Hopp til innhold
Hjem / Reservedeler/Option-parts / Reservedeler Bil / Diverse deler mange merker / HPI Racing 1430 One-Way Bearing For Pull Start .21 BB

HPI Racing 1430 One-Way Bearing For Pull Start .21 BB

Art.nr: 1430

295,-

Hpi Racing

Hpi Racing
På lager: 2

Produktet er midlertidig utsolgt. Dersom du ønsker å motta en epost når vi får det inn på lager, kan du legge igjen epostadressen din i skjemaet under.

Informasjon

This is the One-Way bearing for the HPI Nitro Star 21BB engine.
 ** Also fits the Roto Start for the Savage.**
 This One-Way Bearing allows the recoil starter to grab
 the crankshaft to start the engine and spin freely in the opposite direction.

 

 


FEATURES

Steel construction

 


INCLUDES

One one-way bearing
 One installation instruction sheet

 


REQUIREMENTS

Installing in recoil unit

 


SPECIFICATIONS

 Overall Length: 12mm (.472")
 Hex Width: 12mm (.472")
 Inner Diameter: 6mm (.218")

Produsent

Hpi Racing

Hpi Racing

Kunder kjøpte også

Hovedbilde Sunpadpow SW256411 Li-Po Battery 4S 14,8V 5200mAh 110C ...
Sunpadpow SW256411 Li-Po Battery 4S 14,8V 5200mAh 110C ...
SUNPADOW SW256411 - ERC Plus 5200mAh-14.8V-4S1P-110C LiPo Hard Case Battery - EC5 Specs: Type: 14.8V 4S1P Capacity: 5200mAh Power: 76.96Wh Rated: 110C Power Connector: EC5 Balance Connector: XH Power Wires: 12AWG Size: 138x47.5x39mm Weight: 459g Suitable for: Any type of RC car/boat

949,-

999,-

KJØP
-5%
Hovedbilde 6s 5000mAh - 45C - Gens Ace G-Tech EC5 Hovedbilde 6s 5000mAh - 45C - Gens Ace G-Tech EC5
6s 5000mAh - 45C - Gens Ace G-Tech EC5
6s 5000mAh - 45C - Gens Ace G-Tech EC5. Batteriet leveres ferdig med EC5 batteriplugg og G-Tech XH balanseringplugg. Størrelsen er 158x48x45mm. Passer godt til større helikoptere, biler og fly. PS! Produkt kan avvike fra video. Klippet er lagt til som relevant opplysning til produktet, men er ikke nødvendigvis identisk. Innhold i en produktvideo, testvideo eller et review kan avvike fra produktet som selges. Dette kan gjelde farger, spesifikasjoner, versjonsforskjeller, regionsforskjeller m.m. Det er produktets navn, beskrivelse og bilder du skal forholde deg til ved kjøp av varen.   G-Tech Har man G-tech lader og batteri, vil lader kommuniserer med batteriet via balanseringspluggen. Her får laderen informasjon om batteriet som celleantall, spenning, kapasitet og helse. Laderene velger da korrekt ladeprogram og ladestyrke automatisk. Ladestyrke kan endres manuelt etter oppstart ved behov.G-Tech kontakten er kompatibel med vanlige LiPo-ladere med XH-balanseringsport så man kan lade dette batteriet på samme måte som vanlige LiPo-batterier. Spesfikasjoner: Kapasitet: 5000mAh Spenning: 6s 22.2V Vekt: 720gram Størrelse: 158x48x45mm Strømplugg: EC5

1.395,-

KJØP
Hovedbilde Dynomaxx 9694 Charge Lead EC5 with 4mm Banana ...
Dynomaxx 9694 Charge Lead EC5 with 4mm Banana ...
DynoMAX B9694 - EC5 Charging Lead for Chargers with 4mm Banana Outputs This is a charging lead for batteries with a EC5 connector. It fits chargers that are equipped with 4mm banana connectors. Specs: Battery Connector: EC5 Charger Connector: 4mm Banana Bullets Wires: 14AWG Length: 500mm

85,-

KJØP
Hovedbilde DynoMAX B9668 Charging Lead Futaba RX to XT60 20AWG ... Hovedbilde DynoMAX B9668 Charging Lead Futaba RX to XT60 20AWG ...
DynoMAX B9668 Charging Lead Futaba RX to XT60 20AWG ...
DynoMAX B9668 - Futaba RX Charge Lead for Chargers with an XT60 Output This is a charging lead for batteries with a Futaba RX connector. It fits the latest SkyRC chargers that are equipped with a XT60 male output/charging connector. Specs: Battery Connector: Futaba RX Charger Connector: XT60 Wires: 20AWG Length: 500mm

65,-

KJØP
Hovedbilde Robinson Racing 7738 Slipper Unit GEN3 38T Revo 3.3
Robinson Racing 7738 Slipper Unit GEN3 38T Revo 3.3
This is the Robinson Gen3 High Performance Slipper Unit for the Traxxas Revo 3.3.     FEATURES Steel spur gear Aluminum slipper plate Heavy-duty slipper pad Ball bearing supported spur gear     INCLUDES One spur gear, one slipper plate, one slipper pad, ball bearing, instructions and decals     REQUIREMENTS Installation following the included instructions     SPECIFICATIONS Spur Gear Tooth Count: 38 Pitch: 1 module     COMMENTS Robinson recommends using their extra hard clutch bells RRPC8015 - RRPC8020 with this spur gear. ajw 11-03-10

759,-

KJØP
Hovedbilde HPI 86060 Racing Engine Mount Savage 21
HPI 86060 Racing Engine Mount Savage 21
This is the Stock Replacement Engine Mount for the HPI Savage. This part holds the engine to the chassis. FEATURES Cast aluminum construction Natural aluminum color INCLUDES One engine mount Four 3x12mm cap head machine screws REQUIREMENTS Nothing. This is a direct replacement part. SPECIFICATIONS C.D. between engine mounting holes 21mm (same side) 37mm (across sides) COMMENTS This mount is uniquely shaped for the HPI Savage.

139,-

KJØP
Hovedbilde SkyRC eN20 Charger NiMh 1-2-3A 4-8cells 20W 240VAC
SkyRC eN20 Charger NiMh 1-2-3A 4-8cells 20W 240VAC
SKYRC eN20 NiMH/NiCd Charger is an economic, high quality 100-240V AC charger, designed for charging NiMH and NiCad batteries from 4-8 cells. The circuit power is 20W and max charge current can reach to 3A. There are three kinds of charge current 1A/2A/3A that can be selected. You could select the proper charge current according to battery capacity. There is one LED indicating the charger status (ready to charge/charging/charge finish). The operation of the charger is also very simple. There is a toggle switch in the charger which can be used to select charge current. After you power on the charger, select the charge current, connect the battery and charger, the charger will start working.   Explanation of LED Status: CHARGE LED STATUS CHARGE STATUS LED Flashes Green The Charger is Ready LED Glows Red Battery Charger in process LED Glows Green Battery charger is fully charged Specifications: AC Input Voltage: 100-240V, 50-60HZ Output Power: 20W Charging Current (Selected by Switch): 1A, 2A, 3A Battery Type (Selected by Switch): NiMH/NiCd Battery Cell Count: 4-8 cells 1 LED for Charging Status Dimension: 69.4 x 110.7 x 40.5 mm Weight: 175 g Included: eN20 Charger 240VAC adapter with Euro connector Charging lead with Tamiya connector Specifications: AC Input Voltage: 100-240V, 50-60HZ Output Power: 20W Charging Current (Selected by Switch): 1A, 2A, 3A Battery Type (Selected by Switch): NiMH/NiCd Battery Cell Count: 4-8 cells 1 LED for Charging Status Dimension: 69.5 x 110 x 40.4 mm Weight: 175 g

349,-

399,-

KJØP
-13%
Hovedbilde Vapex Receiver Battery NiMH 4,8V 2500mAh Cube
Vapex Receiver Battery NiMH 4,8V 2500mAh Cube
Vapex Instant-series of NiMH batteries with very low self-discharge level. Battery: 4-cell (4.8V) NiMH AA 2500 mAh Receiver battery Connector: Futaba Length: 53 mm Width: 29 mm Height: 29 mm Weight: 117 g

199,-

KJØP
Hovedbilde DynoMAX 9685 Charge Lead Futaba RX with 4mm Banana ...
DynoMAX 9685 Charge Lead Futaba RX with 4mm Banana ...
D-MAX™ Charging Harness for Radio Batteries with Futaba Connector This is a charge lead for charging TX & RX radio batteries with a Futaba connector. Specs: Length: 50cm Wires: 20AWG Charger Connectors: 4mm male bullets Battery Connector: Futaba RX

69,-

KJØP
Hovedbilde HPI 1428 Racing Pull Start Assembly .21/.25 F4.1BB
HPI 1428 Racing Pull Start Assembly .21/.25 F4.1BB
This is the stock replacement Recoil Assembly for the HPI .21BB Engine. This is attached to the engine backplate.     FEATURES Assembled pull-starter     INCLUDES One recoil assembly Three 3x8mm cap head machine mounting screws     REQUIREMENTS Using the original one-way bearing, or purchasing 1430     SPECIFICATIONS Thickness: 19mm (0.75") C.D. between mounting holes: 27mm (1.07")     COMMENTS This recoil is made specifically for the HPI .21BB engine.

379,-

KJØP
Hovedbilde Traxxas 2470A Tires & Wheels 2,2
Traxxas 2470A Tires & Wheels 2,2" Alias/Tracer Medium ...
Tires & wheels, assembled (Tracer 2.2" black chrome wheels, Alias 2.2" tires) (2) (Bandit rear, medium compound with foam inserts) (TSM rated)

319,-

349,-

KJØP
-9%
Hovedbilde Hovedbilde
"Bulk" Traxxas 6516 2-Channel TQ 2.4GHz Transmitter ...
NB! Dette er både radio og mottager. This is the Traxxas 2-Channel TQ 2.4GHz Transmitter with TRX 6519 receiver. **This transmitter is compatible only with the TRX 6519 receiver and does NOT accept the Docking Base accessory.** FEATURES Replacement transmitter for several Traxxas vehicles that use the TQ 2.4GHz radio sytem Steering trim adjustment knob INCLUDES Traxxas 2-Channel TQ 2.4GHz Transmitter Receiver REQUIREMENTS Four AA batteries

795,-

1.095,-

Ikke på lager
-27%
Hovedbilde Traxxas 2849X LiPo 3S 11.1V 4000mAh 25C w/iD Connector
Traxxas 2849X LiPo 3S 11.1V 4000mAh 25C w/iD Connector
This is the Traxxas Power Cell 11.1V 4000mAh 25C 3S LiPo Battery.     FEATURES Semi rigid construction does not require a hard case and eliminates  wire harness connectors that can loosen and fail  Engineered specifically to fit Traxxas models  New high current connector with gold-plated copper terminals and  integrated balance connector  iD Auto Battery Identification allows Traxxas iD equipped chargers to  automatically set and optimize charge settings for specific battery  MAXX cable high-efficiency 12 gauge silicone jacketed wire   INCLUDES Traxxas Power Cell 11.1V 4000mAh 25C LiPo 3S Battery with High  Current Connector and Integrated Balance Plug   REQUIREMENTS LiPo compatible charger such as the Traxxas EZ-Peak Plus  LiPo charging bag   SPECIFICATIONS  Configuration: 3S1P  Continuous Discharge: 25C (100A)  Max Burst Rate: 50C (200A)  Watt Hours: 44.40  Charge Rate: 1C (4A)  Dimensions: 5.3 x 1.02 x 1.7" (135 x 26 x 43mm)  Weight: 11.1oz (316g)   COMMENTS ALWAYS use a LiPo-approved Charger  ALWAYS use a LiPo Cell Balancer  NEVER Charge over 4.20V per cell  NEVER Trickle Charge  NEVER allow to Discharge below 3.2V per cell  NEVER disassemble or modify pack wiring in any way or puncture cells  NEVER place on combustible materials or leave unattended during  charging  ALWAYS Charge in a fireproof location  ALWAYS set charger's output volts to match battery volts  ALWAYS keep out of reach of children  

929,-

999,-

KJØP
-7%
Hovedbilde Traxxas 2970 EZ-Peak Plus 4A NiMH/LiPo AC Fast Charger ... Hovedbilde Traxxas 2970 EZ-Peak Plus 4A NiMH/LiPo AC Fast Charger ...
Traxxas 2970 EZ-Peak Plus 4A NiMH/LiPo AC Fast Charger ...
EZ-Peak® Plus 4-amp NiMH/LiPo Fast Charger with iD® Auto Battery Identification   One connection does it all! The Traxxas iD® battery system is the easiest and safest way to charge your Traxxas batteries. The EZ-Peak® Plus recognizes Traxxas iD batteries and in an instant automatically configures and optimizes the charger settings. There's no need to be a battery expert or learn how to navigate complex menus. Just plug in a Traxxas iD battery and EZ-Peak Plus (#2970) does all the work for you. The integrated balance connector on Traxxas LiPo iD batteries eliminates fragile balance wires and connectors, along with the need for external balance boards. At the press of a button, the EZ-Peak Plus' Storage Mode protects your LiPo battery investment by safely preparing the batteries for extended storage. 4-amp fast charging and advanced high-resolution peak detection deliver a perfect charge every time. The EZ-Peak Plus is backed by the Traxxas Lifetime Electronics Warranty for years of reliable service. 1, 2, 3... Easy Steps! ­ ­ QUICK FEATURES ON EZ-PEAK PLUS (#2970) CHARGER ­ Recognizes Traxxas iD® batteries to automatically program and optimize charger settings Charge progress indicator Optimized for faster LiPo balance charging One button LiPo storage charge protects your battery investment Advanced high-resolution peak detection delivers a perfect charge Easy to use interface Built-in cooling fan Advanced Mode for full manual control of charger settings Legacy support for all Traxxas High-Current Connectors Built-in balance ports for conventional LiPo batteries Charges 5-8-cell NiMH batteries Charges 2s and 3s LiPo batteries ­ ­     EZ-PEAK PLUS (#2970) SPECIFICATIONS AC Input: ­ 100–240 Volts Charge Current Range: ­ 1.0-4.0A (40W Max.) Discharge Current Range: ­ 500mAh Current Drain For Balance Ports: ­ 500mAh NiMH Battery Cell Count: ­ 5–8 Cells LiPo Cell Count: ­ 2–3 Cells Net Weight: ­ 365g Dimensions: ­ 146 x 123 x 53mm     MODEL 2970: EZ-Peak® Plus 4-amp NiMH/LiPo Fast Charger with iD® Auto Battery Identification.

699,-

769,-

KJØP
-9%
Hovedbilde ANSMANN AA RED LINE 5015563 4 PK LR6
ANSMANN AA RED LINE 5015563 4 PK LR6
Kvantum: 4 stk per pakke. 1.5 Volt per batteri. Passer alle plasser hvor du kan bruke AA-batterier.

29,-

39,-

KJØP
-26%
Hovedbilde Traxxas 3727A Battery Hold-Down Plate Gray (2)
Traxxas 3727A Battery Hold-Down Plate Gray (2)
           This is the Traxxas Battery Hold-Down Plate, Metal    Post and Body Clip replacement parts for the Rustler and Rustler XL truck. FEATURES: Gray plastic construction INCLUDES: One gray plastic hold-down plate,  (2 5/8" long, 3/8" wide and                  has 2 holes that attach to the posts).           Two metal posts  (aluminum with a hex shaped top and hole                  for the body clip, threaded on bottom).           Two steel body clips. COMMENTS: Body clips are bent for easier installation.

39,-

KJØP
Hovedbilde Traxxas 3018R Sealed XL-5 Forward/Reverse/Brake ESC
Traxxas 3018R Sealed XL-5 Forward/Reverse/Brake ESC
XL-5™ Waterproof FWD/REV ESC with Low Voltage Detection (LVD) Designed and engineered by Traxxas, the XL-5 Electronic Speed Control handles the elements while smoothly supplying power to the motor. This high-performance ESC is packed with impressive specifications that are normally only found on more expensive high-end replacement units. The XL-5 features a completely waterproof design, three throttle profiles, Thermal Shutdown Protection, 4-7 cell compatibility, and built-in BEC. High frequency operation combined with ultra-low resistance make the XL-5 an efficient and ultra-smooth fully proportional speed control. An exclusive feature on the XL-5 is the patented Training Mode™. This profile reduces the overall power output of the XL-5 by 50% making it easier for young or new drivers to develop their control skills before unleashing full-power operation. XL-5 is equipped with two-stage low-voltage detection (LVD) to allow LiPo battery use. The XL-5 is manufactured by Traxxas to ensure the highest level of quality and support. The XL-5 is backed by the Traxxas Lifetime Electronics Warranty. Traxxas High-Current Connector* The XL-5 ESC is equipped with the patented Traxxas high-current connectors for restriction-free current flow. Click here for more info about the patented Traxxas High-Current Connertor.     Patented Training Mode™ An exclusive feature that places the XL-5 ahead of the pack is the patented Training Mode. This feature reduces the overall power output of the XL-5 by 50% making it easier for new drivers to control their model.  When they're ready, simply change profiles to unleash full-throttle action.  Only Traxxas has it! XL-5 LVD Waterproof ESC Features Built-in two-stage low voltage detection (LVD) for Lithium Polymer (LiPo) battery use Innovative watersealed design 15-turn motor limit for 540 size motors 12-turn motor limit for 550 size motors Fully-proportional forward, reverse, and braking control Programmable with three drive profiles: Sport Mode – Fwd / Brake / Rev Race Mode – Fwd / Brake Training Mode* – 50% Fwd / Brake / 50% Rev EZ-Set® push-button setup Multi-color LED Thermal shutdown protection Efficient, low-loss MOSFET design Smooth, high-frequency operation Easy installation in Traxxas models Backed by the Traxxas Lifetime Electronics warranty   XL-5 LVD WATERPROOF ESC SPECIFICATIONS Input voltage: ­ 4-7 Cells (4.8 to 8.4 Volts DC) Case Size: ­ 1.23"W x 2.18"D x 0.61" H Weight: ­ 2.44 Ounce Motor Limit: ­ 15-turns** (540 Size) 12-turns** (550 Size) On Resistance Forward: ­ 0.007 Ohms On Resistance Reverse: ­ 0.014 Ohms BEC Voltage: ­ 6.0 VDC BEC Current: ­ 1A Power Wire: ­ 14 Gauge / 5" Input Harness Wire: ­ 26 Gauge / 9" PWM Frequency: ­ 1600 Hz Low Voltage Detection (LVD): ­ 2-Stage indicators, switchable (on or off) Thermal Protection: ­ Thermal shutdown Profile selection: ­ Sport Mode:     100% FWD, 100% brakes, 100% REV Race Mode:     100% FWD, 100% brakes, no REV Training Mode:*     50% FWD, 100% brakes, 50% REV Single-button setup: ­ Yes, Traxxas EZ-Set®

939,-

1.039,-

KJØP
-10%
Hovedbilde Traxxas 1726 Antenna Tube Blue Hovedbilde Traxxas 1726 Antenna Tube Blue
Traxxas 1726 Antenna Tube Blue
This is a replacement antenna tube. Antenna tubes are used to help secure and protect reciever antenna wires. INCLUDES: 1 blue antenna tube and 1 black antenna tube cap. SPECIFICATIONS: Length: 11"                 Outside Diameter: 1/8"

29,-

KJØP
Hovedbilde Traxxas 2843X LiPo 2S 7.4V 5800mAh 25C w/iD ...
Traxxas 2843X LiPo 2S 7.4V 5800mAh 25C w/iD ...
Passer til:   Stampede 4x4 Bandit Rustler Stampede Slash 4x4 og Slash Ultimate E-Maxx E-Revo 1/10 Slash 2WD Summit 1/10 Antall celler : 2 (7,4volt) Kapasitet : 5800mAh Strøm ledning tykkelse : 12 AWG Balanseringsplugg : JST-XH Max ladestyrke : 2C (10 amp) Kontinuerlig utlading: 25C (145A) Max utladning : 50C (290A) Lengde: 13,50 cm (med ledningen 14,00 cm) Bredde: 4,27 cm Høyde : 2,44 cm Vekt : 312 gram

819,-

899,-

KJØP
-9%
Hovedbilde Traxxas 3232X Super Duty Long Glow Plug
Traxxas 3232X Super Duty Long Glow Plug
This is the Traxxas Super Duty Long Glowplug. FEATURES: Ideal for all Traxxas engines including the 2.5, 2.5R and 3.3 engines           Suited for the varied throttle range of off-road racing           Medium heat range INCLUDES: One Traxxas Medium Heat Range Super Duty Long Glowplug with gasket REQUIRES: Plug wrench  for installing in cylinder head           Glow Fuel with 10%-20% nitro content  

119,-

139,-

Ikke på lager
-14%

SamiRC Norge AS

© 2026 SamiRC Norge AS - Powered by Mystore.no

Om oss

  • SamiRC Norge AS
  • Nils Lauritssøns vei 34
  • 0870 OSLO
  • Org. nr. MVA 928 644 979 Foretaksregisteret
  • Tlf: 46760019
  • post@samirc.no

Kundeservice

Nyhetsbrev

  • klarna-dark.png
  • vipps-orange.png
  • mastercard-full.png
  • visa.png
  • paypal.png