" ultra-scale body fully captures the form of the original truck. ●Newly designed body mounts conceal body pins from the outside to realize a higher sense of scale. ●LED lights (sold separately) can be attached to the front and rear light buckets. The scale feeling is further enhanced when 4 front lights and 2 rear lights (4 if reverse lights installed) are fully lit. Recommended: Front 4 lights, Rear 2 lights (97054-4CR x 1, 97054-2B x 1) / With reverse lights, Front 4 lights, Rear 4 lights (97054-4B x 1, 97054-4CR x 1) ●Full-time 4WD KB10L chassis can handle rough roads as well as on-road and flat dirt. ●Battery holder compatible with 3S size batteries. The battery is fixed with a belt that is easy to take off and on. ●Includes powerful TORX 10L brushless motor and waterproof BRAINZ 10 + brushless ESC. ●3 differential design for enhanced running stability. #10000 oil is pre-filled in the center diff and #5000 oil in the front and rear diffs. ●Full ball bearings (22) equipped for optimal drive efficiency and durability. ●Each gear unit, receiver are enclosed in a sealed box to prevent compromise from sand and dirt while driving. ●Pistol grip type Syncro KT-231P+ transmitter included allows various setting changes. ●Battery charger and battery for chassis plus 4 x AA batteries for transmitter must be purchased separately. Low & wide shape of the polycarbonate body has been immaculately recreated with the unique TRD Pro front grill and light buckets to enhance the 3-dimensional effect. Durable 1.5mm PC body. Body mounts on front and rear secure the body from under the chassis (photo shows front) so scale appearance is not compromised by exposed body post or pins on the outside of the body. Based on the 1/10 scale Mad Wagon bush-basher off-road chassis, the KB10L has an extended wheelbase and shortened suspension arms with the stability of the shaft-type 4WD. Shaft-type 4WD system incorporating gearbox with center differential reduces motor rotation for optimal power transfer to front and rear wheels. New long aluminum chassis produces reliable traction even on low-grip surfaces. Oil shocks reliably attenuate feedback from the road surface to stabilize the chassis while driving. Pre-mounted shocks are pre-filled with oil and spring rate (hardness) has been optimized for the KB10L chassis. Turnbuckle rods on suspension and steering make it easy to adjust the camber and toe angle. Telescoping resin universal shafts are interchangeable between front and rear for parts and maintenance efficiency. Newly adopted center differential in the KB10L chassis optimizes power distribution to front and rear wheels through corners for smooth turning performance. IF245 steel spur gear for the 1/8 scale buggy Inferno NEO series can be installed as an optional part.(One BRG005 bearing is required separately.) Equipped with sintered metal 4-bevel differential gears on the front and rear with the capacity to handle high-power brushless motors. IS117 hard bevel gear from the 1/8 model Inferno NEO ST 3.0 can be installed as an optional part.(BRG005 bearing is required separately.) Newly designed wheels and tires demonstrate superior grip, both on and off-road. Tire pattern and wheel design replicate the actual vehicle style for a full sense of scale realism.   ■Length 572mm ■Width 274mm ■Height 214mm ■Wheelbase 340mm ■Tread F/R 224mm ■Tires(F & R) φ110 x 47mm ■Gear Ratio 10.41:1 ■Weight 3,410g (approx.) ■Motor TORX10L Brushless Motor kv2850  

5.995,-

8.495,-

På lager 1
KJØP
-29%
Art.nr: 34703T1
Copied
Nyt kraftig pickup-ytelse I realistisk skala 1/10! Med robuste dekk og understell for å håndtere ulendt terreng og et stort lasteplan bak, er pickuper etterspurt i hele Nord-Amerika, Sørøst-Asia, Afrika og Australia, og mange populære pickuper har blitt gjenskapt som R/C-modeller. Toyota utviklet Tacoma hovedsakelig for det nordamerikanske markedet og den har fortsatt å selge siden utgivelsen i 1995. Disse modellene er basert på 3. generasjon Tacoma som først fikk stor anerkjennelse i 2016 på grunn av sin aggressive stil og praktiske egenskaper. Toppen av serien Tacoma TRD Pro har blitt gjenskapt av Kyosho med et tøft 1/10-skala chassis i en Readyset-pakke. Kyoshos støpehåndverk gjengir TRD Pro-kroppen plettfritt i lett, men stiv polykarbonatharpiks med styrke for hard terrengkjøring. Basert på offroad KB10-chassiset passer den lange akselavstanden og den korte slitebanen til KB10L-chassiset perfekt til karosseriet. Det akseldrevne 4WD-systemet overfører rundt. pålitelig kraft til den børsteløse TORX10L-motoren for å nå topphastigheter på 75 km/t under av ESC (Electronic Speed Control) og et kompatibelt 3S (11.1V) lipo-batteri Denne praktiske Readyset-pakken inneholder moroa fra en ultraskala pickup på et dynamisk terrengchassis med en finish som i kvalitet ligner på premium-modeller som kun er skjermet. ●Readyset inkluderer R/C-system forhåndsinstallert på chassiset og en pistolgrepsender. ●Forhåndsmalt og montert "Toyota Tacoma TRD Pro" ultraskala karosseri fanger fullt ut formen til den originale lastebilen. ● Nydesignede kroppsfester skjuler kroppsstifter fra utsiden for å realisere en høyere skalafølelse. ●LED-lys (selges separat) kan festes til lysbøttene foran og bak. Skalafølelsen forsterkes ytterligere når 4 frontlykter og 2 baklykter (4 hvis tåkebaklys er installert) lyser fullt ut. Anbefalt: 4 lys foran, 2 baklykter (97054-4CR x 1, 97054-2B x 1) / Med tåkelys bak, 4 lys foran, 4 baklykter (97054-4B x 1, 97054-4CR x 1) ●Fulltids 4WD KB10L-chassis kan håndtere røffe veier så vel som på vei og flat skitt. ●Batteriholder kompatibel med 3S-batterier. Batteriet er festet med et belte som er lett å ta av og på. ●Inkluderer kraftig TORX 10L børsteløs motor og vanntett BRAINZ 10 + børsteløs ESC. ●3 differensialdesign for forbedret løpsstabilitet. Olje #10000 er forhåndsfylt i senterdiff og #5000 olje foran og bak. ●Full kulelager (22) utstyrt for optimal driveffektivitet og holdbarhet. ●Hver girenhet, mottaker er innelukket i en forseglet boks for å forhindre kompromisser fra sand og skitt under kjøring. ●Pistolgrep type Syncro KT-231P+ avsender inkludert muliggjør ulike innstillingsendringer. ●Batterilader og batteri for chassis pluss 4 x AA-batterier for sender må kjøpes separat. Lav og avlet form på polykarbonatkroppen er ulastelig gjenskapt med den unike TRD Pro frontgrillen og lett bøtter for å forbedre den 3-dimensjonale effekten. Holdbart 1,5 mm PC-hus. Karosserifester foran og bak fester karosseriet fra under chassiset (bildet viser fronten) slik at skalaens utseende ikke kompromitteres av synlige karosseristifter på utsiden av karosseriet. Basert på 1/10-skalaen Mad Wagon bush-basher offroad-chassis, har KB10L og utvidet akselavstand og forkortede fjæringsarmer med stabilitet til akseltypen 4WD. 4WD-system av akseltype med girkasse med senterdifferensial reduserer motorrotasjonen for optimal kraftoverføring til for- og bakhjul. Nydesignet langt aluminiumchassis gir pålitelig trekkraft selv på overflaten med lite grep. Oljedempere demper tilbakemeldinger fra veibanen for å stabilisere chassiset under kjøring. Forhåndsmonterte støtdempere er forhåndsfylte med olje og fjærhastighet (hardhet) er optimert for KB10L-chassiset. Sperrestenger på fjæring og styring gjør det enkelt å justere camber- og tåvinkelen. Forlengbare universalaksler i harpiks på de nedre opphengsarmene er utskiftbare mellom foran og bak for deler og vedlikeholdseffektivitet. Nylig vedtatt senterdifferensial i KB10L-chassiset optimerer kraftfordelingen til for- og bakhjuls hjørner for jevn svingytelse. IF245 cylindrisk stålhjul for 1/8-skala buggy Inferno NEO-serien kan installeres som en valgfri del.(Et BRG005-lager kreves separat.) Utstyrt med sintrede metall 4-fasede differensialgir foran og bak med kapasitet til å håndtere høyeffekter børsteløse motorer. IS117 hardt vinkelgir for 1/8-modellen Inferno NEO ST 3.0 kan installeres som en valgfri del.(BRG005-lager kreves separat.) Nydesignede hjul og dekk viser overlegent grep, både på og terreng. Dekkmønster og hjuldesign gjenskaper den faktiske kjøretøystilen for en full følelse av skala. Nødvendig for drift ● AA-batterier x 4 for sender ●Batteri for kjøring (2-3S LiPo batteri *Installerbart batteri størrelse 143x47x30mm) ●Lader for LiPo-batteri   English text:   Enjoy powerful pickup truck performance In realistic 1/10 scale! With rugged tires and undercarriage to handle rough terrain and a large rear cargo bed, pickup trucks are in high demand throughout North America, Southeast Asia, Africa, and Australia and many popular pickup trucks have been recreated as R/C models. Toyota developed the Tacoma mainly for the North American market and it has continued to sell well since its release in 1995. This model is based on the 3rd generation Tacoma which first appeared to much acclaim in 2016 due to its aggressive styling and practicality. The top of the range Tacoma TRD Pro has been recreated by Kyosho with a tough 1/10 scale chassis in a Readyset package. Kyosho’s molding craftmanship immaculately reproduces the TRD Pro body in lightweight but rigid polycarbonate resin with the strength for hard off-road driving. Based on the off-road KB10 chassis, the long wheelbase and short tread of the KB10L chassis matches the body perfectly. The shaft-driven 4WD system reliably transfers the brute power of the TORX10L brushless motor to reach top speeds of about 75km/h under the management of the ESC (Electronic Speed Control) and a compatible 3S (11.1V) lipo battery. This convenient Readyset package contains the fun of an ultra-scale pickup truck on a dynamic off-road chassis with a finish similar in quality to premium display-only models. ●Readyset includes R/C system pre-installed on the chassis and a pistol-grip transmitter. ●Pre-painted and assembled "Toyota Tacoma TRD Pro" ultra-scale body fully captures the form of the original truck. ●Newly designed body mounts conceal body pins from the outside to realize a higher sense of scale. ●LED lights (sold separately) can be attached to the front and rear light buckets. The scale feeling is further enhanced when 4 front lights and 2 rear lights (4 if rear fog lights installed) are fully lit. Recommended: Front 4 lights, Rear 2 lights (97054-4CR x 1, 97054-2B x 1) / With rear fog lights, Front 4 lights, Rear 4 lights (97054-4B x 1, 97054-4CR x 1) ●Full-time 4WD KB10L chassis can handle rough roads as well as on-road and flat dirt. ●Battery holder compatible with 3S size batteries. The battery is fixed with a belt that is easy to take off and on. ●Includes powerful TORX 10L brushless motor and waterproof BRAINZ 10 + brushless ESC. ●3 differential design for enhanced running stability. #10000 oil is pre-filled in the center diff and #5000 oil in the front and rear diffs. ●Full ball bearings (22) equipped for optimal drive efficiency and durability. ●Each gear unit, receiver are enclosed in a sealed box to prevent compromise from sand and dirt while driving. ●Pistol grip type Syncro KT-231P+ transmitter included allows various setting changes. ●Battery charger and battery for chassis plus 4 x AA batteries for transmitter must be purchased separately. Low & wide shape of the polycarbonate body has been immaculately recreated with the unique TRD Pro front grill and light buckets to enhance the 3-dimensional effect. Dunable 1.5mm PC body. Body mounts on front and rear secure the body from under the chassis (photo shows front) so scale appearance is not compromised by exposed body pins on the outside of the body. Based on the 1/10 scale Mad Wagon bush-basher off-road chassis, the KB10L has an extended wheelbase and shortened suspension arms with the stability of the shaft-type 4WD. Shaft-type 4WD system incorporating gearbox with center differential reduces motor rotation for optimal power transfer to front and rear wheels. Newly designed long aluminum chassis produces reliable traction even on low-grip surfaces. Oil shocks reliably attenuate feedback from the road surface to stabilize the chassis while driving. Pre-mounted shocks are pre-filled with oil and spring rate (hardness) has been optimized for the KB10L chassis. Turnbuckle rods on suspension and steering make it easy to adjust the camber and toe angle. Extendable resin universal shafts on the lower suspension arms are interchangeable between front and rear for parts and maintenance efficiency. Newly adopted center differential in the KB10L chassis optimizes power distribution to front and rear wheels through corners for smooth turning performance. IF245 steel spur gear for the 1/8 scale buggy Inferno NEO series can be installed as an optional part.(One BRG005 bearing is required separately.) Equipped with sintered metal 4-bevel differential gears on the front and rear with the capacity to handle high-power brushless motors. IS117 hard bevel gear for the 1/8 model Inferno NEO ST 3.0 can be installed as an optional part.(BRG005 bearing is required separately.) Newly designed wheels and tires demonstrate superior grip, both on and off-road. Tire pattern and wheel design replicate the actual vehicle style for a full sense of scale.

5.995,-

8.495,-

På lager 2
KJØP
-29%
Art.nr: 34363T2B
Copied
Realistic 2WD truck delivers the optimal combination of style and performance for the perfect introduction to R/C trucking. The OUTLAW RAMPAGE PRO readyset with a realistic roll cage adds more scale-oriented to the new concept full-scale 2WD truck and improving driving performance. The mechanism based on the actual truck gives a new driving feeling and brings more fun to drive R/C cars than ever. With a new chassis designed from the ground up, the underbody features double wishbone suspension on the front with a link system suspension on the rear in combination with the long stroke of high volume aerating oil shocks to deliver a standard of performance worthy of a 2WD trophy truck. Heavy-duty drive system realizes high durability and reliability and is designed to handle high loads with its 32-pitch module counter gear and diff gear and slipper clutch to manage sudden load changes from jump landings etc. With a power center combination consisting of the newly developed G15 brushed motor and large capacity Vortex WP Brush ESC 45A, the dynamic performance of the OUTLAW RAMPAGE is matched by its stunning 1970-80s trophy truck style with pre-cut and painted body with decals applied. Whether its the rough road or no road at all, the OUTLAW RAMPAGE puts the ultimate trucking experience in your hands. ● High strength and easy maintenance of the bathtub type chassis combines with a reinforced frame and dustproof monocoque radio box for high durability in hard driving. ● Equipped with underbody worthy of the 2WD trophy truck motif. Solid rear axle differential with link system delivers smooth suspension movement and traction for superior performance. ● Two mounting positions (on chassis) for rear suspension links allow setup to suit different driving conditions. ● Long suspension arms on the front double wishbone suspension deliver high traction and stability. Reflects real car mechanics, just as the rear does. ●Large capacity plastic aeration shocks maintain long suspension stroke in combination with the front and rear suspension systems. ● Omnipotent tires feature original tread pattern to deliver performance and style that matches the appearance of the scale body. Tires are fixed to the 3-piece wheel structure with screws so no gluing is required. ● Original truck body is designed in the image of a 1970s trophy truck. Chrome grill is available as optional parts (No. OLB051-01SM). ● Thicker and larger 32-pitch module counter gear and diff gear inside gearbox provide added strength. Spur gear is 48-pitch. ● Easy battery installation is possible with the lever lock battery holder. Radio plate with connector holder allows connection or disconnection with one hand.   Technical datas ● Length 561mm (with body) ● Width 262mm (with body) ● Height 231mm (with body) ● Wheelbase 335mm ● Tread (F/R) 204mm/204mm ● Tires (F/R interchangeable) φ108×38mm ● Gear Ratio 12.65 : 1 ● Motor 15 turn 540 type (G15 motor) ● Weight 2,400g approx.   Ready Set Contents ● Pre-assembled chassis installed with R/C unit ● Factory finished body with coloring and painted ● Syncro KT-231P+ transmitter ● TEAM ORION VORTEX WP Brush 45A ESC ● G15 brushed motor ● 7.2V-1800 Ni-MH battery ● AC Charger ● Hex wrench ● Cross wrench   Required for Operation 4 x AA-size batteries for transmitter

3.495,-

4.895,-

På lager 1
KJØP
-29%
Art.nr: 34363T1B
Copied
Realistic 2WD truck delivers the optimal combination of style and performance for the perfect introduction to R/C trucking. The OUTLAW RAMPAGE PRO readyset with a realistic roll cage adds more scale-oriented to the new concept full-scale 2WD truck and improving driving performance. The mechanism based on the actual truck gives a new driving feeling and brings more fun to drive R/C cars than ever. With a new chassis designed from the ground up, the underbody features double wishbone suspension on the front with a link system suspension on the rear in combination with the long stroke of high volume aerating oil shocks to deliver a standard of performance worthy of a 2WD trophy truck. Heavy-duty drive system realizes high durability and reliability and is designed to handle high loads with its 32-pitch module counter gear and diff gear and slipper clutch to manage sudden load changes from jump landings etc. With a power center combination consisting of the newly developed ‘G15’ brushed motor and large capacity Vortex WP Brush ESC 45A, the dynamic performance of the OUTLAW RAMPAGE is matched by its stunning 1970-80’s trophy truck style with pre-cut and painted body with decals applied. Whether it’s the rough road or no road at all, the OUTLAW RAMPAGE puts the ultimate trucking experience in your hands. ● High strength and easy maintenance of the bathtub type chassis combines with a reinforced frame and dustproof monocoque radio box for high durability in hard driving. ● Equipped with underbody worthy of the 2WD trophy truck motif. Solid rear axle differential with link system delivers smooth suspension movement and traction for superior performance. ● Two mounting positions (on chassis) for rear suspension links allow setup to suit different driving conditions. ● Long suspension arms on the front double wishbone suspension deliver high traction and stability. Reflects real car mechanics, just as the rear does. ●Large capacity plastic aeration shocks maintain long suspension stroke in combination with the front and rear suspension systems. ● Omnipotent tires feature original tread pattern to deliver performance and style that matches the appearance of the scale body. Tires are fixed to the 3-piece wheel structure with screws so no gluing is required. ● Original truck body is designed in the image of a 1970’s trophy truck. Chrome grill is available as optional parts (No. OLB051-01SM). ● Thicker and larger 32-pitch module counter gear and diff gear inside gearbox provide added strength. Spur gear is 48-pitch. ● Easy battery installation is possible with the lever lock battery holder. Radio plate with connector holder allows connection or disconnection with one hand.   Technical datas ● Length 561mm (with body) ● Width 262mm (with body) ● Height 231mm (with body) ● Wheelbase 335mm ● Tread (F/R) 204mm/204mm ● Tires (F/R interchangeable) φ108×38mm ● Gear Ratio 12.65 : 1 ● Motor 15 turn 540 type (G15 motor) ● Weight 2,400g approx.   Ready Set Contents ● Pre-assembled chassis installed with R/C unit ● Factory finished body with coloring and painted ● Syncro KT-231P+ transmitter ● TEAM ORION VORTEX WP Brush 45A ESC ● G15 brushed motor ● 7.2V-1800 Ni-MH battery ● AC Charger ● Hex wrench ● Cross wrench   Required for Operation 4 x AA-size batteries for transmitter

3.495,-

4.895,-

På lager 1
KJØP
-29%
Art.nr: 34412T2-BC
Copied
COMBO Kyosho MadVan T2 Readyset - Batt 2200 / Chargeur 1A Unique visuals of this American full-size van deliver excellent backroad driving performance Designed in the image of an American full-size van, Kyosho’s fun MAD VAN model combines retro body styling with a light and sporty chassis for pure R/C enjoyment. The simple design of the FZ02L-BT chassis uses fewer parts for easy maintenance and delivers strength and rigidity through front & rear stiffeners with reinforced ribbing and optimized material formulation on critical parts. In addition, the near symmetrical design and optimal front-rear suspension balance works in combination with the power source to produce excellent control and maneuverability for this type of model. Slipper clutch, front and rear differentials, oil shocks and full ball bearing specifications provide performance efficiency to compliment its high durability and impact-resistance. Soft compound, wide large-diameter tires with inner sponges feature rounded shoulders to produce secure grip, not only off-road, but on sealed surfaces too, so this van can be enjoyed just about anywhere! As the MAD VAN is a fully pre-assembled Readyset, only 4 x AA batteries for the transmitter, battery for the chassis, and a battery charger are required for the fun to begin. Whether going off-road or on-road, the MAD VAN produces dynamic performance to be enjoyed with its own unique style.   *The body is designed in the image of the American full size of the 1970s and 1980s, and the body color is metallic purple, which is still popular in the United States. *Includes decals that allow you to change the front grille / coloring and a separate roof spoiler made of polycarbonate that enhances driving performance, allowing customers to customize it to their liking. *The main chassis uses a lightweight, highly rigid glass-reinforced 66 nylon resin bathtub model.. *66 nylon is used for the suspension arms. Achieves a good balance between flexibility to absorb impact and rigidity around the tires. *Equipped with bevel gear type differential gears on the front and rear. Ensuring smooth turning when cornering. *Full ball bearing specifications minimize drive loss. *Comes with the new powerful 550 size 14T brushed motor(G14L). The long can with Steel ring around the motor case and internal cooling fan provides efficient torque and high speeds. *The front and rear suspensions are equipped with a 12mm diameter big bore oil damper. Achieves stable driving by absorbing the impact from the road surface during off-road driving. *Ball connect type kingpins are used on the front knuckle arm up and lower. The caster angle can be easily changed in 3 steps by moving the front upper suspension arm position back and forth with a spacer. *The front and rear knuckle arms and suspension arms are shared on the left and right. Increase compatibility of spare parts. *Since the motor mount has mounting holes according to the pinion gear, troublesome backlash adjustment is unnecessary. Supports from 29T to 37T. *ESC adopts waterproof 60A "KA060-91W" with reverse. It is also possible to switch between NIMH and LiPo batteries. (Factory default setting to LiPo mode) *A 20T pinion gear and a 76T spur gear are used for the primary acceleration. Demonstrates torque corresponding to large diameter tires. Equipped with a slipper clutch as standard to protect the gear from any impact. *A soft compound is used for large-diameter monster truck tires and equipped with an inner sponge. Provides good grip both on and off. *Uses hex screws in each part. Reliable tightening torque can be applied, and maintenance is possible with even fewer tools. Simple design of the low C of G FZ02L-BT chassis features a covered speed controller and receiver. The one-piece gearbox on the main chassis optimizes torsional rigidity and is made from shock-resistant lightweight nylon. Key components deliver structural strength to realize a simple upper deckless design. Reduced number of parts and consistency in size and type of screws means a 2.0mm hex wrench can be used for nearly all flathead screws. This allows easier assembly and disassembly for maintenance. Front suspension features optimized bump steer and scrub radius combined with reliable ball-connect steering knuckles. Front-rear and left-right interchangeable hub carriers improve parts efficiency and maintenance. Oil shocks are equipped as standard and deliver stable performance in all conditions. Optimal front-rear geometrical balance realizes light handling and control stability. Equipped with long 550 size 14-turn brushed G14L motor that generates enough torque power for wheelies when the battery is fully charged so the fun of dynamic big-tire performance can be enjoyed to the full! 76T spur gear and 20T pinion gear are designed for optimal big-tire performance. Wide range of gear ratios can be used with pinion gears from 20T~29T to suit various motors. In addition, backlash adjustment is made easy by direct installation of the motor according to the number of pinion gear teeth. Includes large capacity KYOSHO SPEED HOUSE (KA060-91W) 60A speed controller with super plug (Deans) connector. Features three control modes: FWD/Brake/REV (default setting), FWD/Brake, and FWD/REV. Compatible with Li-Po battery (for safety, setting at time of shipment is Li-Po mode). Angular shape of the molded polycarbonate body is designed in the image of an American full-size van style of the 1970-1980s. Large-diameter wide tires compliment the body design and deliver strong performance with the polycarbonate roof spoiler.Extra decal sheet included to customize body. Soft compound large-diameter wide tires deliver excellent grip on a wide range of surfaces, from paved surfaces such as parking lots, to sand, dirt and even grass.

2.795,-

3.995,-

På lager 1
KJØP
-30%
Art.nr: LOS03030T2
Copied
Losi 1/10 Hammer Rey U4 4WD Rock Racer Brushless RTR with Smart and AVC, Green Bred for off-road excellence, the Losi® Hammer Rey® is a SMART, RTR Rock Racer with AVC®. It's ideal for victory-minded enthusiasts looking for a superior RC experience with the inclusion of AVC, Spektrum™ Smart, and incredible scale details. Key Features REALISTIC DETAILS: 1 TO 1 SCALE LOOKS AND PERFORMANCE POWERFUL: SPEKTRUM™ 3150Kv BRUSHLESS POWER SYSTEM UNPARALLELED TECHNOLOGY: SMART AND AVC® In The Box (1) 1/10 Hammer Rey U4 4WD Rock Racer (1) Spektrum™ DX3™ Radio System (1) Spektrum Firma® 130 Amp Brushless Smart ESC (installed) (1) Spektrum Firma 4-Pole 3150Kv Brushless Motor (installed) (1) Spektrum™ S614S Metal Gear Servo (installed) (1) SR6200A DSMR 6-Channel AVC Surface Receiver (installed) (1) Product Instruction Manual (4) AA Batteries Needed to Complete (1) 2-3S LiPo Battery with EC5™ or IC5™ connector (1) Compatible Battery Charger Features Officially Licensed Casey Currie's U4 Racer Officially Licensed KMC Machete wheels and Nitto Trail Grappler M/T tires Spektrum SMART 130A ESC 3150Kv Brushless Power System Spektrum™ DX3™ Radio System Updated Steering System Updated Rear Axle Housing Independent Front Suspension with a Solid Rear Axle Waterproof Electronics Preset Motorplate LED Light Bars and Headlights Coil-over Oil-Filled Shocks Spektrum™ S614S Metal Gear Servo Sealed Metal-Gear Transmission and Diffs Rear-Loading Battery Longer Wheelbase Spektrum™ AVC® technology BRED FOR VICTORY The Losi® Hammer Rey® is a SMART, Ready-to-Run Rock Racer with AVC®. It is officially licensed and based off Casey Currie's U4 Racer. It's powered with a Spektrum™ 3150Kv brushless motor and managed by the Smart 130A ESC, 6-channel DSMR AVC/telemetry receiver, and the new DX3 transmitter that provides Spektrum Smart feedback including live battery voltage. Along with the officially licensed design, the Hammer Rey includes KMC wheels, Nitto tires, and additional details such as new shock reservoirs, fire extinguishers, and new light bars. It comes equipped with a solid rear axle, independent front suspension, and oil-filled shocks, so you can tear across all types of rocky off-road terrain. And you'll do so with the full-throttle freedom that only AVC® technology can provide. The Hammer Rey is ideal for victory-minded off-road enthusiasts looking for the top-of-the-line RC experience with the inclusion of AVC and the three-position limiting switch. With the Hammer Rey, Losi continues to push the limits when it comes to scale details, performance and officially licensed products.   Officially Licensed U4 Racer Officially licensed and based off Casey Currie's U4 Racer. It features authentic scale details to the Hammer Rey. These will have racers doing double takes as they take on all corners. Officially Licensed Wheels and Tires The Hammer Rey has the look and feel of its real-world counterparts in ways you never imagined with KMC Machete wheels and Nitto Trail Grappler M/T tires. Spektrum™ SMART 3150Kv Brushless Power System The Hamer Rey comes equipped with a Spektrum™ 3150Kv Brushless motor, a Spektrum™ Smart 130A Brushless ESC, and a Spektrum™ SR6200A DSMR 6-Channel AVC/telemetry receiver providing Spektrum™ Smart feedback including live battery voltage. This potent combination can handle up to 3S LiPo batteries (sold separately) and will allow you to hurtle across the landscape at speeds of up to 40 mph. Spektrum™ DX3™ Radio System The Spektrum™ DX3™ radio system offers advanced features like AVC® technology, a 3-position throttle limiting switch, and travel adjust. Scale Details Secondary shock with faux cooling reservoirs, fire extinguishers, Magnaflow exhaust system, upper LED light bar, lower LED light bar, LED headlights, fuel cell, faux sway bar, brake calipers/rotors, side mirrors, and more. Updated Steering System The steering servo mount and steering bell cranks have been re-designed for added durability. Updated Rear Axle Housing The Hammer Rey rear suspension allows it to soak up massive whoops and bumps with the same realistic handling and movement of a full-scale U4 off-road racer. The rear axle housing includes an updated third member that uses larger diameter pinion bearings as well as an updated upper rear link mount for added durability. Independent Front Suspension The front, independent suspension has been carefully engineered letting the Hammer Rey rip across the terrain with confidence. By having fully independent suspension, it allows each side to react accordingly providing more control and more precise steering and handling. Waterproof Electronics The Hammer Rey is loaded with waterproof electronics including the receiver, servo and ESC. Everything is sealed against the elements allowing you to splash in the rain, spin in the mud and make tracks in the snow. It's full-throttle freedom to run anytime, rain or shine. Preset Motorplate Easier and precise gear mesh settings with different pinion choices. LED Light Bars and Headlights The fun doesn't stop even when the sun goes down with the Hammer Rey. A brilliant LED lights on the integrated light bars cast more than enough illumination for running at night. Plus, the body-mounted LEDs place only a small demand on the battery allowing you to stay out all night! Coil-over Oil-Filled Shocks The long-travel shocks do a fantastic job of soaking up the energy from big bumps and jumps. They also feature threaded shock bodies with adjustment collars so you can fine tune the pre-load settings of the coil-over springs. Spektrum™ S614S Metal Gear Servo Improved high-torque servo provides robust steering. Sealed Metal-Gear Transmission and Diffs The single-speed transmission, as well as the front and center diffs, are sealed against the elements and engineered to handle the abuse of a high-output brushless motor and punishing terrain. MOD 1 gears further increase the durability of this desert beast. The adjustability of three diffs allows drivers to set their Hammer Rey to handle any track conditions. Rear-Loading Battery The innovative rear-loading battery feature makes it possible to change the battery quickly, easily and without the inconvenience of removing the body. Longer Wheelbase The longest wheelbase on the Rey platform for increased performance and added stability at speed. The Full-Throttle Freedom of AVC® Technology The receiver's built-in AVC® (Active Vehicle Control®) traction control system works behind the scenes, making hundreds of throttle and steering adjustments per second, so more of the motor's power is translated into ballistic speed and acceleration instead of just flying dirt. The patent pending AVC system adds a level of performance that simply cannot be found with any vehicle from any manufacturer other than Horizon Hobby. Like traction control in your full-scale vehicle, you can activate or deactivate the system on the fly and adjust the level of stability based on driving conditions. Any RC vehicle can go fast and with AVC you can go faster while maintaining optimum stability in all driving conditions. OFFICIALLY LICENSED Every weekend off-road racing driver, Casey Currie's feet are touching dirt and the gas pedal. His career has taken him all over the world with a highlight being his threepeat at the Baja 1000 in 2017, 2018, and 2019. Full-scale U4 race trucks are a unique breed. Not only are they expected to cruise at 90MPH across the desert, but also have the torque and driveline strength to get over rock formations that look impossible to navigate. One reason Casey Currie and his U4 race truck works so well with the Rey platform was the featured independent suspension up front and solid axle in the rear. Of course with Losi, drivers get as much detail as possible while preserving the performance and durability the Rey platform is known for in the RC racing community. The combination is a one-way ticket to victory after victory, bred for the desert and ready to impress. Product Specifications Charger Sold Separately Differential Bevel gear, sealed Receiver Included Shock Type Coil-over, oil-filled Battery Sold Separately Motor Size 3150 Kv Product Length 26.45" (672 mm) Spur Gear 43T Suspension Front independent, Rear 4-link Vehicle Type Rock Racer Water-Resistant Yes Motor Type Brushless - Sensorless Rear Track 12.37 Speed Control Included Wheelbase 17.22" (437 mm) Ball Bearings Yes Chassis 3mm plate, 6061-T6 aluminum Completion Level Ready-To-Run Approximate Assembly Time No assembly required Body Screened polycarbonate Brakes Integrated with ESC Pinion 11T Scale 1/10 Front Track 12.37 Product Width 12.37" (314 mm) Radio Included Technology AVC and SMART Drivetrain 4WD Drive Type Forward/Brake/Reverse Product Height 11.11" (282 mm) Top Speed 40+ Wheel Hex Size 12mm Power Type Electric Gear Pitch 1.0 Mod Servos Included

5.295,-

7.995,-

På lager 2
KJØP
-34%
Art.nr: MZP159OR
Copied
Body Overview: Kyosho Mini-Z MR-04N-RM Porsche 911 GT3 RS Body. This is a ready to install detailed body option for the MR-04N-RM platform chassis. This body is equally suited to use as a display model, or to give your existing model a face lift.    Includes: (1) Mini-Z MR-04N-RMW-LM Porsche 911 GT3 RS Body (1) Display Stand Box *Note: This product is a spare body set and cannot be run.

499,-

899,-

På lager 15
KJØP
-44%
Art.nr: 25207
Copied
Tamiya lanserer her sin 1/35 Leopard 2 A6 Tank “Ukraine” med støpte deler og tilbehør fra 35271 1/35 Leopard 2 A6 Tank Main Battle Tank, pluss nye dekaler som viser Ukrainas hærflagg. Den har utfyllende malingsveiledning og ny emballasje. I januar 2023 kunngjorde den tyske regjeringen at den ville sende 14 stk Leopard 2 A6-stridsvogner til Ukraina, og senere legge til ytterligere fire. Så fra Mars 2023 var det planlagt å sende totalt 18 stk av den stritsvognen. Dekaler i dette settet viser også et hvitt kors, et symbol som historisk ble brukt i Ukraina av grupper som kosakker. Om modellen • Dette er et plastsettet i skala 1/35 Lengde: 314mm. • Leopard 2 A6-tanken – med langløp 120 mm kanon, kileformede front- og sidepanserplater – er autentisk laget. • Leveres med nye dekaler som viser det ukrainske flagget og hvitt kors, komplett maleguide og ny emballasje. • Gjennomsiktige deler gjengir front- og baklys. • Vær oppmerksom på at enkelte komponenter som roterende lys, veiskilt og torsofigurer ikke er nødvendige for dette settet. • Vær også oppmerksom på at dekaler fra vare 35271 ikke er inkludert   Fra produsenten: Length: 314mm. About the Leopard The Leopard 2 was developed in the 1970s in the former West Germany, and by the time of its more modern A6 variant had received multiple upgrades to boost its offensive and defensive capabilities. While the wedge-shaped additional turret armor and the commander’s panoramic sight were carryovers from the A5 variant, its newer L/55 120mm smoothbore gun was a meter longer than previously for significantly improved muzzle speed and penetration. A6 tanks were deployed from 2001, and were even fielded by other nations such as Greece and Canada, with their own modifications. In January 2023, the German government announced that it would send Leopard 2 A6 tanks to Ukrainian forces.   About the Model ★This is a 1/35 scale plastic model assembly kit. Length: 314mm, width: 107mm. ★The refined Leopard 2 A6 form with 120mm smoothbore gun is recreated in style. ★Distinctive turret front and side additional armor is authentically depicted. ★Clear parts are included to recreate headlights and taillights. ★Includes belt type depictions of tracks. ★Decals in this kit include Ukranian flags and the white cross, a symbol historically used in Ukraine as a symbol of victory.        

359,-

649,-

På lager 14
KJØP
-45%
Art.nr: TRX 2844R
Copied
Traxxas 2844R - 2S Hardcase 5200mAh LiPo Battery iD™ 5200mAh 7.4v 2-cell 35C LiPo Battery Designed for spec-class racing, this 7.4-volt 2-cell LiPo battery features a tough outer hard case to protect against crash damage and meets sanction race requiements. The enhanced 35C discharge rate provides extra punch for brushless systems to bring home the win. Traxxas Certified iD®-Equipped LiPo batteries provide the punch and on-demand power to reach the top speeds that Traxxas models are built to deliver. Traxxas’ exclusive iD battery system is the easier and safer way to charge your Traxxas batteries. Only Traxxas gives you more of what you want most: simple installation, a great price, and the most speed and run time available. Specs: Type: LiPo Capacity: 5200mAh Voltage: 7.4V C Rating: 35 Length: 139mm Height: 25mm Width: 47mm Weight: 277g Type of Battery: Li-Po Length: 139 mm Height: 25 mm Weight: 277 g Width: 47 mm Capacity: 5200 mAh Number of Cells: 2 Voltage: 7,4 V C-Rating: 35 C Power Connector: Traxxas iD Balancing Connector: Traxxas iD Special Functions: Hardcase

695,-

995,-

På lager 17
KJØP
-30%
Art.nr: 2791-00
Copied
Crestline 1.9" Aluminum Composite Internal Bead-Loc Wheel for Rock Crawlers Front or Rear This is a pair of Crestline 1.9" Aluminum Composite Internal Bead-Loc Wheels. Pro-Line is proud to introduce the all-new Crestline 1.9" Aluminum Internal Bead-Loc Wheels! These new Crestline wheels are designed to not only look scale with the stepped 6 spoke design, but to be super easy to use by only requiring 6 screws per wheel for mounting tires. The face of the Crestline has been CNC machined to exacting tolerances and precision finishes that are second to none! These look just like real wheels! The unique 3-piece wheel design bolts together in the back and locks on to Pro-Line's incredible list of 1.9" Crawling Tires the same way as Pro-Line's Impulse 1.9" plastic wheel. The overall wheel width and wheel offset are the same as Pro-Line's Impulse 1.9" plastic Wheels, so you know they will fit your truck and look good doing it. Get your very own set of Pro-Line Crestline 1.9" Aluminum Composite Wheels today!   Features The Next Level of Scale Realism All-new Crestline Wheel Style CNC Machined-Aluminum Wheel Face 12mm Hex Pocket Milled into the Wheel Shiny Raw Aluminum Clear Anodized Finish on Wheel Face 3-piece Wheel Design fits Pro-Line's 1.9" Crawling Tires Wheel Center and Wheel Back Made from high-strength, durable DuPont Nylon     Includes Crestline 1.9" Machined-Aluminum Wheel Face (2 pcs) Black Plastic Wheel Back (2 pcs) Black Plastic Internal Bead-Loc Ring (2 pcs) M2.5 x 8 SHCS (12 pcs) M2.5 x 3 SHCS (12 pcs)     Fits 1:10 Rock Crawlers with 12mm Hex

549,-

929,-

På lager 14
KJØP
-41%
Art.nr: 2790-00
Copied
Impulse 1.9" Aluminum Composite Internal Bead-Loc Wheel for Rock Crawlers Front or Rear This is a pair of Impulse 1.9" Aluminum Composite Internal Bead-Loc Wheels. Pro-Line is proud to introduce our new Impulse 1.9" Aluminum Internal Bead-Loc Wheels! These new Impulse wheels are designed to not only look scale with the split 6 spoke design, but to be super easy to use by only requiring 6 screws per wheel for mounting tires. The face of the Impulse has been CNC machined to exacting tolerances and precision finishes that are second to none! These look just like real wheels! The unique 3-piece wheel design bolts together in the back and locks on to Pro-Line's incredible list of 1.9" Crawling Tires the same way as Pro-Line's Impulse 1.9" plastic wheel. The overall wheel width and wheel offset are the same as Pro-Line's Impulse 1.9" plastic Wheels, so you know they will fit your truck and look good doing it. Get your very own set of Pro-Line Impulse 1.9" Aluminum Composite Wheels today!   Features The Next Level of Scale Realism Popular Impulse Wheel Style CNC Machined-Aluminum Wheel Face 12mm Hex Pocket Milled into the Wheel Shiny Raw Aluminum Clear Anodized Finish on Wheel Face 3-piece Wheel Design fits Pro-Line's 1.9" Crawling Tires Wheel Center and Wheel Back Made from high-strength, durable DuPont Nylon     Includes Impulse 1.9" Machined-Aluminum Wheel Face (2 pcs) Black Plastic Wheel Back (2 pcs) Black Plastic Internal Bead-Loc Ring (2 pcs) M2.5 x 8 SHCS (12 pcs) M2.5 x 3 SHCS (12 pcs)     Fits 1:10 Rock Crawlers with 12mm Hex

599,-

999,-

På lager 15
KJØP
-40%
Art.nr: 10171-14
Copied
Pro-Line Class-0 BFGoodrich Krawler T/A KX 1.9" (3.85" OD) Rock Crawling Truck Tires G8 Pro-Line is proud to announce the fully licensed Krawler T/A® KX 1.9" tires in the new 3.85" OD size continuing our successful partnership with the leading full-size Off-Road tire manufacturer - BFGoodrich®! This collaboration started with the introduction of the full-race BFGoodrich® Baja T/A® KR2 tires and continued with the extremely popular BFGoodrich® All-Terrain KO2. The Krawler T/A® KX (KX is for Key feature: eXtreme traction) is BFGoodrich's Off-Road Maximum Traction tire for off-road enthusiasts who participate in the extreme sport of rock crawling to challenge their crawling skills and the performance of their vehicles. This purpose-built rock crawling tire was developed through participation in competition as BFGoodrich® worked directly with full-size rock crawling enthusiasts. The all-new 3.85" OD size is Pro-Line's smallest 1.9" tire to date and provides incredible scale performance in a small package. The Krawler T/A® KX features an extra deep tread design with a tread pattern that combines deep, aggressive independent blocks with solid sidewall lugs. Pro-Line's re-creation of the Krawler T/A® KX comes in at 3.85" tall x 1.31" wide for the perfect balance of Ultra-Scale looks and performance! Features: Licensed BFGoodrich® Krawler T/A® KX Tire Design Blue & Red Label Editions - Made from Pro-Line's Legendary G8 & Super Soft Predator Compound Own the Same Tires That are Used on Many Full-Size Rock Crawling Rigs Exacting Scale Detail Down to the Tire Warnings and T/A® Sidewall Tread Logos 3.85" tall x 1.31" wide for the Perfect Balance of Scale Looks and Performance Soft Foam Inserts Included for Maximum Traction Made in the USA, since 1982 Included: BFGoodrich® Krawler T/A® KX 1.9" Tires (2 pcs) Soft White Foam Inserts (2 pcs) Fits: 1.9" Rock Crawling Front or Rear Wheels Specs: Height: 98mm Width: 33mm Specification: Outer Diameter: 98 mm Scale: 1/10 Size: 1,9 Inch Suit: Crawler Compound: G8 (Rock Terrain) Width: 33 mm

299,-

549,-

På lager 17
KJØP
-46%
Art.nr: 2797-03
Copied
Proline 1/10 Keystone Front/Rear 1.55" 12mm Rock Crawler Wheels (2) Black Key Features Popular Wheel Style Mimics Full-Size Steel Wheels Blacked Out Wheel Color 12mm Hex Wheel Molded-In Lug Nuts for a Scale Look Made in the USA, since 1982 In The Box (2) Black, Keystone 1.55" Wheels (1 Set) Mounting Hardware Wheel Features: Popular Wheel Style Mimics Full-Size Steel Wheels Blacked Out Wheel Color 12mm Hex Wheel 3-piece Plastic Wheel Design Fits Pro-Line and other 1.55" Crawling Tires Molded-In Lug Nuts for a Scale Look Wheel Made from High-Strength, Durable DuPont Nylon Mounting Hardware Included Made in the USA, since 1982 Overview: Pro-Line is proud to introduce our all-new Keystone 1.55" Black Plastic Internal Bead-Loc 12mm Wheels that are Proudly Made in the USA! These all-new Keystone wheels are designed to not only look scale but to be super easy to use by only requiring 5 screws per wheel for mounting tires. The unique 3-piece plastic wheel design bolts together in the back and locks on to Pro-Line's 1.55" Crawling Tires or any other 1.55" Crawling tire. The Keystone 1.55" wheel features 10 D-shaped holes and mimics the style of the popular steel wheels found on full-size trucks. This wheel has a 12mm hex molded in and is designed to fit all popular straight axle rock crawlers on the market. These Keystone wheels are destined to become the new standard in 1.55" crawler wheels. Please note: All tires & wheels are sold in pairs, unless otherwise noted. Fits: 1:10 Rock Crawlers with 12mm Hex and Straight Axles Product Specifications Manufacturer # 2797-03 Inner Tire / Outer Wheel Diameter 1.55 in Outer Diameter 1.55" (39 mm) Package Type Wheels Only Product Height 1.55" (39 mm) Product Width 0.97" (25 mm) Color Black Scale 1/10 Track Surface Rock Crawling Vehicle Type Rock Crawler Wheel Hex Size 12mm Wheel Position Front/Rear Wheel Type Keystone

259,-

439,-

På lager 16
KJØP
-41%
Art.nr: 2798-00
Copied
PROLINE 1/10 Slot Mag Aluminum Front/Rear 1.55" 12mm Rock Crawler Wheels (2) Pro-Line is proud to introduce our all-new Slot Mag 1.55" Aluminum Composite Internal Bead-Loc 12mm Wheels! These all-new Slot Mag wheels are designed to not only look super scale but also to be extremely easy to use by only requiring 5 screws per wheel for mounting tires. The unique 3-piece wheel design bolts together in the back and locks on to Pro-Line's 1.55" Crawling Tires or any other 1.55" Crawling tire. The Slot Mag 1.55" features a machined aluminum wheel face with 5 oval-shaped holes that mimic the style of the popular full-size Slot Mag wheels that have been around since the 1960s. This wheel has a 12mm hex machined into the back of the wheel face and is designed to fit all popular straight axle rock crawlers on the market. These Slot Mag wheels are destined to become the new standard in 1.55" crawler wheels. Features: Popular Wheel Style that Mimics Full-Size Slot Mag Wheels Machined Aluminum Wheel Face with 12mm Hex Machined in 3-piece Wheel Design fits Pro-Line and other 1.55" Crawling Tires Wheel Center and Wheel Back Made from High-Strength, Durable DuPont Nylon Mounting Hardware Included Fits: 1/10 Rock Crawlers with 12mm Hex and Straight Axles Included: (2) Slot Mag 1.55" Aluminum Wheels (1 Set) Mounting Hardware

539,-

899,-

På lager 16
KJØP
-40%
Art.nr: 58729
Copied
Tamiya 58729 Opel Kadett GT/E 1975 1/10 – MB-01 Byggesett inkl. ESC En legendarisk rallyklassiker fra 1970-tallet – nå som detaljert radiostyrt modell fra Tamiya! Tamiya Opel Kadett GT/E 1975 er et flott RC-byggesett i skala 1/10 som gjenskaper en av Opels mest ikoniske sports- og rallybiler. Med sitt klassiske todørs coupékarosseri, bakhjulsdrift og Tamiyas fleksible MB-01-chassis kombinerer denne modellen nostalgisk design med moderne RC-teknologi. Den originale Opel Kadett GT/E ble lansert i 1975 som en sportslig toppmodell med en kraftig 1,9-liters motor og forbedret hjuloppheng. Bilen ble raskt populær innen rallysporten, og i 1976 bidro Opel Kadett GT/E til at Opel sikret andreplassen i konstruktørmesterskapet i rally-VM. Tamiya har gjenskapt denne klassikeren med et detaljert karosseri i lett og slitesterk polykarbonat (Lexan), montert på det allsidige MB-01-chassiset. MB-01 – fleksibelt chassis med bakhjulsdrift Tamiya MB-01 er et kompakt og gjennomtenkt 2WD-chassis som gir mange muligheter for både kjøring og fremtidige ombygginger. På Opel Kadett GT/E er chassiset konfigurert med bakhjulsdrift, midtmontert motor bak og lang akselavstand på 239 mm, slik at oppsettet gjenspeiler drivlinjen til den originale bilen. En av de store fordelene med MB-01 er muligheten til å bygge chassiset med enten forhjulsdrift eller bakhjulsdrift. Det støtter også tre forskjellige akselavstander, noe som gjør det til en spennende plattform for videre utvikling og tilpasning. Chassiset har uavhengig hjuloppheng med doble bærearmer på alle fire hjul, og er konstruert med separate moduler som gjør både montering og vedlikehold enklere. Høydepunkter Skala 1/10 – detaljert modell av Opel Kadett GT/E fra 1975. Bakhjulsdrift (2WD) – klassisk kjørefølelse med motoren plassert foran bakakselen. Tamiya MB-01-chassis – fleksibel konstruksjon med flere muligheter for ombygging. Detaljert Lexan-karosseri – lett polykarbonatkarosseri som skal lakkeres. Uavhengig hjuloppheng – doble bærearmer foran og bak. 540 børstemotor inkludert – velprøvd motortype fra Tamiya. THW-1060 fartsregulator (ESC) inkludert – elektronisk hastighetsregulering. 60 mm dekk foran og bak – passer modellens klassiske proporsjoner. Byggesett – perfekt for deg som liker å bygge, tilpasse og vedlikeholde din egen RC-bil. Tekniske spesifikasjoner Egenskap Spesifikasjon Produsent Tamiya Varenummer 58729 Modell Opel Kadett GT/E 1975 Skala 1/10 Chassis MB-01 Drift 2WD – bakhjulsdrift Motorplassering Midtmontert bak (MR) Motor 540 børstemotor Fartsregulator THW-1060 ESC inkludert Lengde 417 mm Bredde 174 mm Høyde 138 mm Akselavstand 239 mm Dekkdiameter 60 mm foran og bak Karosseri Polykarbonat (Lexan) Hjuloppheng Uavhengig med doble bærearmer Støtdempere Friksjonsdempere Levering Byggesett – må monteres og lakkeres Dette trenger du i tillegg For å gjøre bilen komplett og kjøreklar trenger du: 2-kanals radiosender og mottaker Styreservo 7,2V NiMH- eller kompatibelt 7,4V LiPo-batteri Passende batterilader Tamiya PS-lakk til Lexan-karosseriet Kulelagersett hvis man ønsker.  Merk: Dette er et byggesett som må monteres og lakkeres før bruk. Motor og elektronisk fartsregulator følger med, men radioutstyr, servo, batteri, lader og lakk kjøpes separat. En klassiker for både RC-entusiaster og Opel-fans Tamiya Opel Kadett GT/E er et godt valg for deg som setter pris på klassiske rallybiler, realistiske detaljer og gleden ved å bygge din egen radiostyrte bil. MB-01-chassiset gir også gode muligheter for senere oppgraderinger, blant annet med kulelager og andre tilleggsdeler. Bygg din egen Opel Kadett GT/E og opplev en ekte rallyklassiker i radiostyrt utgave!

1.595,-

2.395,-

På lager 20
KJØP
-33%
Art.nr: 58583
Copied
Tamiya Egress 2013  1/10 4WD buggy-byggesett Byggesett – ikke kjøreklar. Tamiya Egress (2013) er nyutgaven av den akseldrevne konkurransebuggyen Tamiya utviklet med utgangspunkt i Avante. Den har chassis i karbonfiber og kuledifferensialer foran og bak, og den er fullt kulelagret fra fabrikk. Motor, fartsregulator (ESC), radioutstyr, servo, batteri og lader kjøpes separat. Produktbildet viser en ferdig bygget og lakkert modell. Karosseriet leveres ulakkert. Fra Avante til Egress Avante kom i 1988 som Tamiyas toppmodell blant 4WD-buggyene. Året etter etablerte Tamiya racingteamet TRF (Tamiya Racing Factory). Med erfaringene derfra ble Egress utviklet som en ren konkurranseversjon av Avante. Originalen hadde karbonfiberplater, kuledifferensialer, store oljedempere og lette titanskruer. Ifølge Tamiya konkurrerte Egress som den eneste akseldrevne bilen i en tid da beltedrevne biler dominerte. Nyutgaven kom i november 2013 med fornyet drivverk og hjuloppheng, og Tamiya har produsert den på nytt i 2024. Titanskruene fra originalen er ikke med. Chassis og drivverk Chassiset er en dobbeltdekkskonstruksjon med øvre og nedre plate i karbonfiber, og det er svært stivt. Motoren står på langs, og kraften går via kardanaksler til kuledifferensialer foran og bak. Akselavstanden er 15 mm lengre enn på Avante, for bedre stabilitet. Kuledifferensialene er nykonstruert for 2013-utgaven. De går jevnere, tåler mer og er enklere å vedlikeholde. Drivhjulet har et innebygd enveislager (torque splitter) som gir nøytral styring. Ved monteringen kan du i stedet velge låst senterdrift. Delene til begge løsningene følger med. Kardanakslene har samme oppbygning som i Tamiyas TRF-serie. Det gir effektiv kraftoverføring og bedre slitestyrke. Drivverket er fullt kulelagret, noe som reduserer friksjonen, og styringen har også kulelager. Du trenger derfor ikke kjøpe eget lagersett. Hjuloppheng og styring Alle fire hjul har uavhengige doble bærearmer, slik at hvert hjul kan bevege seg for seg over ujevnt underlag, og store oljedempere med aluminiumssylinder. Stabilisatorer foran og bak bidrar til å begrense krengning, og de fremre hjulspindlene er i maskinert aluminium. Styringen har kulelagrede styrearmer, en 2 mm tykk karbonfiberplate og tredelte styrestag, som gir lineær styrerespons. Slik er byggingen Du monterer selv chassis, differensialer, drivverk, hjuloppheng og støtdempere før bilen kompletteres med motor, elektronikk og radioutstyr. Monteringsmanualen har 50 byggetrinn fordelt på delposene A–D, og den er skrevet på japansk, engelsk, tysk og fransk. Du finner den under fanen «Manual». Fett, dempeolje og de nøklene du trenger mest, følger med. Karosseriet i polykarbonat lakkeres med Tamiya PS-lakk. Manualen bruker PS-5 svart og PS-41 lys sølv. Dekorark følger med. Byggesettet passer best for deg som har bygget RC-biler før. Tamiya anbefaler at barn og nybegynnere får hjelp av en erfaren modellbygger. Dette trenger du i tillegg Elektromotor av 540-type. Ifølge Tamiya fungerer også dagens børsteløse motorer svært godt. Elektronisk fartsregulator (ESC) tilpasset motoren Radiosett med minst 2 kanaler Styreservo i standardstørrelse (mini-servo passer ikke) Stavformet kjørebatteri av Tamiya-typen (firkantede batteripakker passer ikke) Lader til kjørebatteriet Batterier til senderen Tamiya PS-lakk til karosseriet Verktøy: stjerneskrujern (stort og lite), flatt skrujern, modellkniv, spisstang, avbitertang, saks, 2 mm håndbor og fil Sekundlim og gjengelås (gel) Tekniske spesifikasjoner Produsent Tamiya Varenummer 58583 Modell Egress (2013) Type Elektrisk 1/10 4WD offroad-buggy, byggesett Lengde / bredde / høyde 430 / 243 / 157 mm Akselavstand 275 mm Sporvidde foran og bak 200 mm Chassis Dobbeltdekk i karbonfiber Drift Akseldrevet 4WD, motor på langs Differensialer Kuledifferensialer foran og bak Senterdrift Enveislager (torque splitter) eller låst, velges ved montering Hjuloppheng Doble bærearmer på alle 4 hjul, stabilisatorer foran og bak Støtdempere 4 store oljedempere med aluminiumssylinder Styring 3-delte styrestag, kulelagrede styrearmer, 2 mm karbonplate Kulelager Fullt kulelagret Dekk (bredde/diameter) Foran 32/88 mm, bak 40/88 mm Pinjong 22T, følger med Karosseri Polykarbonat med underdeksel, ulakkert Motor og ESC Følger ikke med Dette følger med Byggesett med karbonfiberchassis, drivverk, hjuloppheng og styring Kuledifferensialer foran og bak, og deler til både enveislager og låst senterdrift Komplett sett med kulelager Fire store oljedempere med aluminiumssylinder og dempeolje (#400) Stabilisatorer foran og bak Pinjong 22T Felger og dekk med knastmønster Ulakkert karosseri og underdeksel i polykarbonat, og bakvinge Dekorark Fett til kuledifferensialene, keramisk fett og anti-wear-fett Kryssnøkkel, 1,5 mm unbrakonøkkel og fastnøkler Borrelåsbånd, dobbeltsidig tape, buntebånd og antennefeste Monteringsmanual Viktig: Dette er et byggesett, ikke en kjøreklar RTR-bil. Motor, fartsregulator, radioutstyr, servo, kjørebatteri, lader, senderbatterier og lakk følger ikke med. English product description Tamiya Egress (2013) 58583 – 1/10 Scale 4WD Off-Road Racing Buggy Kit Assembly kit – not ready-to-run. The Tamiya Egress (2013) is the re-release of the shaft-driven racing buggy that Tamiya developed from the Avante. It features a carbon-fiber chassis and ball differentials front and rear, and it is supplied with full ball bearings as standard equipment. Motor, electronic speed controller (ESC), radio equipment, steering servo, battery and charger are sold separately. The product photo shows a painted and assembled model. The body is supplied unpainted. From Avante to Egress – A Tamiya Racing Legacy When Tamiya introduced the Avante in 1988, it represented an important technological milestone in the development of RC off-road racing cars. The following year Tamiya founded the Tamiya Racing Factory (TRF), and the Egress was developed from the Avante as a dedicated racing machine, using the know-how gained in competition. The original Egress featured carbon-fiber chassis plates, ball differentials, high-capacity oil dampers and lightweight titanium screws. According to Tamiya, the Egress raced as the only shaft-driven car at a time when belt-driven cars dominated. The 2013 edition was first released in November 2013, and Tamiya produced it again in 2024. It preserves the distinctive appearance and fundamental engineering philosophy of the original while introducing improvements to several mechanical assemblies. Unlike the original version, the 2013 kit does not include titanium screws. Chassis and Drivetrain The chassis is constructed around upper and lower carbon-fiber plates in a double-deck configuration, giving it very high rigidity. A longitudinally mounted motor drives the shaft-driven four-wheel-drive transmission with ball differentials front and rear. The wheelbase is 15 mm longer than that of the Avante, for improved stability. The ball differentials have been redesigned for the 2013 edition. They run more smoothly, are more durable and are easier to maintain. A one-way bearing built into the drive gear acts as a torque splitter for neutral handling. Alternatively, a locked center drive can be selected during assembly. Parts for both options are included. The universal drive shafts share the design of those used in Tamiya's current TRF series parts, for efficient power transmission and improved resistance to wear. The drivetrain is supplied with full ball bearings as standard equipment, reducing friction throughout the drivetrain, and ball bearings are also incorporated into the steering. A separate ball bearing set is therefore not required. Suspension and Steering All four wheels are equipped with independent double-wishbone suspension, allowing each wheel to respond individually to changes in the terrain, and high-capacity oil dampers with aluminum cylinders. Front and rear stabilizer bars help reduce chassis roll, and the front uprights are machined from aluminum. The steering features ball-bearing-supported linkage arms, a 2 mm thick carbon-fiber plate and 3-piece steering tie rods for a linear steering response. Assembly The builder assembles the chassis, differentials, transmission, suspension and shock absorbers before installing the motor, electronic equipment and radio system. The instruction manual covers 50 assembly steps using parts bags A–D and is printed in Japanese, English, German and French. You will find it under the "Manual" tab. Greases, damper oil and the most frequently used wrenches are included. The polycarbonate body is painted with Tamiya PS paint. The manual specifies PS-5 Black and PS-41 Bright Silver. A decal sheet is included. The kit is best suited to builders with previous RC assembly experience. Tamiya recommends that children and inexperienced builders get help from an experienced modeler. Additional Items Required Type 540 electric motor. According to Tamiya, current brushless motors also deliver excellent performance. Electronic speed controller (ESC) compatible with the selected motor Radio system with at least 2 channels Standard-size steering servo (mini servos cannot be installed) Stick-type drive battery of the Tamiya battery pack type (square battery packs cannot be used) Charger for the drive battery Transmitter batteries Tamiya PS paint for the body Tools: Phillips screwdrivers (large and small), flat-blade screwdriver, modeling knife, long-nose pliers, side cutters, scissors, 2 mm pin vise and a file Instant cement and gel-type thread lock Technical Specifications Manufacturer Tamiya Item number 58583 Model Egress (2013) Type Electric 1/10 4WD off-road buggy, assembly kit Length / width / height 430 / 243 / 157 mm Wheelbase 275 mm Tread (front and rear) 200 mm Chassis Carbon-fiber double deck Drive Shaft-driven 4WD, longitudinal motor Differentials Ball differentials front and rear Center drive One-way bearing (torque splitter) or locked, selected during assembly Suspension 4-wheel double wishbone, stabilizers front and rear Dampers 4 high-capacity oil dampers with aluminum cylinders Steering 3-piece tie rods, ball-bearing-supported linkage arms, 2 mm carbon plate Bearings Full ball bearings Tires (width/diameter) Front 32/88 mm, rear 40/88 mm Pinion 22T, included Body Polycarbonate with undertray, unpainted Motor and ESC Not included Kit Contents Assembly kit with carbon-fiber chassis, drivetrain, suspension and steering components Front and rear ball differentials, plus parts for both the one-way bearing and the locked center drive Complete set of ball bearings Four high-capacity oil dampers with aluminum cylinders and damper oil (#400) Front and rear stabilizers 22T pinion gear Wheels and spike-pattern tires Unpainted polycarbonate body and undertray, and rear wing Decal sheet Ball differential grease, ceramic grease and anti-wear grease Box wrench, 1.5 mm hex wrench and wrenches Hook-and-loop tape, double-sided tape, nylon bands and antenna post Instruction manual Important: This is an assembly kit, not a ready-to-run vehicle. Motor, ESC, radio equipment, steering servo, drive battery, charger, transmitter batteries and paint are not included.

4.295,-

6.495,-

På lager 10
KJØP
-34%
Art.nr: TRX 104354-74-RED
Copied
Traxxas 104354-74-RED- Slash Mudboss BL-2s Short Course Dirt Oval Racer RTR - RED Note that the Slash Mudboss will change it's name to Slash Modified. The first batch/bacthes will have all box graphics, manual, partslist etc say Slash Mudboss though... Competition Ready The Slash® Mudboss dirt oval racer is engineered to deliver competition-tuned track performance right out of the box. Slash’s already legendary durability has been enhanced with new Extreme Heavy Duty suspension components and performance upgrades such as aluminum GTR shocks, Magnum 272R transmission, tough clipless body, and the fast and reliable BL-2s brushless power system. Features: BL-2s™ brushless power for fast and consistent lap times Pro Series Magnum 272R™ Transmission Aluminum GTR™ shocks with TiN shafts Low-CG chassis New Extreme Heavy Duty components Durable, reinforced clipless body with molded wing Replica Hoosier® Angle Block tires BL-2s Brushless Power System The BL-2s brushless power system delivers more speed, quicker acceleration, and a more responsive throttle. Improved efficiency, high-speed ball bearings, and an internal cooling fan allow Slash Mudboss to run battery after battery for all-day race sessions. With no brushes to wear out, the BL-2s 3300 kV motor can last the entire racing season with minimal maintenance. Extreme Heavy Duty Components Extreme Heavy Duty components come factory-installed on Slash Mudboss for game-changing durability. Key drivetrain and suspension components are beefed-up with extra material for ultimate strength. From HD suspension arms to the upgraded axles, Slash Mudboss gets you to the finish line no matter how rough the racing action gets. Pro Series Magnum 272R Transmission The Magnum 272R transmission maximizes racing performance and durability for hard-hitting torque of brushless power systems. The 272R features an aluminum motor plate, all-metal gears, and a sealed silicone-filled 4-gear differential. The low-CG design concentrates weight as low as possible over the rear axle for improved traction and handling. Clipless Race Body Slash MudBoss comes Ready-To-Race® with a clipless body that requires no assembly and exceeds even the best custom designs. A heavily reinforced internal cage utilizes robust top and side bracing to ward off crash damage and protect the rear tires. Traxxas clipless technology holds the body firmly in place from start to finish with quick and easy removal on the pit bench. Replica Hoosier Tires Replica Hoosier Angle Block tires come mounted to graphite gray “steelie” wheels for an authentic race-prepped look. The tires are molded in a special rubber compound that balances durability and traction for consistent performance lap after lap. The large tread block design utilizes aggressive siping for maximum grip and predictable handling at the limit. Aluminum GTR Shocks GTR shocks represent the peak of racing technology. The color-matched PTFE-coated aluminum shock bodies hold over 70% more oil than Ultra Shocks™ and their slick titanium-nitride coated shafts resist scuffing, increase durability, and eliminate “stiction.” X-ring seals keep oil in and dirt out for smooth, consistent damping, and plush suspension action. Spring preload and ride height changes are as simple as turning the threaded collars. Model Specs: Length: 656mm Width: 313mm Ground Clearance: 35mm Weight (no battery): 2.55kg Height (overall): 216mm Wheelbase: 333mm Shock Length (front): 88mm - Long Shock Length (rear): 101mm - XX-Long Tires: Licensed Hoosier® Angle Block racing tires Tire Diameter: 109mm Wheels (front/rear): Graphite gray "steelie" wheels Wheel Diameter: 2.2 inches (56 mm) (outer) - 3.0 inches (76 mm) (inner) Speed Control: BL-2s™ electronic speed control Motor (electric): BL-2s™ 3300 kV sensorless brushless Overall Drive Ratio: 9.10:1 Differential Type: Sealed, hardened steel bevel, limited slip Gear Pitch: 48 Chassis Structure/Material: Composite tub Drive System: 2WD Steering: Dual-bellcrank with integrated servo saver Radio System: TQ™ 2.4 GHz (2-channel) Servo: Waterproof digital 2075 servo (125 oz-in torque) Skill Level: 1 Battery Compartment (L/W/H): 165x50x23/25mm Motor Specs: Motor Name: BL-2s 3300 kV Motor Type: Sensorless brushless Motor Length: 80mm Motor Diameter: 36mm Motor Shaft Size: 3.17mm Motor Connector Type: Traxxas Quick Connect Motor Plug ESC Specs: ESC Name: BL-2s Electronic Speed Control ESC Type: Brushless Sensorless Motor Connectors: Traxxas Quick Connect Motor Plug Battery Connectors: Traxxas High-Current Connector What’s In The Box: Slash Mudboss with BL-2s ESC and 3300 kV motor Quick Start Guide TQ™ 2.4 GHz radio system High quality maintenance tools What You’ll Need: Battery: Slash Mudboss requires a single NiMH or LiPo battery Charger: Traxxas EZ-Peak Live charger (2971) is recommended for easy and fast charging performance AA Alkaline Batteries: Four AA alkaline batteries for the transmitter

3.495,-

5.495,-

På lager 2
KJØP
-36%
Art.nr: TRX 104354-74-GRN
Copied
Traxxas 104354-74-GRN - Slash Mudboss BL-2s Short Course Dirt Oval Racer RTR - GREEN Note that the Slash Mudboss will change it's name to Slash Modified. The first batch/bacthes will have all box graphics, manual, partslist etc say Slash Mudboss though... Competition Ready The Slash® Mudboss dirt oval racer is engineered to deliver competition-tuned track performance right out of the box. Slash’s already legendary durability has been enhanced with new Extreme Heavy Duty suspension components and performance upgrades such as aluminum GTR shocks, Magnum 272R transmission, tough clipless body, and the fast and reliable BL-2s brushless power system. Features: BL-2s™ brushless power for fast and consistent lap times Pro Series Magnum 272R™ Transmission Aluminum GTR™ shocks with TiN shafts Low-CG chassis New Extreme Heavy Duty components Durable, reinforced clipless body with molded wing Replica Hoosier® Angle Block tires BL-2s Brushless Power System The BL-2s brushless power system delivers more speed, quicker acceleration, and a more responsive throttle. Improved efficiency, high-speed ball bearings, and an internal cooling fan allow Slash Mudboss to run battery after battery for all-day race sessions. With no brushes to wear out, the BL-2s 3300 kV motor can last the entire racing season with minimal maintenance. Extreme Heavy Duty Components Extreme Heavy Duty components come factory-installed on Slash Mudboss for game-changing durability. Key drivetrain and suspension components are beefed-up with extra material for ultimate strength. From HD suspension arms to the upgraded axles, Slash Mudboss gets you to the finish line no matter how rough the racing action gets. Pro Series Magnum 272R Transmission The Magnum 272R transmission maximizes racing performance and durability for hard-hitting torque of brushless power systems. The 272R features an aluminum motor plate, all-metal gears, and a sealed silicone-filled 4-gear differential. The low-CG design concentrates weight as low as possible over the rear axle for improved traction and handling. Clipless Race Body Slash MudBoss comes Ready-To-Race® with a clipless body that requires no assembly and exceeds even the best custom designs. A heavily reinforced internal cage utilizes robust top and side bracing to ward off crash damage and protect the rear tires. Traxxas clipless technology holds the body firmly in place from start to finish with quick and easy removal on the pit bench. Replica Hoosier Tires Replica Hoosier Angle Block tires come mounted to graphite gray “steelie” wheels for an authentic race-prepped look. The tires are molded in a special rubber compound that balances durability and traction for consistent performance lap after lap. The large tread block design utilizes aggressive siping for maximum grip and predictable handling at the limit. Aluminum GTR Shocks GTR shocks represent the peak of racing technology. The color-matched PTFE-coated aluminum shock bodies hold over 70% more oil than Ultra Shocks™ and their slick titanium-nitride coated shafts resist scuffing, increase durability, and eliminate “stiction.” X-ring seals keep oil in and dirt out for smooth, consistent damping, and plush suspension action. Spring preload and ride height changes are as simple as turning the threaded collars. Model Specs: Length: 656mm Width: 313mm Ground Clearance: 35mm Weight (no battery): 2.55kg Height (overall): 216mm Wheelbase: 333mm Shock Length (front): 88mm - Long Shock Length (rear): 101mm - XX-Long Tires: Licensed Hoosier® Angle Block racing tires Tire Diameter: 109mm Wheels (front/rear): Graphite gray "steelie" wheels Wheel Diameter: 2.2 inches (56 mm) (outer) - 3.0 inches (76 mm) (inner) Speed Control: BL-2s™ electronic speed control Motor (electric): BL-2s™ 3300 kV sensorless brushless Overall Drive Ratio: 9.10:1 Differential Type: Sealed, hardened steel bevel, limited slip Gear Pitch: 48 Chassis Structure/Material: Composite tub Drive System: 2WD Steering: Dual-bellcrank with integrated servo saver Radio System: TQ™ 2.4 GHz (2-channel) Servo: Waterproof digital 2075 servo (125 oz-in torque) Skill Level: 1 Battery Compartment (L/W/H): 165x50x23/25mm Motor Specs: Motor Name: BL-2s 3300 kV Motor Type: Sensorless brushless Motor Length: 80mm Motor Diameter: 36mm Motor Shaft Size: 3.17mm Motor Connector Type: Traxxas Quick Connect Motor Plug ESC Specs: ESC Name: BL-2s Electronic Speed Control ESC Type: Brushless Sensorless Motor Connectors: Traxxas Quick Connect Motor Plug Battery Connectors: Traxxas High-Current Connector What’s In The Box: Slash Mudboss with BL-2s ESC and 3300 kV motor Quick Start Guide TQ™ 2.4 GHz radio system High quality maintenance tools What You’ll Need: Battery: Slash Mudboss requires a single NiMH or LiPo battery Charger: Traxxas EZ-Peak Live charger (2971) is recommended for easy and fast charging performance AA Alkaline Batteries: Four AA alkaline batteries for the transmitter

3.495,-

5.495,-

På lager 2
KJØP
-36%
Art.nr: 05003229-3
Copied
Futaba T6PV 6-kanals F-4G rattradio med R404SBS-E mottaker Futaba T6PV er et avansert 2,4 GHz radiosystem for RC-biler, utviklet for førere som ønsker rask respons, presis styring og omfattende programmeringsmuligheter. Radioen passer til både baneracing, drifting, crawling, større RC-biler og andre radiostyrte kjøretøy. T6PV kombinerer avanserte funksjoner fra Futabas toppmodell T10PX med den brukervennlige betjeningen fra T4PM Plus. Resultatet er en moderne 6-kanals rattradio med fargeskjerm, flere radiosystemer, telemetri og omfattende muligheter for individuell tilpasning. Med Futabas raske F-4G-system og støtte for UR-kompatible servoer kan radiosystemet levere svært rask respons. Den justerbare Response/Feeling-funksjonen gjør det samtidig mulig å tilpasse reaksjonene etter kjørestil, underlag og personlige preferanser. Hovedegenskaper 6-kanals radiosystem med Futaba F-4G-teknologi Futaba R404SBS-E mottaker inkludert 3,2-tommers bakbelyst LCD-fargeskjerm Seks systemmoduser: F-4G, T-FHSS, S-FHSS og tre Mini-Z-moduser UR-modus for ekstra rask respons med kompatible servoer Justerbar Response/Feeling-funksjon Modelltyper: Normal, Big og Drift Avanserte innstillinger for crawler og firehjulsstyring Telemetri med kompatible mottakere og sensorer Programmerbare brytere, trimknapper og kanaler S.BUS/S.BUS2-servoprogrammering Gyro-Link og MC-Link for kompatibelt Futaba-utstyr MicroSD-kortplass for modelldata og programvareoppdateringer Justerbar rattposisjon, rattvinkel og ergonomi Avanserte racingfunksjoner, miksing og tidtaking Futaba F-4G – rask og presis signaloverføring F-4G er Futabas moderne radiosystem for avanserte RC-biler. Systemet er utviklet for rask kommunikasjon mellom sender og mottaker, og gir presis kontroll ved høye hastigheter og raske styrebevegelser. Med kompatible UR-servoer kan T6PV benytte Futabas UR-modus (Ultra Response). Denne er beregnet for førere som ønsker svært rask servorespons, eksempelvis innen konkurransekjøring. Response/Feeling: Selv om raskest mulig respons kan være ønskelig på en racerbane, kan en mer kontrollert reaksjon være fordelaktig på krevende underlag. Response/Feeling lar føreren justere følelsen fra mildere til mer aggressiv respons. Når funksjonen er deaktivert, oppnås raskest respons. Viktig: UR-modus krever kompatible servoer. En vanlig servo får ikke automatisk UR-egenskaper ved å kobles til en F-4G-mottaker. Støttede radiosystemer Futaba T6PV støtter flere overføringssystemer. Dette gjør radioen spesielt interessant for kunder som allerede har Futaba-mottakere i forskjellige RC-modeller. F-4G: Opptil 6 kanaler. Futabas moderne høyhastighetssystem med støtte for telemetri og kompatible UR-servoer. T-FHSS: Opptil 4 kanaler. Støtter kompatible T-FHSS-mottakere og telemetri. S-FHSS: Opptil 6 kanaler. Gir mulighet til å bruke flere eldre Futaba-mottakere. Mini-Z EVO: For kompatible Kyosho Mini-Z EVO-modeller. Mini-Z EVO2: For kompatible Kyosho Mini-Z EVO2-modeller. Mini-Z FHSS: Krever kompatibel Kyosho FS-RM005-modul. Merk: T6PV støtter ikke T-FHSS SR som eget radiosystem. Kompatible servoers SR-innstillinger kan likevel benyttes gjennom F-4G-systemets servofunksjoner. Kompatible Futaba-mottakere Følgende mottakermodeller er oppført som kompatible med Futaba T6PV. Velg riktig overføringssystem i radiosenderen før mottakeren kobles til. F-4G-mottakere Futaba R404SBS Futaba R404SBS-E R404SBS-E er beregnet for elektriske RC-biler og har intern antenne. R404SBS har ekstern antenne og er et alternativ når mottakeren skal brukes i andre typer kjøretøy, inkludert nitro- og bensinmodeller. T-FHSS-mottakere Futaba R334SBS Futaba R334SBS-E Futaba R324SBS Futaba R314SB Futaba R314SB-E Futaba R304SB Futaba R304SB-E Disse benyttes i vanlig T-FHSS-modus. T6PV støtter ikke T-FHSS SR-modus, selv om enkelte mottakere også har støtte for denne modusen med andre Futaba-sendere. S-FHSS-mottakere Futaba R202GF Futaba R203GF Futaba R204GF-E Futaba R214GF-E Futaba R2104GF S-FHSS er spesielt nyttig for kunder som ønsker å bruke eldre kompatible Futaba-mottakere. Telemetri er ikke tilgjengelig i S-FHSS-modus. Viktig om mottakervalg: Kontroller alltid mottakerens spesifikasjoner, antennetype, bruksområde og eventuelle firmwarekrav. Ikke alle mottakere er godkjent for nitro- eller bensinmodeller. Kompatibilitet med radiosystemet betyr heller ikke nødvendigvis at alle funksjoner eller kanaler er tilgjengelige. Avanserte racingfunksjoner T6PV har en omfattende racingmeny med funksjoner for å tilpasse bilens oppførsel til førerens kjørestil og forholdene på banen. Steering EXP: Justerer hvordan styringen reagerer rundt rattets midtstilling. Throttle EXP: Justerer gassresponsen for mer kontrollert eller aggressiv akselerasjon. Brake EXP: Tilpasser bremseresponsen. Steering Speed: Regulerer hvor raskt styreservoens utslag endres. Throttle Speed: Regulerer hastigheten på gassresponsen. Traction Control: Pulserende gassfunksjon som kan bidra til bedre kontroll under akselerasjon. A.B.S.: Pulserende bremsefunksjon som kan gjøre bilen lettere å kontrollere under bremsing. Start Function: Gir mulighet for forhåndsinnstilt gassrespons ved start. Engine Cut: Flytter gasservoen til en forhåndsbestemt posisjon for å stoppe en forbrenningsmotor. Drag Racing / Trans Brake: Spesialfunksjon for drag racing og kontrollerte starter. Idle Up: Mulighet for å øke tomgangsinnstillingen på modeller der dette er aktuelt. Drifting – tilpass styring og gyro Futaba T6PV har egen Drift-modelltype og flere funksjoner som er nyttige for moderne RWD-driftbiler. Med Steering EXP og Steering Speed kan føreren finjustere styreresponsen. Throttle EXP gir tilsvarende kontroll over gasspådraget. Radioen har også Gyro Mixing og Gyro-Link for kompatible Futaba-gyroer. Dette gjør det mulig å tilpasse gyroens oppførsel og innstillinger uten å måtte gjøre alle justeringene direkte på gyroens kontrollenhet. For drifting kan også Traction Control-funksjonen brukes til pulserende motorrespons, avhengig av bilens elektronikk og oppsett. Crawling – firehjulsstyring, vinsj og flere motorer T6PV er også interessant for avanserte crawlerbygg. Med opptil seks kanaler og omfattende miksefunksjoner kan radioen styre mer enn bare gass og vanlig forhjulsstyring. 4WS Mixing: Styring av både for- og bakaksel med kompatible servoer. Dual ESC Mixing: Kontroll av to separate fartsregulatorer, eksempelvis i spesialbygde crawlere. Winch Mixing: Funksjon for styring av kompatibel elektrisk vinsj. Program Mixing: Fem programmerbare miksefunksjoner for å kombinere kanaler og styresignaler. Channel Assignment: Mulighet for å tilordne styring og gass til forskjellige kanaler. End Point Adjustment: Individuell justering av servoenes maksimale utslag. Sub Trim: Finjustering av servoenes nøytralposisjon. Funksjonene gjør det mulig å bygge avanserte oppsett med flere styreservoer, to motorer eller annet ekstrautstyr. Antall tilgjengelige funksjoner avhenger av mottaker, kanaler og tilkoblet elektronikk. Miksefunksjoner Steering Mixing – styringsmiksing Brake Mixing – bremsemiksing Gyro Mixing – gyrostyring 4WS Mixing – firehjulsstyring Dual ESC – to fartsregulatorer CPS Mixing 1, 2 og 3 – styring av kompatible Futaba CPS-1 lyskontrollere Tank Mixing – miksing for beltekjøretøy og stridsvogner Program Mixing 1–5 – programmerbare miksefunksjoner Winch Mixing – vinsjstyring Programmering av servo, gyro og fartsregulator Futaba T6PV har egne funksjoner for oppsett og programmering av kompatibelt Futaba-utstyr. S.BUS Servo: Justering av parametere på kompatible Futaba S.BUS- og S.BUS2-servoer. UR Servo Settings: Innstillinger for kompatible Futaba UR-servoer. Gyro-Link: Justering av kompatible Futaba-gyroer. MC-Link: Programmering av kompatible Futaba elektroniske fartsregulatorer. Servo View: Viser servoutslagene på kanalene og gjør det enklere å kontrollere oppsett og miksing. Tilgjengelige innstillinger avhenger av hvilket Futaba-utstyr som er tilkoblet. Modellminne og modelladministrasjon Radioen har funksjoner for å administrere forskjellige RC-modeller med individuelle oppsett. Model Select – velg lagret modell Model Copy – kopier modellinnstillinger Model Name – gi modellene egne navn Model Reset – nullstill modellinnstillinger Model Type – Normal, Big eller Drift MicroSD – lagring og håndtering av modelldata Dette er spesielt praktisk dersom samme radiosender skal brukes til flere RC-biler med forskjellige mottakere, servoer og fartsregulatorer. Grunnleggende justeringer og sikkerhetsfunksjoner Servo Reverse: Endrer rotasjonsretningen på servo eller annen kanalstyrt elektronikk. Sub Trim: Finjusterer nøytralposisjonen. End Point: Begrenser maksimalt servoutslag og gass-/bremseutslag. D/R og ATL: Justerer styreutslag og bremsebegrensning. Throttle Mode: Mulighet for nøytralbrems. Acceleration: Individuell justering av gass- og bremserespons nær nøytralpunktet. Fail-Safe: Programmerbar sikkerhetsfunksjon ved tap av radiosignal eller lav mottakerspenning. Channel Setting: Tilordning av styring og gass til ønskede kanaler. Fail-safe må stilles inn og testes korrekt før modellen tas i bruk. Telemetri og tidtaking Med kompatible mottakere og sensorer kan T6PV vise telemetridata direkte på radiosenderen. Telemetri støttes i F-4G- og T-FHSS-modus, men ikke i S-FHSS- eller Mini-Z-modus. Radioen har også flere nyttige tidsfunksjoner: Up Timer – opptelling av tid Fuel Down Timer – nedtelling, eksempelvis for kjøretid eller drivstoff Lap Timer – registrering av rundetider Lap Navigate Timer – tidsfunksjon for rundekjøring Lap List – gjennomgang av registrerte rundetider Total Timer – samlet driftstid for senderen Fargeskjerm og tilpassbare menyer Den store 3,2-tommers LCD-fargeskjermen gir god oversikt over radioens innstillinger. Betjeningen skjer blant annet med jog-kontroll og programmerbare knapper. Justerbar skjermlysstyrke Justerbar tid før skjermen dimmes Tilpasset startskjerm Egne menyer med ofte brukte funksjoner Programmerbare trimknapper DT1–DT6 Programmerbart dreiehjul DL1 Programmerbare brytere SW1–SW3 Tilpasning av END/DIR-knappene Justerbare knappelyder og varsler Varsling om lav batterispenning Varsling dersom senderen blir stående på MicroSD-kort og programvareoppdateringer Futaba T6PV har MicroSD-kortplass som blant annet kan brukes til: Lagring av modelldata Lagring av telemetridata Visning av egne modellbilder på senderen Programvareoppdateringer Støtter MicroSD/SDHC med FAT32-formatering. SDXC støttes ikke. Minnekort kjøpes separat. Radioen har også funksjon for oppdatering av kompatible mottakere. Ergonomi og justeringsmuligheter T6PV er konstruert for å ligge godt i hånden og kan tilpasses førerens grep og kjørestil. Justerbar rattposisjon med APA-adapter 5-graders vinkeladapter Mulighet for endret rattvinkel Større ratt inkludert Justerbar gassavtrekker Alternative grepstørrelser som ekstrautstyr Justering av rattets og avtrekkerens nøytralposisjon Standard grepstørrelse er M. Alternative gummigrep i størrelse S og L kan kjøpes separat. Ytterligere justering av gassavtrekkeren er mulig med kompatibelt ekstrautstyr. Strømforsyning Radiosenderen kan brukes med AA-batterier eller kompatible oppladbare senderbatterier. Futaba oppgir blant annet følgende kompatible batteripakker: FT2F1100B – LiFe FT2F1700B V2 – LiFe FT2F2100B V2 – LiFe LT2F2000B – LiPo HT5F1800B – NiMH Kompatibel LF-02-lader kan brukes med støttede LiFe-batterier. Velg alltid riktig batteritype i senderens innstillinger slik at batterivarslingen fungerer korrekt. Batterier og lader følger ikke med. Tekniske spesifikasjoner – Futaba T6PV Produsent: Futaba Modell: T6PV Artikkelnummer hos SamiRC: 05003229-3 Type: Digital 6-kanals rattradio Frekvens: 2,4 GHz Kanaler: Opptil 6, avhengig av radiosystem Radiosystemer: F-4G, T-FHSS, S-FHSS, Mini-Z EVO, Mini-Z EVO2 og Mini-Z FHSS Skjerm: 3,2" LCD-fargeskjerm Telemetri: F-4G og T-FHSS Minnekort: MicroSD/SDHC, FAT32 Modelltyper: Normal, Big og Drift Programmerbare trimknapper: DT1–DT6 Programmerbart dreiehjul: DL1 Programmerbare brytere: SW1–SW3 Strømforsyning: AA eller kompatibel oppladbar batteripakke Medfølgende mottaker: R404SBS-E Medfølgende Futaba R404SBS-E mottaker R404SBS-E er en kompakt 2,4 GHz F-4G-mottaker med intern antenne, beregnet for elektriske RC-biler. Modell: Futaba R404SBS-E Radiosystem: F-4G Frekvens: 2,4 GHz Driftsspenning: 3,7–7,4 V S.BUS2-tilkobling Dimensjoner: 25,5 × 20,7 × 10,6 mm Vekt: ca. 7,2 gram Intern antenne Beregnet for elektriske RC-modeller Viktig: Kanal 5 og 6 benyttes via S.BUS2 med kompatibel servo eller SBD-2. R404SBS-E skal ikke brukes i nitro- eller bensindrevne modeller. Dette følger med i pakken Futaba T6PV 6-kanals radiosender Futaba R404SBS-E mottaker APA-M adapter for endring av rattposisjon Monteringsskruer 32-graders rattadapter L-bremsehendel 5-graders vinkeladapter Ratt med større diameter UR/SR-merke Sekskantnøkkel Brukerveiledning Merk: Batterier, batterilader og MicroSD-kort følger ikke med. Hvem passer Futaba T6PV for? Futaba T6PV passer for RC-entusiaster som ønsker ett avansert radiosystem til flere biler, og som setter pris på raske styresignaler, omfattende programmeringsmuligheter og fleksibel mottakerkompatibilitet. Radioen er særlig aktuell for konkurransekjøring, drifting og avansert crawling, men fungerer også godt til vanlige RC-biler når man ønsker bedre kontroll og flere justeringsmuligheter enn en enkel standardradio tilbyr. Med støtte for både nyere F-4G-mottakere og flere eldre Futaba-systemer er T6PV et interessant valg både ved nybygg og oppgradering av eksisterende RC-modeller. English product description English product description – Click to expand   Futaba T6PV - 6-channel Radio - with R404SBS-E receiver High-middle radio with fastest response function This is a mid-high class transmitter that adds the elements of the T10PX to the operability of the T4PM Puls. The full-color display allows intuitive operation. In addition, by supporting the fastest system "F-4G", it is easier to feel the "response/feeling function" that gives stability to operation. The T6PV transmitter is compatible with "F-4G", "T-FHSS", "S-FHSS", and "MINI-Z" modes. The R404SBS and R404SBS-E are receivers compatible with "F-4G". F-4G system and UR mode provide high-speed response approaching that of the T10PX radio (*Note 1). Equipped with 6 system modes: F-4G, T-FHSS, S-FHSS, MINI-Z EVO, MINI-Z EVO2 & MINI-Z FHSS Although T-FHSS SR mode is not supported, the servo's "SR mode" can still be used in the servo settings of the F-4G system. Normal, Big, and Drift "Model Types" Also equipped with settings for crawlers Response/Feeling adjustment function: By adding a mild flavor while taking advantage of the high-speed response, it becomes easier to drive. Supports up to 6 channels (*Note 2) Lightest in its class & high balance design Equipped with micro SD card slot The micro SD card is used to save model data, telemetry data, display photos of your car on the transmitter, and when updating the software. (Micro SD card sold separately. Supports SD/SDHC, not SDXC. Make shure that the card is formatted with MS-DOS FAT32) New wheel unit/APA/APA angler/trigger (*Note 3) Grip rubber: In addition to the included size (M), you can choose a size that is easy to use from the optional grip rubber (S or L). Wheel position can be adjusted with the steering APA (Included: Steering APA (24.0) & Angle spacer (5°) Trigger end point adjustment: If you use the optional T10PX dedicated trigger setting parts set, you can adjust the end point in the throttle (=FWD) direction with the spacer, so you can adjust the throttle operation to your preferred feeling. Setup with high-brightness wide-angle full-color LCD and jog key Batteries (not included): Requires dry cell batteries (AA). Optional LiFe batteries (FT2F1100B, FT2F1700B V2, FT2F2100B V2) can also be used. For LiFe batteries, a non-contact charger (LF-02) can also be used. Optional batteries such as LiPo batteries for Tx (LT2F2000B) and nickel-metal hydride batteries for Tx (HT5F1800B) can also be used. *Note 1: Be sure to use servos that are compatible with UR mode. *Note 2: When using channels 5 and 6 in F-4G mode, use an S.BUS2 servo or SBD-2 with the S.BUS2 port on the R404SBS/R404SBS-E. *Note 3: Adjustable Positioning Adaptor - Adapter for changing position Functions and Specifications: Setup menu: Receiver settings (F-4G / T-FHSS / S-FHSS, and MINI-Z compatible) Please refer to here for a list of our receivers that support each system. MINI-Z is also compatible with MINI-Z EVO, MINI-Z EVO2, and MINI-Z FHSS (*Note 4). The telemetry function is only available in F-4G and T-FHSS modes. It cannot be used in S-FHSS and MINI-Z modes. *Note 4: MINI-Z FHSS requires the MINI-Z FS-RM005 module (manufactured by Kyosho Corporation). Servo view: Allows you to check the servo operation of all channels. You can check the operation when adjusting the steering angle or setting the mixing function. Throttle mode: Allows you to set the neutral brake, which applies the brakes when the throttle trigger is in the neutral position. Reverse: This function determines the direction in which servos and other devices operate in response to the operation of the steering, throttle, channel 3/4, and other auxiliary channels of the transmitter. Sub trim: Used when assembling a model to fine-tune the center position of the servo horn that serves as the reference for the servo horn of each servo and the linkage that connects the parts with rods. End point: Used during linkage to adjust the steering angle left and right, the throttle high side/brake side operation amount, and the up side/down side operation amount of channel 3/4 and other auxiliary channels. Fail-safe function: This function sets the servo operation position in case the receiver is unable to receive the transmitter signal for some reason or the receiver battery voltage drops. The failsafe, hold, and OFF modes will be automatically released when signals from the transmitter are received again. Acceleration: The throttle forward/brake ramp-up characteristics near neutral can be adjusted separately. Trim/dial settings: The functions that can be operated with the digital trim (DT1 to DT6) and dial (DL1) can be set. Switch settings: Select the functions to be operated with the push switches (SW1 to SW3) and set the operation method. Idle up: Used to improve engine starting by raising the idling when starting the engine of a gasoline engine car (boat). This function is also effective when you want to prevent braking when the power is turned off while driving due to the gear ratio settings or the motor used in an electric car. However, if you are using MC971CR, MC970CR, MC960CR, MC950CR, MC851C, MC602C, MC402CR, etc., as with the neutral brake function, turn on the idle up function switch after the ESC recognizes the neutral position and becomes operable. D/R, ATL Channel setting: This function allows you to assign steering or throttle to any channel. This is a convenient function when you want to use steering or throttle on a different channel, or when you want other channels to operate in the same way as steering or throttle. Model Menu: Model Select, Model Copy Model Name Delete Model (SD Card) Reset Data Model Type: You can use the default settings suitable for 1/5 models and drifting. Mixing Menu: Steering mixing Brake mixing Gyro mixing 4WS mixing Dual ESC CPS mixing (1,2,3): When using CPS-1 (optional), you can set the LED lighting pattern, etc. Tank mixing: Mixing for tracked vehicles such as tanks. Program mixing (1, 2, 3, 4, 5): It is also possible to set the mixing master to telemetry. Winch mixing: This mixing is effective for crawlers. Racing Menu: Curve (EXP): Steering, throttle, and brake can be set separately. Speed: Steering and throttle can be set separately. Traction control: By operating the throttle intermittently, you can steer smoothly and drive on the ideal line. In addition, in drift cars, you can reproduce a pseudo rev limiter sound by operating the motor intermittently in the high point direction. A.B.S.: In full-time 4WD cars, if you apply the brakes while cornering, the car will understeer, but by using this function, you can clear the corner smoothly. Start: Simply operate the throttle trigger slowly without losing grip, and the trigger position will automatically switch to the preset point, allowing for a smooth start. Engine cut: This function operates the throttle servo to a preset position (engine cut position) so that the engine can be stopped with a switch. Response/Feeling: This function makes the response milder when you feel that the servo response is too sensitive and difficult to operate. The mild side will slow the response, and the aggressive side will make the response faster. Feeling adjustment OFF provides the fastest response. Drag racing (trans brake): Stopping the vehicle with the throttle (trigger) fully open and releasing the trans brake allows for sharp acceleration. Accessories Menu: Timer: Use one of four timers: up timer, fuel down timer, lap timer, and lap navigate timer. Lap list: Call up when checking lap memory data (each lap time) stored by operating the lap timer. S.BUS servo: Dedicated function to change parameters of Futaba S.BUS / S.BUS2 servos. Change UR servo settings MC (ESC) link: Allows you to set the ESC. Gyro link: Allows you to set the gyro. Index table: Allows you to display an index table for DD cars. Gear ratio table: Calculates the final reduction ratio from the input pinion gear, spur gear, and secondary reduction ratio of the gearbox, and displays it in a list. END/DIR button settings: Allows you to customize the END/DIR button as a button to call up your favorite menu. Home screen display settings: Allows you to customize the display of the home screen. Custom menu editing: Allows you to create your own frequently used functions. Warning display: Low battery alarm, power off forget warning, MIX warning System Menu: Display settings: You can set the backlight brightness, dimming time, etc. System information: You can set the user name, display language, and telemetry information units using the jog key. It also displays the software version. Buzzer: You can adjust the switch/trim/jog key operation sounds and the warning alarm sound pitch. Battery settings: By setting the battery type, the appropriate battery alarm voltage can be achieved. Total timer: You can display the accumulated time that the power has been ON on the home screen. LED settings: You can set the brightness and lighting method of the pilot LED light (always on, off, linked to the backlight). Adjuster: You can correct the neutral position and operating angle of the steering wheel and throttle trigger. Receiver update: You can update via the radio control. Included accessories: APA-M wheel position change adapter Bag of mounting screws 32° wheel adapter L brake lever 5° angle spacer Large diameter steering wheel UR/SR label Instruction manual Hexagonal wrench Included receiver: R404SBS-E (for 1/10 electric cars)

3.795,-

5.195,-

På lager 2
KJØP
-27%
Art.nr: EFL08275
Copied
Eflite T-28 Trojan 1.1m PNP The E-flite® T-28 Trojan 1.1m updates the longtime sport scale favorite with modern-day upgrades, making it even better equipped for scale-like and sport flying — plus higher speeds and higher energy aerobatics so it’s more fun to fly than ever before! Key Features Updated and upgraded to offer improved scale-like and sport flying, higher speed and higher energy aerobatic capabilities Easy to take off, fly and land, making it a perfect "next step" after a trainer, an excellent first scale or low-wing model In The Box (1) E-flite® T-28 Trojan 1.1m with: (1) Brushless Outrunner Motor (installed) (1) 30A Brushless ESC (installed) (4) Servos (installed) (1) Product Manual Needed to Complete (1) Full-range 4+ Channel Transmitter and Receiver (1) 3S 11.1V or 4S 14.8V 1800–2200mAh LiPo with EC3™ or IC3™ Connector (1) Compatible LiPo Charger Introduction NEW MOVES FROM AN OLD FAVORITE Introduced as a ParkZone® model more than a decade ago, the T-28 Trojan 1.1m quickly became a favorite of low-time to experienced pilots alike! It had the scale looks of the North American Aviation T-28 Trojan used as a trainer by the Navy from 1952 to 1984, yet flew better than most sport RC models because of its incredible handling with no bad habits. The model's simplicity, durability, and easy handling made it especially popular with low-time pilots moving up to their first sport, low wing or warbird model after mastering a trainer. Plus, the convenient size allowed it to be flown at large parks and sports fields and transported easily without disassembly. Now the T-28 has been updated and upgraded to be more powerful, more capable, and more fun to fly than ever before! Stronger and reinforced parts combine with the more powerful 3S and 4S compatible power system featuring a telemetry-capable ESC to deliver higher speeds and higher energy aerobatic performance — while offering the same slow and scale-like, sport flying and easy handling capabilities the original was always known for. Features Updated and upgraded to offer improved scale-like and sport flying, higher speed and higher energy aerobatic capabilities Easy to take off, fly and land, making it a perfect "next step" after a trainer, an excellent first scale or low-wing model Specially tuned motor compatible with 3S and 4S batteries without the need for modifications or upgrades Popular 3S and 4S 1800–2200mAh batteries deliver excellent performance and flight times Easy to fly with innovative and optional-use SAFE® Select flight envelope protection 4-channel control with four (4) factory-installed servos and linkages for full aerobatic capability Stronger motor mount, nose gear steering arm, and wing spar for added reinforcement Lightweight yet durable composite-reinforced EPO construction Factory-finished in a fully-painted, high-visibility trim scheme Fast and easy assembly – no glue required Overview A T-28 AT THE TOP OF ITS CLASS Updated and upgraded, including a fully-painted, high-visibility trim scheme, the E-flite® T-28 Trojan 1.1m reaffirms its status as an excellent "next step" model for low-time pilots who have mastered a trainer and are looking for their first low-wing, sport or warbird model — while expanding its performance for experienced pilots with higher speed and higher energy aerobatic capabilities! With a common 3S 1800–2200mAh LiPo battery, the brushless power system featuring a specially-tuned motor delivers plenty of thrust and speed for low-time to intermediate pilots. Or, install a 4S battery for more speed and unlimited vertical performance without modifications or upgrades! Four servos and linkages are factory-installed for full aerobatic capability to perform loops, rolls, knife-edge, inverted flying, and more. The composite-reinforced EPO airframe includes stronger parts to handle the higher speeds and additional aerobatic capabilities, and for improved durability overall. Final assembly is fast and easy, no glue required, and the T-28 fits into almost any vehicle fully assembled — or the wing can be removed for even easier transport and storage. Any traditional RC flying field with paved, dirt or grass surfaces makes a suitable flying site, although skilled pilots can fly in smaller areas such as large parks or sports fields. The T-28 is inherently stable like the full-scale trainer platform, but the BNF® Basic version, featuring a Spektrum™ AR631 receiver, gives low-time and intermediate pilots the added benefits of exclusive AS3X® and optional-use SAFE® Select stabilization technologies. Best of all the ESC included with both versions is telemetry-capable to deliver real-time battery voltage, current, motor RPM, and other data via compatible receivers (including the AR631 included with the BNF Basic version) and Spektrum™ AirWare™ equipped transmitters. And it all adds up to offer improved scale-like and sport flying, higher speed and higher energy aerobatic capabilities to deliver a sport scale flying experience you simply can't get anywhere else! More Capable The lightweight yet durable composite-reinforced EPO airframe has been updated to handle more power, higher speeds and higher energy aerobatics. A stronger motor mount and nose gear steering arm, plus a new spar to better reinforce the wing, combine to make the T-28 Trojan 1.1m more capable than ever before. More Powerful The factory-installed brushless power system features a 30-amp telemetry-capable ESC plus a specially-tuned motor to deliver an abundance of thrust with a 3S LiPo battery, or more speed and unlimited vertical performance with a 4S battery without the need for any modifications or upgrades. Telemetry Capable The T-28 Trojan 1.1m is equipped with an ESC that can provide a variety of real-time power system related telemetry data including motor RPM, current, battery voltage and more via compatible receivers (including the AR631 installed in the BNF® Basic version) and Spektrum™ AirWare™ equipped transmitters (including the DX6e and 8e, DX6 G2/G3 and 8 G2, the DX9, the NX6, 8 and 10, the iX12, iX20 and others) while you fly. Easy Assembly No glue is required for final assembly, and you can have the T-28 Trojan 1.1m ready to fly in less time than it takes to charge a battery! And although it's conveniently sized to fit fully assembled in just about any vehicle, you can also remove the wing for even easier storage and transport. Plug-N-Play® Completion Level This Plug-N-Play (PNP) model comes out of the box with a factory-installed power system and servos that are ready to connect to the compatible receiver of your choice (sold separately). Simply install the receiver, finish any final assembly, and fly! Product Specifications Charger Sold Separately Receiver Sold Separately Radio Sold Separately Minimum Required Radio 4-channel Product Weight 1080g (38oz) with 4S battery, 855g (30oz) without battery Landing Gear Fixed, tricycle type Motor Type Brushless Speed Control Included Wing Area 314 sq. in. (20.3 sq. dm) Battery Sold Separately Motor Size 3626 Product Length 36" (914 mm) Steering Steerable nose gear Flaps No Material EPO Completion Level Plug-N-Play Minimum Speed Control 30A Propeller Size 9.5 Recommended Motor Battery 4S 2200mA 30C LiPo Power Type Electric Servos Included Skill Level Level 2 Trim Scheme Colors Yellow and black Wingspan 44" (1118 mm)

1.995,-

3.295,-

På lager 1
KJØP
-39%
Art.nr: 6308-22
Copied
Pro-Spec Short Course Rear Spring Assortment for Pro-Spec Rear SC Shocks 6308-31 This is a Rear Spring Pack for Pro-Spec SC Shocks. Do you need to dial in the Spring Rate on your Pro-Spec Shocks? This is the Spring Pack for you! This Spring Pack includes every spring that Pro-Line offers for the Rear Pro-Spec Shocks in one pack. From Blue (Super Soft) to Green (Soft) to Stock Yellow (Medium) to Red (Hard) to Purple (Super Hard), this pack has them all. Get Dialed in with Pro-Line’s new Spring Pack! What's Included: Pro-Spec Rear SC Shock Springs (10 pcs) Fits: 6308-01 Pro-Spec Rear SC Shocks 6308-31 Pre-Assembled Pro-Spec Rear SC Shocks Specs: Spring Rate Chart - New Shock Design (lbf/in) Front 3.2 3.4 3.6 3.8 4.0 Rear 2.0 2.2 2.4 2.6 2.8

199,-

429,-

På lager 21
KJØP
-54%
Art.nr: 1158-00
Copied
Disse dekkene passer fint til Rustler også. Felger som anbefales er Pro-Line Split Six 2.2"/3.0" Turn your Short Course into a sand slinging super truck with Pro-Line's Sling Shot SC tires. With 10 monster grabbing ¼” tall paddles sand and snow are easily overcome. Pair with the 1157-00 Features: Made from durable XTR compound 10 ¼” tall paddles Molded foam insert and supplemental insert included 2.2 outer bead and 3.0 inner bead Works on glueable wheels and Pro-Line Bead-Loc wheels Fits Slash /Blitz/SCRT10 Rear, Slash 4x4 Front/Rear What's included: Sling Shot SC Tires Left & Right (2 pcs) Closed Cell Inserts (2 pcs

249,-

489,-

På lager 23
KJØP
-49%
Art.nr: 10197-203
Copied
PROLINE 1/10 Front Runner S3 2WD Front 2.2"/2.7" Drag Racing Tire (2) Pro-Line is ready to change the No Prep Drag game once again with a true next-generation front tire designed for maximum performance: the Front Runner Tire! Named after the front tires found in full-size drag racing, the Pro-Line Front Runner Tire was built from the ground up to be as lightweight and narrow as possible while still maintaining a scale appearance. The outside of the tire features a standard 2.2" bead, so it will look like all the regular front tires from the outside, but the inside of the tire has a 2.7" flat bead for reduced rubber weight. Combine with Pro-Line's Showtime Front Runner 2.2"/2.7" Wheel (PL2803-03), which eliminates the need for tire foam, and you have the ultimate Drag Racing front tire and wheel. Now that top drag racers are consistently dropping sub 2-second runs, every gram of weight counts. Don't get stuck dragging around heavy front tires; get your own set of Front Runners today! Features: All-new Ground up Design for Maximum Performance 2.2"/2.7" Mounting Beads Super Narrow and Lightweight Combine with Pro-Line's Showtime Front Runner 2.2"/2.7" Wheels (PL2803-03) Eliminates the Need for Tire Foam Maintains Scale Appearance Named After Full-Size Drag Racing Tires Made in the USA Included: (2) Front Runner 2.2"/2.7" 2WD Front S3 Drag Tires Fits: Pro-Line Showtime Front Runner 2.2"/2.7" Wheels (PL2803-03)

99,-

399,-

På lager 37
KJØP
-75%
Art.nr: 2803-03
Copied
PROLINE 1/10 Showtime Front Runner Front 2.2"/2.7" 12mm Drag Wheels (2) Black It's Showtime! Pro-Line has an all-new 2.2"/2.7" Black Drag Front Wheel featuring a scale spoke pattern that mimics full-size drag wheels. The Showtime Front Runner 2.2"/2.7" wheel is a perfect fit for Pro-Line's new Front Runner 2.2"/2.7" Tires (PL10197-203) and is designed to be super lightweight and narrow for maximum performance. The Showtime Front Runner Wheels are a strong and lightweight 12mm hex wheel making them the ideal choice for performance drag racing. The wheel offset is ideal for Losi® 22S™ No Prep Drag Car, 2wd Slash® trucks converted to no-prep Drag Racing cars, and AE DR10. This wheel is designed to eliminate the need for foam insert completely for the ultimate in lightweight performance. The Showtime Front Runner Wheel is proudly made by Pro-Line and Made in the USA. Launch your no-prep Dragster to the next level with the Pro-Line Showtime Front Runner Drag Wheels today! Features: Scale Spoke Pattern Mimics Full-Size Drag Wheels Perfect fit for Pro-Line's New Front Runner 2.2"/2.7" Tires (PL10197-203) Super Narrow and Lightweight Eliminates the Need for Tire Foam 12mm Hex Wheel for Use with Losi® 22S™ No Prep Drag Car, Slash® and AE DR10 Wheel Made from High-Strength, Durable Black Nylon Made in the USA Fits: Losi® 22S™ No Prep Drag Car (LOS03035/LOS03041) Front with Pro-Line's Front Runner 2.2"/2.7" Tires (PL10197-203) Slash® 2wd Front with Pro-Line's Front Runner 2.2"/2.7" Tires (PL10197-203) AE DR10 Front with Pro-Line's Front Runner 2.2"/2.7" Tires (PL10197-203) Slash® 4x4 Front with Pro-Line's Front Runner 2.2"/2.7" Tires (PL10197-203) Included: (2) Showtime Front Runner 2.2"/2.7" Front Drag Wheels in Black Specifications: Outer Diameter: 77 mm Scale: 1/10 Suit: Drag Racing Width: 14 mm Drive: 12mm Hex  

49,-

239,-

På lager 35
KJØP
-79%
Art.nr: TRX 104354-74-ORNG
Copied
Traxxas 104354-74-ORANGE- Slash Mudboss BL-2s Short Course Dirt Oval Racer RTR - ORANGE Note that the Slash Mudboss will change it's name to Slash Modified. The first batch/bacthes will have all box graphics, manual, partslist etc say Slash Mudboss though... Competition Ready The Slash® Mudboss dirt oval racer is engineered to deliver competition-tuned track performance right out of the box. Slash’s already legendary durability has been enhanced with new Extreme Heavy Duty suspension components and performance upgrades such as aluminum GTR shocks, Magnum 272R transmission, tough clipless body, and the fast and reliable BL-2s brushless power system. Features: BL-2s™ brushless power for fast and consistent lap times Pro Series Magnum 272R™ Transmission Aluminum GTR™ shocks with TiN shafts Low-CG chassis New Extreme Heavy Duty components Durable, reinforced clipless body with molded wing Replica Hoosier® Angle Block tires BL-2s Brushless Power System The BL-2s brushless power system delivers more speed, quicker acceleration, and a more responsive throttle. Improved efficiency, high-speed ball bearings, and an internal cooling fan allow Slash Mudboss to run battery after battery for all-day race sessions. With no brushes to wear out, the BL-2s 3300 kV motor can last the entire racing season with minimal maintenance. Extreme Heavy Duty Components Extreme Heavy Duty components come factory-installed on Slash Mudboss for game-changing durability. Key drivetrain and suspension components are beefed-up with extra material for ultimate strength. From HD suspension arms to the upgraded axles, Slash Mudboss gets you to the finish line no matter how rough the racing action gets. Pro Series Magnum 272R Transmission The Magnum 272R transmission maximizes racing performance and durability for hard-hitting torque of brushless power systems. The 272R features an aluminum motor plate, all-metal gears, and a sealed silicone-filled 4-gear differential. The low-CG design concentrates weight as low as possible over the rear axle for improved traction and handling. Clipless Race Body Slash MudBoss comes Ready-To-Race® with a clipless body that requires no assembly and exceeds even the best custom designs. A heavily reinforced internal cage utilizes robust top and side bracing to ward off crash damage and protect the rear tires. Traxxas clipless technology holds the body firmly in place from start to finish with quick and easy removal on the pit bench. Replica Hoosier Tires Replica Hoosier Angle Block tires come mounted to graphite gray “steelie” wheels for an authentic race-prepped look. The tires are molded in a special rubber compound that balances durability and traction for consistent performance lap after lap. The large tread block design utilizes aggressive siping for maximum grip and predictable handling at the limit. Aluminum GTR Shocks GTR shocks represent the peak of racing technology. The color-matched PTFE-coated aluminum shock bodies hold over 70% more oil than Ultra Shocks™ and their slick titanium-nitride coated shafts resist scuffing, increase durability, and eliminate “stiction.” X-ring seals keep oil in and dirt out for smooth, consistent damping, and plush suspension action. Spring preload and ride height changes are as simple as turning the threaded collars. Model Specs: Length: 656mm Width: 313mm Ground Clearance: 35mm Weight (no battery): 2.55kg Height (overall): 216mm Wheelbase: 333mm Shock Length (front): 88mm - Long Shock Length (rear): 101mm - XX-Long Tires: Licensed Hoosier® Angle Block racing tires Tire Diameter: 109mm Wheels (front/rear): Graphite gray "steelie" wheels Wheel Diameter: 2.2 inches (56 mm) (outer) - 3.0 inches (76 mm) (inner) Speed Control: BL-2s™ electronic speed control Motor (electric): BL-2s™ 3300 kV sensorless brushless Overall Drive Ratio: 9.10:1 Differential Type: Sealed, hardened steel bevel, limited slip Gear Pitch: 48 Chassis Structure/Material: Composite tub Drive System: 2WD Steering: Dual-bellcrank with integrated servo saver Radio System: TQ™ 2.4 GHz (2-channel) Servo: Waterproof digital 2075 servo (125 oz-in torque) Skill Level: 1 Battery Compartment (L/W/H): 165x50x23/25mm Motor Specs: Motor Name: BL-2s 3300 kV Motor Type: Sensorless brushless Motor Length: 80mm Motor Diameter: 36mm Motor Shaft Size: 3.17mm Motor Connector Type: Traxxas Quick Connect Motor Plug ESC Specs: ESC Name: BL-2s Electronic Speed Control ESC Type: Brushless Sensorless Motor Connectors: Traxxas Quick Connect Motor Plug Battery Connectors: Traxxas High-Current Connector What’s In The Box: Slash Mudboss with BL-2s ESC and 3300 kV motor Quick Start Guide TQ™ 2.4 GHz radio system High quality maintenance tools What You’ll Need: Battery: Slash Mudboss requires a single NiMH or LiPo battery Charger: Traxxas EZ-Peak Live charger (2971) is recommended for easy and fast charging performance AA Alkaline Batteries: Four AA alkaline batteries for the transmitter

3.495,-

5.495,-

På lager 2
KJØP
-36%
Art.nr: TRX 104354-74-PINK
Copied
Traxxas 104354-74-PINK- Slash Mudboss BL-2s Short Course Dirt Oval Racer RTR - PINK Note that the Slash Mudboss will change it's name to Slash Modified. The first batch/bacthes will have all box graphics, manual, partslist etc say Slash Mudboss though... Competition Ready The Slash® Mudboss dirt oval racer is engineered to deliver competition-tuned track performance right out of the box. Slash’s already legendary durability has been enhanced with new Extreme Heavy Duty suspension components and performance upgrades such as aluminum GTR shocks, Magnum 272R transmission, tough clipless body, and the fast and reliable BL-2s brushless power system. Features: BL-2s™ brushless power for fast and consistent lap times Pro Series Magnum 272R™ Transmission Aluminum GTR™ shocks with TiN shafts Low-CG chassis New Extreme Heavy Duty components Durable, reinforced clipless body with molded wing Replica Hoosier® Angle Block tires BL-2s Brushless Power System The BL-2s brushless power system delivers more speed, quicker acceleration, and a more responsive throttle. Improved efficiency, high-speed ball bearings, and an internal cooling fan allow Slash Mudboss to run battery after battery for all-day race sessions. With no brushes to wear out, the BL-2s 3300 kV motor can last the entire racing season with minimal maintenance. Extreme Heavy Duty Components Extreme Heavy Duty components come factory-installed on Slash Mudboss for game-changing durability. Key drivetrain and suspension components are beefed-up with extra material for ultimate strength. From HD suspension arms to the upgraded axles, Slash Mudboss gets you to the finish line no matter how rough the racing action gets. Pro Series Magnum 272R Transmission The Magnum 272R transmission maximizes racing performance and durability for hard-hitting torque of brushless power systems. The 272R features an aluminum motor plate, all-metal gears, and a sealed silicone-filled 4-gear differential. The low-CG design concentrates weight as low as possible over the rear axle for improved traction and handling. Clipless Race Body Slash MudBoss comes Ready-To-Race® with a clipless body that requires no assembly and exceeds even the best custom designs. A heavily reinforced internal cage utilizes robust top and side bracing to ward off crash damage and protect the rear tires. Traxxas clipless technology holds the body firmly in place from start to finish with quick and easy removal on the pit bench. Replica Hoosier Tires Replica Hoosier Angle Block tires come mounted to graphite gray “steelie” wheels for an authentic race-prepped look. The tires are molded in a special rubber compound that balances durability and traction for consistent performance lap after lap. The large tread block design utilizes aggressive siping for maximum grip and predictable handling at the limit. Aluminum GTR Shocks GTR shocks represent the peak of racing technology. The color-matched PTFE-coated aluminum shock bodies hold over 70% more oil than Ultra Shocks™ and their slick titanium-nitride coated shafts resist scuffing, increase durability, and eliminate “stiction.” X-ring seals keep oil in and dirt out for smooth, consistent damping, and plush suspension action. Spring preload and ride height changes are as simple as turning the threaded collars. Model Specs: Length: 656mm Width: 313mm Ground Clearance: 35mm Weight (no battery): 2.55kg Height (overall): 216mm Wheelbase: 333mm Shock Length (front): 88mm - Long Shock Length (rear): 101mm - XX-Long Tires: Licensed Hoosier® Angle Block racing tires Tire Diameter: 109mm Wheels (front/rear): Graphite gray "steelie" wheels Wheel Diameter: 2.2 inches (56 mm) (outer) - 3.0 inches (76 mm) (inner) Speed Control: BL-2s™ electronic speed control Motor (electric): BL-2s™ 3300 kV sensorless brushless Overall Drive Ratio: 9.10:1 Differential Type: Sealed, hardened steel bevel, limited slip Gear Pitch: 48 Chassis Structure/Material: Composite tub Drive System: 2WD Steering: Dual-bellcrank with integrated servo saver Radio System: TQ™ 2.4 GHz (2-channel) Servo: Waterproof digital 2075 servo (125 oz-in torque) Skill Level: 1 Battery Compartment (L/W/H): 165x50x23/25mm Motor Specs: Motor Name: BL-2s 3300 kV Motor Type: Sensorless brushless Motor Length: 80mm Motor Diameter: 36mm Motor Shaft Size: 3.17mm Motor Connector Type: Traxxas Quick Connect Motor Plug ESC Specs: ESC Name: BL-2s Electronic Speed Control ESC Type: Brushless Sensorless Motor Connectors: Traxxas Quick Connect Motor Plug Battery Connectors: Traxxas High-Current Connector What’s In The Box: Slash Mudboss with BL-2s ESC and 3300 kV motor Quick Start Guide TQ™ 2.4 GHz radio system High quality maintenance tools What You’ll Need: Battery: Slash Mudboss requires a single NiMH or LiPo battery Charger: Traxxas EZ-Peak Live charger (2971) is recommended for easy and fast charging performance AA Alkaline Batteries: Four AA alkaline batteries for the transmitter

3.495,-

5.495,-

På lager 2
KJØP
-36%
Art.nr: TRX 104354-74-BLUE
Copied
Traxxas 104354-74-BLUE- Slash Mudboss BL-2s Short Course Dirt Oval Racer RTR - BLUE Note that the Slash Mudboss will change it's name to Slash Modified. The first batch/bacthes will have all box graphics, manual, partslist etc say Slash Mudboss though... Competition Ready The Slash® Mudboss dirt oval racer is engineered to deliver competition-tuned track performance right out of the box. Slash’s already legendary durability has been enhanced with new Extreme Heavy Duty suspension components and performance upgrades such as aluminum GTR shocks, Magnum 272R transmission, tough clipless body, and the fast and reliable BL-2s brushless power system. Features: BL-2s™ brushless power for fast and consistent lap times Pro Series Magnum 272R™ Transmission Aluminum GTR™ shocks with TiN shafts Low-CG chassis New Extreme Heavy Duty components Durable, reinforced clipless body with molded wing Replica Hoosier® Angle Block tires BL-2s Brushless Power System The BL-2s brushless power system delivers more speed, quicker acceleration, and a more responsive throttle. Improved efficiency, high-speed ball bearings, and an internal cooling fan allow Slash Mudboss to run battery after battery for all-day race sessions. With no brushes to wear out, the BL-2s 3300 kV motor can last the entire racing season with minimal maintenance. Extreme Heavy Duty Components Extreme Heavy Duty components come factory-installed on Slash Mudboss for game-changing durability. Key drivetrain and suspension components are beefed-up with extra material for ultimate strength. From HD suspension arms to the upgraded axles, Slash Mudboss gets you to the finish line no matter how rough the racing action gets. Pro Series Magnum 272R Transmission The Magnum 272R transmission maximizes racing performance and durability for hard-hitting torque of brushless power systems. The 272R features an aluminum motor plate, all-metal gears, and a sealed silicone-filled 4-gear differential. The low-CG design concentrates weight as low as possible over the rear axle for improved traction and handling. Clipless Race Body Slash MudBoss comes Ready-To-Race® with a clipless body that requires no assembly and exceeds even the best custom designs. A heavily reinforced internal cage utilizes robust top and side bracing to ward off crash damage and protect the rear tires. Traxxas clipless technology holds the body firmly in place from start to finish with quick and easy removal on the pit bench. Replica Hoosier Tires Replica Hoosier Angle Block tires come mounted to graphite gray “steelie” wheels for an authentic race-prepped look. The tires are molded in a special rubber compound that balances durability and traction for consistent performance lap after lap. The large tread block design utilizes aggressive siping for maximum grip and predictable handling at the limit. Aluminum GTR Shocks GTR shocks represent the peak of racing technology. The color-matched PTFE-coated aluminum shock bodies hold over 70% more oil than Ultra Shocks™ and their slick titanium-nitride coated shafts resist scuffing, increase durability, and eliminate “stiction.” X-ring seals keep oil in and dirt out for smooth, consistent damping, and plush suspension action. Spring preload and ride height changes are as simple as turning the threaded collars. Model Specs: Length: 656mm Width: 313mm Ground Clearance: 35mm Weight (no battery): 2.55kg Height (overall): 216mm Wheelbase: 333mm Shock Length (front): 88mm - Long Shock Length (rear): 101mm - XX-Long Tires: Licensed Hoosier® Angle Block racing tires Tire Diameter: 109mm Wheels (front/rear): Graphite gray "steelie" wheels Wheel Diameter: 2.2 inches (56 mm) (outer) - 3.0 inches (76 mm) (inner) Speed Control: BL-2s™ electronic speed control Motor (electric): BL-2s™ 3300 kV sensorless brushless Overall Drive Ratio: 9.10:1 Differential Type: Sealed, hardened steel bevel, limited slip Gear Pitch: 48 Chassis Structure/Material: Composite tub Drive System: 2WD Steering: Dual-bellcrank with integrated servo saver Radio System: TQ™ 2.4 GHz (2-channel) Servo: Waterproof digital 2075 servo (125 oz-in torque) Skill Level: 1 Battery Compartment (L/W/H): 165x50x23/25mm Motor Specs: Motor Name: BL-2s 3300 kV Motor Type: Sensorless brushless Motor Length: 80mm Motor Diameter: 36mm Motor Shaft Size: 3.17mm Motor Connector Type: Traxxas Quick Connect Motor Plug ESC Specs: ESC Name: BL-2s Electronic Speed Control ESC Type: Brushless Sensorless Motor Connectors: Traxxas Quick Connect Motor Plug Battery Connectors: Traxxas High-Current Connector What’s In The Box: Slash Mudboss with BL-2s ESC and 3300 kV motor Quick Start Guide TQ™ 2.4 GHz radio system High quality maintenance tools What You’ll Need: Battery: Slash Mudboss requires a single NiMH or LiPo battery Charger: Traxxas EZ-Peak Live charger (2971) is recommended for easy and fast charging performance AA Alkaline Batteries: Four AA alkaline batteries for the transmitter

3.495,-

5.495,-

På lager 2
KJØP
-36%
  • klarna-dark.png
  • vipps-orange.png
  • mastercard-full.png
  • visa.png
  • paypal.png