Hopp til innhold

Traxxas 6842R Spur Gear 32P 50T

Art.nr: TRX 6842R

39,-

Traxxas

Traxxas

På lager: 1

Produktet er midlertidig utsolgt. Dersom du ønsker å motta en epost når vi får det inn på lager, kan du legge igjen epostadressen din i skjemaet under.

Informasjon

This is the 32P 50T Spur Gear for the Slash 4x4 from Traxxas.


FEATURES: Black plastic construction


INCLUDES: 32P 50T Spur Gear for the Slash 4x4


REQUIRES: Installation in center differential


SPECS:    Pitch: 32P
          Teeth: 50T

Produsent

Dette er den beste merket for RC-BIL i hele Norge, nei vi kan vel si hele verden uten å trenge å være redd for at vi sier noe galt!

Kunder kjøpte også

These are 3mm Grub Screws from Traxxas. FEATURES: Hardened steel construction.           Hexagon socket drive insert. INCLUDES: (12) Grub Screws SPECS:    Size:  3mm  

39,-

KJØP
This is the Hold Down Battery Set for the 2WD Traxxas Slash. FEATURES: Black nylon construction INCLUDES: One Battery Hold Down           One Retainer Hold Down           One Battery Post           One Foam Spacer           One Angled Body Clip REQUIRES: Installation on the chassis

79,-

89,-

KJØP
-11%
Denne er også til dem som skal ha TRX 5552 og 5552X This is the Slipper Clutch Rebuild Kit for the Traxxas Slash 4x4 Vehicles. FEATURES: Steel construction INCLUDES: One Steel Disc           Three Friction Pads           Two Springs           One 4mm Lock Nut           One 5mm Lock Nut           Instructions REQUIRES: Disassembly of slipper clutch

119,-

Ikke på lager
Yeah Racing HD Tool Steel Front Universal Drive Shafts for Traxxas 1/10 Slash Stampede 4X4 Blue HD Universal drive shafts for Traxxas's 4x4 version of Slash and Stampede, made from "Tool Grade Steel", giving good tensile strength. Whilst the middle sleeve is made from Aluminum to keep weight low giving a good balance between weight and strength!   Features: For: Traxxas 1/10 Slash Stampede 4X4 Material: Steel/Aluminum   Include: Universal Drive Shafts (2 pcs) Accessories (1 pack) 

369,-

389,-

KJØP
-5%
This is the Input Shaft for use on the Traxxas Slash 4x4 Vehicles. FEATURES: Steel construction           Black in color INCLUDES: One Input Shaft           One Bearing Adapter           One Pin REQUIRES: Installation on the vehicle SPECS:    Length: 58mm (2.3")

79,-

KJØP
Traxxas 5352A - Rebuild kit, slipper clutch (steel disc/ friction pads (3)/ spring (1)/ 2x9.8mm pin/ 5x8mm MW/ 5.0mm NL (1)/ 4.0mm NL (1))   The slipper clutch rebuild kit includes a new steel disc, friction pads (3), spring, pin, 5x8 washer, 4 mm locking nut, and 5 mm locking nut. Fits 5351 pressure plate and hub. Traxxas Slipper Clutch Rebuild Kit Revo/T-Maxx Traxxas Slipper Clutch Rebuild Kit Revo/T-Maxx

99,-

KJØP
This is a Replacement Slipper Pressure Plate and Slipper Hub for the Revo.                  These are part of the slipper assembly. FEATURES: Aluminum construction INCLUDES: One slipper pressure plate           One slipper hub REQUIRES: Installation onto vehicle.

99,-

Ikke på lager
This is the optional Big Bore Shock Set for the                          Traxxas Slash.          These replace the plastic shocks that come stock with the kit. FEATURES: Strong aluminum construction, teflon coated           Anodized black with white springs           Completely assembled INCLUDES: Four fully assembled shocks with white springs           Mounting hardware           One bottle of silicone oil REQUIRES: Filling shocks with shock oil and assembling onto the model

799,-

899,-

Ikke på lager
-11%
This is the Suspension Pin Set for the Traxxas Slash 4X4.            The hinge pins hold the suspension arms to the bulkheads FEATURES: Durable steel construction           Silver in color INCLUDES: Four 51.5mm pins           Four 30mm pins REQUIRES: Installation on the Slash 4x4  

55,-

KJØP
Green Motor Plate

85,-

KJØP
This is a Traxxas 18 Tooth Pinion Gear for a 5mm Motor Shaft. FEATURES: Silver in color           Metal construction INCLUDES: (1) 18 Tooth Pinion Gear           (1) One 4mmx3.5mm set screw REQUIRES: Installation on motor shaft SPECS:    Outer Diameter: 15.5mm (0.61")           Inner Diameter: 5mm (0.20") Pitch 32P

69,-

79,-

KJØP
-13%
 This is the Receiver Box for the 1/10 scale Traxxas. FEATURES: Plastic construction, black in color INCLUDES: Upper and lower Case Halves with Wire Cover           Gasket           Two Foam Pads           Two 3x12mm Button Head Cap Screws           Two 3x6mm Button Head Cap Screws           Two 2.5x12mm Cap Screws           Instruction Sheet SPECS:    Box Dimensions: 1.6 x 1.7 x 2.1" (41 x 43 x 54.5mm)

149,-

KJØP
 This is the Battery Hold-downs and Tall Retainers                   for the Traxxas 1/10 Rally VXL rally car FEATURES: Made of black plastic. INCLUDES: One battery hold-down           One tall front hold-down retainer           One tall rear hold-down retainer SPECS:    hold-down, length:         7-5/8" (194mm)                      width:          1-1/4" (32mm)                      height:         3/8"   (10mm)           front retainer, length:    46mm   (1-13/16")                           width:     50mm   (2")                           thickness: 8.5mm  (5/16")           rear retainer, length:     48mm   (1-7/8")                          width:      42mm   (1-5/8")                          thickness:  17mm   (11/16") COMMENTS: The tall hold-down retainers allow for the use of taller,              multi-cell batteries.

89,-

99,-

KJØP
-10%
This is the Battery Hold-Down Front/Rear                         For the Traxxas 1/10 Rally VXL FEATURES: Made of black plastic INCLUDES: Three different pieces COMMENTS: This battery holder is a replacement part.

89,-

99,-

KJØP
-10%
This is the Camber Link Set for the Traxxas Telluride 4x4. FEATURES Plastic construction Fits front and rear suspension Non-adjustable INCLUDES Two Front and two Rear Camber Links Two Plastic Inserts

39,-

KJØP
This is the Rear Driveshaft Assembly for the Traxxas Telluride 4x4. FEATURES Plastic and steel construction Assembled and ready to install INCLUDES Left and Right Rear Driveshaft Sections with Screw Pin

119,-

129,-

KJØP
-8%
OBS: Dette er G2-utgaven. Sjekk at denne passer mot din ESC. Overview This LED program box is for programming HobbyWing brushless ESCs. Its friendly interface makes ESC programming easy and quick. It’s compact, portable and very applicable for field use.  It works with the following HobbyWing products: 1. Platinum V1/V2 series & FlyFun V5 series of brushless aircraft ESCs.  2. XeRun series (not all), EzRun series & QuicRun series of brushless car ESCs.  3. SeaKing series of brushless boat ESCs.   Specifications Size:88x58x14mm(LxWxH) Weight:40g Input Voltage: 4.8V—8.4V(a separate battery is needed for powering this program box when ESC has no built-in/external BEC)

175,-

KJØP
Driveshaft assembly, front, heavy duty (1) (left or right) (fully assembled, ready to install)/ screw pin (1)

119,-

KJØP
Tires & wheels, assembled, glued (black wheels, gravel pattern tires, foam inserts) (2) (TSM rated)

329,-

KJØP
Gear, 11-T pinion (0.8 metric pitch, compatible with 32-pitch) (fits 5mm shaft)/ set screw

69,-

KJØP
Gear, 13-T pinion (0.8 metric pitch, compatible with 32-pitch) (fits 5mm shaft)/ set screw

59,-

69,-

KJØP
-14%
Bellcrank bushings (plastic) (5x8x2.5mm) (4)

39,-

KJØP
This is the Cover Gear/Wire Retainer                       For the Traxxas 1/10 Rally VXL FEATURES: Made of black plastic. INCLUDES: One cover gear           One wire retainer

39,-

KJØP
Easy and professional results can be yours with Tamiya's paint markers. Use them as you would a marking pen. The marker is a small, easy to use pen containing enamel paint formulated for the painting of plastics. Even the unskilled painter can now achieve beautiful results on their models. For expert modelers, it is indispensable for detailing painting and saving time. Excellent for wood, metal, glass as well as on all plastics. Contents: 8 grams (F)

49,-

99,-

KJØP
-51%
Shock tower, rear Rustler 4x4

79,-

KJØP
  • klarna-dark.png
  • vipps-orange.png
  • mastercard-full.png
  • visa.png
  • paypal.png