Hopp til innhold
-11%

Traxxas Disruptor VXL-4s Self-Righting 660mm Blue

Art.nr: TRX 106064-4-BLUE

4.795,-

5.395,-

- 11%
Traxxas

Traxxas

** Ikke på lager

Produktet er midlertidig utsolgt. Dersom du ønsker å motta en epost når vi får det inn på lager, kan du legge igjen epostadressen din i skjemaet under.

Informasjon

Traxxas TRX106064-4-BLUE - Disruptor 4s with Self-Righting - BLUE





Features:

  • FAST 64+KPH Speed
  • RELIABLE 4s Power
  • 26-INCH Deep-V Stability
  • RAPID RIGHT™ Self-Righting Security
  • RUGGED Construction


FULL-THROTTLE, NON-STOP FUN
The all-new 4s Disruptor® is the one boat that holds nothing back. Pin the throttle and Disruptor’s deep-V hull launches hard on its way to 64+KPH on a single 4s LiPo battery. At 66cm long, Disruptor is perfectly sized to be quick and agile on small ponds and stable in open water. Disruptor is purpose-built by Traxxas for the wildest stunts and unlimited fun—all with self-righting security.



RAPID RIGHT SECURITY
There’s no need to back off the throttle or tone down the fun with Disruptor's Rapid Right security. Take full advantage of 4s Velineon® brushless horsepower anytime, anywhere. If Disruptor should land upside down, applying reverse full throttle rights the boat almost instantly and gets you back in the action.



AGILE HANDLING
Disruptor’s perfectly sized hull delivers agile handling for tight turns with equally impressive 64+KPH speed. A new low-CG design concentrates weight inboard along the centerline for perfect weight distribution. Hammer the throttle and Disruptor gets on plane quickly with lightning-fast reflexes and high-speed stability.



NEW 4s POWER SYSTEM
The Velineon VXL-4s Marine brushless power system is a clean-slate design optimized to deliver maximum thrust on a single 4s LiPo battery. The all-new brushless outrunner motor is a model of efficiency and power, combining thunderous torque with high-RPM speed. Two independent water cooling systems keep temperatures in check for maximum run time.



Injection-Molded ABS Hull
Disruptor’s ABS hull provides the superior strength and rigidity required for high-voltage brushless horsepower without excess weight. The unique injection-molded design features multiple support trusses and ridges for exceptional strength. Molded bosses secure the removable electronics tray in place with minimal hardware for additional weight savings.

Specs:

  • Hull Type: Deep-V
  • Hull Length: 666mm
  • Overall Length: 756mm
  • Width: 194mm
  • Height: 150mm
  • Deadrise: 25 degrees
  • Weight (no battery): 1.66kg
  • Speed Control: VXL-4s™ Marine electronic speed control
  • Motor (electric): 14-pole brushless outrunner
  • Cooling: Independent dual-inlet water cooling
  • Hull Material: Injection-molded ABS
  • Drive System: Direct drive 0.15-inch flex cable
  • Prop: 42mm 2-blade composite (59mm pitch)
  • Outdrive: Anodized aluminum
  • Steering Servo: 2056 waterproof
  • Radio System: TQ™ 2.4 GHz (2-channel)
  • Receiver: 6519 2.4 GHz 3-channel
  • Skill Level: 2
  • Battery Compartment: 180mm long x 49mm wide


Motor Specs:

  • Type: 14-pole brushless outrunner
  • Length: 68mm
  • Diameter: 43mm
  • Motor Shaft: 5mm
  • Motor Connectors: 6.5mm bullet


ESC Specs:

  • Input Voltage (cells): 2-4s LiPo
  • BEC Voltage: 6.0 volts
  • Thermal Protection: Two-stage thermal shutdown
  • Battery Connector: Traxxas High Current Connector


What’s In The Box:

  • Disruptor 4s boat with VXL-4s Marine ESC and outrunner motor
  • Quick Start Guide
  • TQ 2.4 GHz radio system
  • Boat stand
  • Hatch nut tool
  • Maintenance tools
  • Optional hatch wingnuts


What You’ll Need:

  • Batteries: Disruptor requires a 4-cell LiPo battery for maximum performance. 2 and 3-cell LiPo batteries are optional.
  • Charger: Traxxas EZ-Peak® Live (2971) is recommended for easy and fast charging performance.
  • AA Alkaline Batteries: Four AA alkaline batteries for the transmitter.

Produsent

Dette er den beste merket for RC-BIL i hele Norge, nei vi kan vel si hele verden uten å trenge å være redd for at vi sier noe galt!

Reservedeler

Option Parts

Batteri

Servo

Manual

Delekatalog

Disruptor (106064-4) Chassis Assembly Exploded View.            Trykk her!

Disruptor (106064-4) Front Assembly Exploded View.                  Trykk her!

Deleliste

Traxxas alu. deler

Trykk her!

Relaterte produkter

 

Art.nr: TRX 10650
Copied
Traxxas 10650 - Tandem-Axle Boat Trailer Made for Disruptor (78cm long) Transport your Traxxas Disruptor® to the lake in style with this fully detailed scale replica tandem-axle trailer. Elastic tie-downs hold the boat securely to the trailer’s lightweight, full-length aluminum frame. You can even challenge your trailering skills by backing the trailer onto the ramp using your TRX-4® or Traxxas Ford® Raptor R™ with the included variable-height hitches. Boat Trailer Features:­ Elastic tie downs hold the boat securely Variable height hitch Fold-down trailer jack stand Lightweight aluminum frame LED-Ready light lenses Accommodates Pro Scale Winch Variable Height Hitch Included The boat trailer is authentic down to the smallest detail with a folding jack stand, variable-height hitch, and lenses for the optional LED light kit. There’s even a mount to use the Traxxas Pro Scale®Winch to haul your boat out of the water. Optional Winch Accessory (Part 8855, sold separately) Optional LED Light Kit (Part 10349, sold separately)

1.795,-

1.995,-

KJØP
-10%
Art.nr: TRX 106064-4-PINK
Copied
Traxxas TRX106064-4-PINK- Disruptor 4s with Self-Righting - PINK Features: FAST 64+KPH Speed RELIABLE 4s Power 26-INCH Deep-V Stability RAPID RIGHT™ Self-Righting Security RUGGED Construction FULL-THROTTLE, NON-STOP FUN The all-new 4s Disruptor® is the one boat that holds nothing back. Pin the throttle and Disruptor’s deep-V hull launches hard on its way to 64+KPH on a single 4s LiPo battery. At 66cm long, Disruptor is perfectly sized to be quick and agile on small ponds and stable in open water. Disruptor is purpose-built by Traxxas for the wildest stunts and unlimited fun—all with self-righting security. RAPID RIGHT SECURITY There’s no need to back off the throttle or tone down the fun with Disruptor's Rapid Right security. Take full advantage of 4s Velineon® brushless horsepower anytime, anywhere. If Disruptor should land upside down, applying reverse full throttle rights the boat almost instantly and gets you back in the action. AGILE HANDLING Disruptor’s perfectly sized hull delivers agile handling for tight turns with equally impressive 64+KPH speed. A new low-CG design concentrates weight inboard along the centerline for perfect weight distribution. Hammer the throttle and Disruptor gets on plane quickly with lightning-fast reflexes and high-speed stability. NEW 4s POWER SYSTEM The Velineon VXL-4s Marine brushless power system is a clean-slate design optimized to deliver maximum thrust on a single 4s LiPo battery. The all-new brushless outrunner motor is a model of efficiency and power, combining thunderous torque with high-RPM speed. Two independent water cooling systems keep temperatures in check for maximum run time. Injection-Molded ABS Hull Disruptor’s ABS hull provides the superior strength and rigidity required for high-voltage brushless horsepower without excess weight. The unique injection-molded design features multiple support trusses and ridges for exceptional strength. Molded bosses secure the removable electronics tray in place with minimal hardware for additional weight savings. Specs: Hull Type: Deep-V Hull Length: 666mm Overall Length: 756mm Width: 194mm Height: 150mm Deadrise: 25 degrees Weight (no battery): 1.66kg Speed Control: VXL-4s™ Marine electronic speed control Motor (electric): 14-pole brushless outrunner Cooling: Independent dual-inlet water cooling Hull Material: Injection-molded ABS Drive System: Direct drive 0.15-inch flex cable Prop: 42mm 2-blade composite (59mm pitch) Outdrive: Anodized aluminum Steering Servo: 2056 waterproof Radio System: TQ™ 2.4 GHz (2-channel) Receiver: 6519 2.4 GHz 3-channel Skill Level: 2 Battery Compartment: 180mm long x 49mm wide Motor Specs: Type: 14-pole brushless outrunner Length: 68mm Diameter: 43mm Motor Shaft: 5mm Motor Connectors: 6.5mm bullet ESC Specs: Input Voltage (cells): 2-4s LiPo BEC Voltage: 6.0 volts Thermal Protection: Two-stage thermal shutdown Battery Connector: Traxxas High Current Connector What’s In The Box: Disruptor 4s boat with VXL-4s Marine ESC and outrunner motor Quick Start Guide TQ 2.4 GHz radio system Boat stand Hatch nut tool Maintenance tools Optional hatch wingnuts What You’ll Need: Batteries: Disruptor requires a 4-cell LiPo battery for maximum performance. 2 and 3-cell LiPo batteries are optional. Charger: Traxxas EZ-Peak® Live (2971) is recommended for easy and fast charging performance. AA Alkaline Batteries: Four AA alkaline batteries for the transmitter.

4.795,-

5.395,-

KJØP
-11%
Art.nr: TRX 106064-4-GRN
Copied
Traxxas TRX106064-4-GRN- Disruptor 4s with Self-Righting - GREEN Features: FAST 64+KPH Speed RELIABLE 4s Power 26-INCH Deep-V Stability RAPID RIGHT™ Self-Righting Security RUGGED Construction FULL-THROTTLE, NON-STOP FUN The all-new 4s Disruptor® is the one boat that holds nothing back. Pin the throttle and Disruptor’s deep-V hull launches hard on its way to 64+KPH on a single 4s LiPo battery. At 66cm long, Disruptor is perfectly sized to be quick and agile on small ponds and stable in open water. Disruptor is purpose-built by Traxxas for the wildest stunts and unlimited fun—all with self-righting security. RAPID RIGHT SECURITY There’s no need to back off the throttle or tone down the fun with Disruptor's Rapid Right security. Take full advantage of 4s Velineon® brushless horsepower anytime, anywhere. If Disruptor should land upside down, applying reverse full throttle rights the boat almost instantly and gets you back in the action. AGILE HANDLING Disruptor’s perfectly sized hull delivers agile handling for tight turns with equally impressive 64+KPH speed. A new low-CG design concentrates weight inboard along the centerline for perfect weight distribution. Hammer the throttle and Disruptor gets on plane quickly with lightning-fast reflexes and high-speed stability. NEW 4s POWER SYSTEM The Velineon VXL-4s Marine brushless power system is a clean-slate design optimized to deliver maximum thrust on a single 4s LiPo battery. The all-new brushless outrunner motor is a model of efficiency and power, combining thunderous torque with high-RPM speed. Two independent water cooling systems keep temperatures in check for maximum run time. Injection-Molded ABS Hull Disruptor’s ABS hull provides the superior strength and rigidity required for high-voltage brushless horsepower without excess weight. The unique injection-molded design features multiple support trusses and ridges for exceptional strength. Molded bosses secure the removable electronics tray in place with minimal hardware for additional weight savings. Specs: Hull Type: Deep-V Hull Length: 666mm Overall Length: 756mm Width: 194mm Height: 150mm Deadrise: 25 degrees Weight (no battery): 1.66kg Speed Control: VXL-4s™ Marine electronic speed control Motor (electric): 14-pole brushless outrunner Cooling: Independent dual-inlet water cooling Hull Material: Injection-molded ABS Drive System: Direct drive 0.15-inch flex cable Prop: 42mm 2-blade composite (59mm pitch) Outdrive: Anodized aluminum Steering Servo: 2056 waterproof Radio System: TQ™ 2.4 GHz (2-channel) Receiver: 6519 2.4 GHz 3-channel Skill Level: 2 Battery Compartment: 180mm long x 49mm wide Motor Specs: Type: 14-pole brushless outrunner Length: 68mm Diameter: 43mm Motor Shaft: 5mm Motor Connectors: 6.5mm bullet ESC Specs: Input Voltage (cells): 2-4s LiPo BEC Voltage: 6.0 volts Thermal Protection: Two-stage thermal shutdown Battery Connector: Traxxas High Current Connector What’s In The Box: Disruptor 4s boat with VXL-4s Marine ESC and outrunner motor Quick Start Guide TQ 2.4 GHz radio system Boat stand Hatch nut tool Maintenance tools Optional hatch wingnuts What You’ll Need: Batteries: Disruptor requires a 4-cell LiPo battery for maximum performance. 2 and 3-cell LiPo batteries are optional. Charger: Traxxas EZ-Peak® Live (2971) is recommended for easy and fast charging performance. AA Alkaline Batteries: Four AA alkaline batteries for the transmitter.

4.795,-

5.395,-

KJØP
-11%
Art.nr: TRX 106064-4-ORNG
Copied
Traxxas TRX106064-4-ORNG- Disruptor 4s with Self-Righting - ORANGE Features: FAST 64+KPH Speed RELIABLE 4s Power 26-INCH Deep-V Stability RAPID RIGHT™ Self-Righting Security RUGGED Construction FULL-THROTTLE, NON-STOP FUN The all-new 4s Disruptor® is the one boat that holds nothing back. Pin the throttle and Disruptor’s deep-V hull launches hard on its way to 64+KPH on a single 4s LiPo battery. At 66cm long, Disruptor is perfectly sized to be quick and agile on small ponds and stable in open water. Disruptor is purpose-built by Traxxas for the wildest stunts and unlimited fun—all with self-righting security. RAPID RIGHT SECURITY There’s no need to back off the throttle or tone down the fun with Disruptor's Rapid Right security. Take full advantage of 4s Velineon® brushless horsepower anytime, anywhere. If Disruptor should land upside down, applying reverse full throttle rights the boat almost instantly and gets you back in the action. AGILE HANDLING Disruptor’s perfectly sized hull delivers agile handling for tight turns with equally impressive 64+KPH speed. A new low-CG design concentrates weight inboard along the centerline for perfect weight distribution. Hammer the throttle and Disruptor gets on plane quickly with lightning-fast reflexes and high-speed stability. NEW 4s POWER SYSTEM The Velineon VXL-4s Marine brushless power system is a clean-slate design optimized to deliver maximum thrust on a single 4s LiPo battery. The all-new brushless outrunner motor is a model of efficiency and power, combining thunderous torque with high-RPM speed. Two independent water cooling systems keep temperatures in check for maximum run time. Injection-Molded ABS Hull Disruptor’s ABS hull provides the superior strength and rigidity required for high-voltage brushless horsepower without excess weight. The unique injection-molded design features multiple support trusses and ridges for exceptional strength. Molded bosses secure the removable electronics tray in place with minimal hardware for additional weight savings. Specs: Hull Type: Deep-V Hull Length: 666mm Overall Length: 756mm Width: 194mm Height: 150mm Deadrise: 25 degrees Weight (no battery): 1.66kg Speed Control: VXL-4s™ Marine electronic speed control Motor (electric): 14-pole brushless outrunner Cooling: Independent dual-inlet water cooling Hull Material: Injection-molded ABS Drive System: Direct drive 0.15-inch flex cable Prop: 42mm 2-blade composite (59mm pitch) Outdrive: Anodized aluminum Steering Servo: 2056 waterproof Radio System: TQ™ 2.4 GHz (2-channel) Receiver: 6519 2.4 GHz 3-channel Skill Level: 2 Battery Compartment: 180mm long x 49mm wide Motor Specs: Type: 14-pole brushless outrunner Length: 68mm Diameter: 43mm Motor Shaft: 5mm Motor Connectors: 6.5mm bullet ESC Specs: Input Voltage (cells): 2-4s LiPo BEC Voltage: 6.0 volts Thermal Protection: Two-stage thermal shutdown Battery Connector: Traxxas High Current Connector What’s In The Box: Disruptor 4s boat with VXL-4s Marine ESC and outrunner motor Quick Start Guide TQ 2.4 GHz radio system Boat stand Hatch nut tool Maintenance tools Optional hatch wingnuts What You’ll Need: Batteries: Disruptor requires a 4-cell LiPo battery for maximum performance. 2 and 3-cell LiPo batteries are optional. Charger: Traxxas EZ-Peak® Live (2971) is recommended for easy and fast charging performance. AA Alkaline Batteries: Four AA alkaline batteries for the transmitter.

4.795,-

5.395,-

KJØP
-11%

Kunder kjøpte også

Spur Gear 50T Steel Wide + Pinion Gear 20T 1.0M Set Spur gear, 50-tooth (machined, hardened steel) (wide-face)/ gear, 20-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw The 50-tooth spur gear and 20-tooth pinion gear combo (1.0 metric pitch) is machined from solid steel with extra-wide steel teeth for ultimate power handling and durability. Traxxas spur gears let you fine-tune the performance of your Traxxas model. Changing gear ratios can help balance acceleration and top speed for different running conditions. Please consult your owner’s manual for more information on recommended gearing options for your specific model. Accessory part for these models: XRT

499,-

629,-

KJØP
-21%
This is the 1/14 scale Tamiya 40' Container Kit.          The Tractor Truck and Trailer with Wheels are NOT Included. FEATURES: Connects to any Tamiya 1/14 scale tractor truck           White plastic side panels           Container can be detached after assembly           Rear gate doors open with realistic latches and hinges           Aluminum frame, coupler plate, gate and other metal components INCLUDES: Decal Sheet ("Maersk", license plates, numbers, load specs, "Tamiya")           Container Kit           Illustrated Instructions SPECS:    Length:        34.4" (874mm)           Width:         7.09" (180mm)           Height:        7.28" (185mm) REQUIRES: Paint and building equipment

2.495,-

2.695,-

Ikke på lager
-7%
TAMIYA RC THUNDER DRAGON (2021) This is a re-issue of the classic Thunder Dragon buggy originally released in 1988. The classic buggy utilizes shaft-driven 4WD and smooth, ground hugging suspension providing a super-fun driving experience. The stylish Thunder Dragon body which appeared in a classic R/C comic in Japan, is an exciting re-release for R/C fans of all ages and abilities. • 1/10 scale R/C model assembly kit. Length: 390mm, width: 240mm, height: 130mm. Wheelbase: 260mm. • The chassis is based around an ABS plastic bathtub frame for excellent durability and ease of maintenance. • 4-wheel double wishbone suspension uses CVA oil shock-dampers and a front stabilizer for a superior ride. • Features shaft-driven 4WD with front and rear die-cast 3-bevel differentials for smooth, superior handling feel. • Semi-pneumatic spike tires give great grip, and are paired with large-diameter ABS wheels. • Thunder Dragon body is molded in polycarbonate, with non-canopy sections pre-painted in silver. It is pre-cut for convenience. • Includes NEW TBLE-04S ESC. Compatible with brushless motors (sensored) of 21.5 turns and higher, and Tamiya brushed motors 25 turns and over. • Includes 540 brushed type motor. Requires: 2-channel radio Steering servo 7.2-7.4volt battery pack and compatible charger. SPECIFICATIONS Adjustable Gear Ratio Fixed Bearings Plastic bushing Body Material Polycarbonate Body Stickers Included Chassis Material ABS Plastic Construction Type Assembly Kit Differential Type Gear Drive Type 4WD Electronic Speed Control (esc) Includes NEW TBLE-04S ESC. Compatible with brushless motors (sensored) of 21.5 turns and higher, and Tamiya brushed motors 25 turns and over. Motor 540-brushed type Requires A 2-channel radio, steering servo, 7.2volt battery & battery charger, and Tamiya PS paint. Scale 1/10 Shock Damper CVA Oil Filled Suspension 4-wheel fully independent double wishbone Terrain Use Off-Road

2.495,-

2.795,-

KJØP
-11%
TAMIYA RC SUPER AVANTE Required To Complete  2-channel radio, Low profile steering servo, ESC, Motor, 7.2-7.4volt battery & battery charger, and Tamiya PS paint. A Super New Face This R/C model assembly kit creates the Super Avante, a 4WD off-road buggy that is bestowed with Tamiya’s legendary Avante name. It features an exceptionally low profile design enabled in part by its front inboard suspension, with a shaft-driven 4WD drivetrain powered by a midship motor and employing front/rear ball differentials plus full ball bearings. Its futuristic body design is the work of Kota Nezu at znug design, and features numerous clear sections that just add to the Super Avante’s distinctly modern mood, as do the cockpit-rear buttress and the four mini fenders.   ★Take a separate look at the pioneering, futuristic design (the work of Kota Nezu at znug design) from the rear of the model, too!   ★Seen from the side, one can appreciate just how lowdown this streamlined buggy gets, with an accent provided by the fenders.   ★This is a close-up on the driver figure included in the kit, who is ready to take the wheel and give your buggy a realistic look.   ★A further glance inside the cockpit shows stickers for display elements. Clear parts are used in three other locations across the car.   ★All four wheels have an individual mini-fender; they are both practical (helping to block flying debris) and provide a unique design element.   ★Buttresses are a trendy aerodynamic item at present, and the Super Avante is endowed with its own polycarbonate design, a separate part.       ★Left: Two different wing stay designs (high and low) are included in the kit, to help you tweak the car’s downforce. ★Right: Vibrant yellow star dish design wheels are paired with high grip square spike tires for superior off-roading.   TD4 – Low Profile, High Performance The TD4 is a shaft-driven 4WD buggy chassis which employs front inboard suspension for slim, low-profile form. It features a longitudinal battery pack position in the center and a midship transverse motor for optimum balance and improved performance. The drivetrain uses full bearings, and sealed front/rear gearboxes have built-in ball differentials. Two link rods and crank arm transmit movement of the left-side servo to the three-piece steering arm setup. 4-wheel independent double wishbone suspension utilizes CVA oil dampers. Turnbuckle shaft upper arms facilitate camber angle adjustment. Two types (high/low) of wing stays are included and star dish wheels are paired with square spike tires which offer superlative grip off-road.   ★The shaft-driven 4WD chassis makes a major contribution to the model’s low profile, and is a highly slimline deisgn to boot.   ★Take a closer look at the front double-wishbone setup with lower “H” arms, and turnbuckle upper arms that allow easy camber tweaks.   ★Rocker arms and push-rods are used to actuate the front inboard CVA oil dampers, which are near-horizontal (10 degrees) in their position.   ★The TD4 chassis has its motor in a midship position, and ducts are worked into the design to ensure that it is cooled as much as possible.   ★This picture is a close-up on the TD4’s propeller shaft, which runs along the side of the chassis to provide the front wheels with power.   ★Both front and rear gearboxes are sealed, and contain one of these – a ball differential. Steel joints contribute to the model’s durability.       ★Left: Like the front, the rear double wishbone suspension utilizes upper turnbuckle shaft and rear “H” arms. ★Right: Access to the battery pack is provided by the front suspension, which springs up dynamically.   Specifications Length: 387mm, width: 246mm, height: 117mm (with low wing stays employed) Wheelbase: 283mm  Tread: 214mm (front), 205mm (rear) Plastic bathtub frame Shaft-driven 4WD Front & rear ball differentials 3-piece steering tie-rod 4- wheel double wishbone suspension Tire width/diameter: 32/82mm (front), 41/82mm (rear) CVA oil dampers ★Gear Ratio = 10.71:1 Type 540 motor Electronic Speed Controller (ESC) is sold separately.   Separately Required Items 2-channel R/C system w/ESC R6/AA/UM3 batteries for transmitter Battery pack & charger

4.295,-

4.595,-

KJØP
-7%
TAMIYA RC AVANTE 2011 BLACK SPECIAL This is a Limited-Edition Black Special release of the Avante 2011 edition, which was originally released to commemorate the 35th anniversary of Tamiya R/C car products. It sports a color scheme inspired by its Mini 4WD cousin the Avante Black Special. About the Avante: The machine features a unique shaft-driven 4WD system which was taken from Tamiya’s first 4WD R/C buggy, the Hotshot. It features a highly sophisticated design including an FRP double-deck chassis layout, longitudinal motor & battery positions, and a formula-type body with chassis fairing. It is equipped with innovative components such as a compact gearbox with 3 small planetary gears, a center diff to increase stability, a fully adjustable suspension, and cam-lock wheel caps. The modern specification of the car has a few updates, such as universal drive-shafts and machined aluminum uprights, which gives this version increased durability and performance over the original. • 1/10 scale R/C shaft-driven 4WD buggy assembly kit. Length: 420mm, width: 240mm, height: 140mm. Wheelbase: 260mm. • Carbon-fiber parts such as 2mm thickness upper & lower decks, plus rear damper stay offer superb strength. • Includes Avante (2011) Racing Steering Set, with a 2mm thickness carbon fiber steering plate and 850 ball bearings giving silky smooth motion. • Includes Avante (2011) Torque Splitter Set, with torque splitter and ball differentials for sure-footed traction. • 4-wheel double wishbone suspension has metal shafts for great customizability. • Aluminum front uprights. • Spike tires are mounted on fluorescent pink wheels. • Comes with a 25-Turn motor featuring a special label.  Requires: 2-Channel Radio servo ESC (electronic speed control) 7.2volt battery pack & charger Tamiya PS paint. Specs: Adjustable Gear Ratio Yes Bearings Includes full ball bearings Body Material Polycarbonate Body Stickers Included Chassis Material Carbon fiber plate Construction Type Assembly Kit Differential Type Gear Drive Type 4WD Motor Brushed 540 Type Required To Complete Requires: 2-Channel Radio, servo, ESC (electronic speed control) 7.2volt battery pack & charger, and Tamiya PS paint. Scale 1/10 Shock Damper Oil-filled damper Suspension 4-wheel fully independent double wishbone Terrain Use Off-Road

5.995,-

6.595,-

KJØP
-9%
Tamiya 58697 Astute 2022 (TD2) 2WD Kit 1:10   Tamiya brings yet another off-road buggy to its vast library of high-performance and fun to build R/C kits. This is the Astute 2022, which is based on the new TD2 chassis. TD2 chassis at a glance: The new TD2 chassis is based around the TD4 chassis. Just like the TD4 machine, it employs a front inboard suspension layout which offers exceptionally slim, low-profile form. Its front suspension arms have a skid angle of 25 degrees, for amazing ground-hugging and stable performance, plus CVA oil dampers to allow smooth suspension movement. Furthermore, the chassis is based on a one-piece monocoque frame, uses the same ball differential as the ones used on the TD4 chassis, plus full ball bearings are used throughout the driveline. The battery pack is positioned transversely and positioned to the rear. Finally, a midship transverse motor layout with 3 gears connecting it to the drivetrain provide optimum balance and improved performance. FEATURES: 1/10 R/C assembly kit. Length: 387mm, width: 246mm. Wheelbase: 283mm. Polycarbonate body. Ribbed front and rear square spike tires facilitate stability and great grip. Newly designed star dish design front wheels are attached by hex hubs. 4-wheel double wishbone suspension system uses CVA oil dampers for supple performance. Choose between high and low type wing stays to adjust the downforce set up of the buggy. Driver figure included for extra realism. REQUIRES: 2-channel radio steering servo ESC 540-size motor 7.2-7.4volt battery with compatible charger Tamiya PS paint to complete Morsom byggevideo:      

3.195,-

3.995,-

KJØP
-20%
ay Out Style! This assembly kit creates a special Black Edition of the legendary Egress R/C buggy, which originally took the world by storm after its 1989 debut, and was then given a further update in 2013. As the name implies, its color scheme is distinctly black-based, with dampers and front uprights switched to dark titanium anodized finishes, and the six-spoke wheels molded in silver to match a body to be painted black.   Shaft-driven 4WD chassis with carbon components This shaft-driven 4WD chassis features a longitudinally-positioned motor and full ball bearings, while carbon fiber upper and lower decks ensure that the model has superb rigidity. Front and rear ball differentials offer excellent reliability and easy maintenance, working in tandem with the built-in center one-way to provide sure-footed movement, and the one-way can be locked if desired. Universal drive shafts feature the same design as those used in TRF series parts, in order to maximize transmission efficiency and minimize wear and tear. 4-wheel double wishbone suspension is supported by four oil dampers equipped with aluminum cylinders, while the front and rear of the model are fitted with stabilizers. Aluminum front uprights offer excellent reliability, and ball bearings in steering linkage arms combine with 2mm thick carbon fiber plate to offer a linear steering response. The Egress also features a brushless motor.   ★The three-piece steering tie-rod has a 2mm carbon fiber plate that helps to keep handling sharp and crisp.   ★Dark titanium anodized uprights and oil damper parts are employed along with efficient universal shafts.   ★Silver color 6-spoke wheels are paired with high-performance hybrid spike tires for a super drive.   ★Lightweight carbon fiber is employed for the 2mm-thickness decks in the rigid double-deck frame.   ★The model uses a midship motor position with one-way bearing on the gear for linear handling feel. *Motor is sold separately.   ★This image shows the rear suspension, which also uses efficient universal drive shafts.       ★Left: Take a closer look at the combination of high-capacity oil dampers and carbon fiber stay. ★Right: Mirrored stickers such as the rear wing slogan give the model that finishing touch.   Specifications ★Length: 430mm, width: 243mm, height: 157mm ★Wheelbase: 275mm ★Tire width/diameter: 32/88mm (front), 40/88mm (rear) ★2mm carbon fiber double deck frame ★Longitudinally-placed motor, shaft-driven 4WD ★Polycarbonate body and undertray ★Front & rear ball diffferentials, center one-way ★3-piece steering tie-rod ★4-wheel independent double-wishbone suspension ★High-capacity oil dampers with aluminum cylinders ★Gear ratio = 8.33:1 ★Type 540 motor and electronic speed controller (ESC) are sold separately.   Separately Required Items ★Type 540 motor ★2-channel R/C system w/ESC ★R6/AA/UM3 batteries for transmitter ★Battery pack & charger

6.195,-

6.795,-

KJØP
-9%
The TT-02 Type-SRX chassis kit is an upgraded version of the TT-02 Type-S Series with enhanced durability and performance for racing. This chassis kit uses Items 22049 and 22047 with updated parts. Also, parts included in this chassis kit were chosen for users who want to learn setup before levelling up to mid-level Tamiya chassis kits. (More cost-effective than buying each part separately) Included Hop-up Option Parts Item 22054: 37mm Drive Shafts for Double Cardan Joint Shafts (2pcs.) Item 22049: XV-02/TT-02 Oil Gear Differential Unit Item 22047: XV-02/TT-02 Front Direct Coupling Set (39T) Item 54981: 06 Module Hard Coated Aluminum Pinion Gear (27T) Item 54886: TRF419 Suspension Upgrade Set Item 54799: TT-02 Hi-Torque Servo Saver Set (w/Aluminum Horn) Item 54501: TT-02 Aluminum Propeller Shaft Item 54500: TT-02 High Speed Gear Set (68T) Item 53823: Clamp Type Aluminum Wheel Hub (5mm Thick) Item 53576: TRF Damper Oil Seal (4pcs.) Item 42357: Cross Joints for Low Friction Assembly Universal Shafts Item 42323: Short Ball Connector Nuts for TRF Dampers (8pcs.) Item 42143: 4mm Aluminum Serrated Wheel Nut (4pcs. /Blue) • 1/10 scale R/C chassis assembly kit. • The rear oil-filled diff gear unit and front direct spool ensure ease of assembly and stable drivability. • Diff. joint cups are lightweight aluminum and give a weight reduction of 7.8g compared to Item 22049’s standard ones. • Direct cups are designed for this chassis kit for improved durability. • This chassis kit features dependable 4-wheel independent double wishbone suspension from Item 42345 (1/10 R/C TRF420 Chassis Kit) for effective setup options. • Newly shaped propeller joints are compatible with swing shaft protectors. These parts use plastic parts at joint sections with stainless pins and aluminum joints to limit wear of parts. • Uses Item 22054 37mm Drive Shafts which allows stable steering and cornering for superior performance at races. • Rear drive shafts are 39mm size which are specific for this chassis. These also have a hard coat to enhance durability and lubricity. • High speed gears and 27T pinion gears (gear ratio: 6.55: 1) are included as the kit-standard parts. • Included TT-02 hi-torque servo saver allows steering angle limit to prevent damage of steering servo. • Includes full ball bearings. • Comes with a carrying case dedicated for the TT-02 Type-SRX chassis. • Required to complete: 2-channel radio, steering servo, ESC, motor, 7.2-7.4volt battery with compatible charger, body, and tires.

3.695,-

4.595,-

KJØP
-20%
8714 1/10 RC Golf Mk2 GTi (A2 Rally) (MF-01X) The 1980’s was the decade of the hot hatch back in automotive circles! One of the many automakers that made hatchbacks popular was Volkswagen, and their MK2 GTI 16V was a favorite among automotive fans. Tamiya has faithfully recreated the MK2 GTI as a rally race car as seen in A7 class competition. The body is based on the MF-01 chassis as it’s at home on both asphalt and flat dirt running! 【MF-01X – Compact 4WD At Home on a Range of Surfaces】 Based around a tough monocoque frame with integrated gearboxes, this compact 4WD chassis gives a thrilling drive whether you take it on road or flat dirt surfaces. It features a rear-mounted motor, with gear-driven rear wheels and a propeller shaft taking power to the front. Both front and rear gearboxes have differential gears. The battery pack location in the chassis center secures excellent balance, while 4-wheel independent double wishbone suspension employs friction dampers. 【Special Features】 1/10 scale R/C model assembly kit. Length: 397mm, width: 170mm, height: 142mm. Wheelbase: 239mm (L-size wheelbase spec). Lightweight polycarbonate body. Separately molded plastic components recreate light cases, bumper, and side mirrors. The MF-01X chassis is at home on-road or on flat dirt, thanks to 4-wheel double wishbone suspension. Polycarbonate light cases are compatible with separately sold 5mm LEDs. Stickers are included to recreate body details. A host of Hop-Up Option parts are available to tune the MF-01X chassis. Includes 540 Torque Tuned motor. Requires 2-channel radio, steering servo, ESC, 7.2volt battery with compatible charger and Tamiya PS paint to complete.

1.995,-

2.295,-

KJØP
-13%
AMS & CMS 1/10 Kit God vekt distribusjon Axial SCX10 Pro vil for mange bli førstevalget når det kommer til å bygge seg en custom crawler, formidabel fremkommelighet, et bredt utvalg av tuning, oppgraderingsutstyr og tilbehør. Her leverer Axial den perfekte plattformen til et slik prosjekt, et minimalistisk SCX10 Pro kit hvor man kan supplerer med foretrukken elektronikk, hjul og karosseri. PS! Produkt kan avvike fra video. Klippet er lagt til som relevant opplysning til produktet, men er ikke nødvendigvis identisk. Innhold i en produktvideo, testvideo eller et review kan avvike fra produktet som selges. Dette kan gjelde farger, spesifikasjoner, versjonsforskjeller, regionsforskjeller m.m. Det er produktets navn, beskrivelse og bilder du skal forholde deg til ved kjøp av varen.   Comp Optimized Chassis Lettere, lavere og svært justerbar, SCX10 Pro 4WD-aluchassiset er optimalisert for comp-verdig crawling, sidehilling og break over. 3-link/4-link fjæring, nye oljefylte alu støtdempere og komplette kulelagre. Muliti-Piece Axles w/Steel Tubes Aksler i flere deler med stålrør kan romme en akselmontert servo (AMS) eller en chassismontert servo (CMS) for å gi den en enda bedre skala-look Forward Motor Mounting Motorfestet plasserer ditt valg av motor lavt og fremover i chassiset for overlegen vektfordeling, og gir balansen som trengs for å unngå å snu mens du prøver deg på vanskelige linjer. Shift-Able Underdrive Transmission Med SCX10 Pro sin gir-overføring vil du få 40% underdrive i bakaksel manuelt eller med servo. Under kjøring gir bakakselen en tightere svingradius og reduserer "torque twist" ved stigninger. Alu Body Shocks Ved å eliminere støtfjæren og "kragen" fra utsiden av støtdemperkroppen, gir den glatte oljefyltaluminium-shocken støtdemperne høyere klaring når du drar nytte av SCX10 Pros økte styrevinkel. Dempernes "eye to eye" lengde er 96 mm og bruker 12 mm diameter fjærer. Den doble O-ringens nedre støtdeksel fungerer som den øvre fjærholderen, mens den nedre støtdemperkoppen har en innebygd støtstopp som kan trimmes for å finjustere fjæringen.   Nødvendig tilbehør Radio og mottaker ESC Motor Styreservo Dekk og felg Batteri Lader Karosseri Verktøy, lim og lakk Dimensjoner Bakkeklaring: 57.1mm Høyde: 178mm Lengde: 423mm Bredde: 235mm Vekt: 1.4kg (uten komponenter) Skala: 1/10 Hjulbase: 318mm Hex: 12mm Styring: 2WS      

6.895,-

6.995,-

KJØP
-1%
Kyosho Starter Set 1:10 BLS 2WD (KT331-37031-37051B-82274)

3.995,-

4.195,-

KJØP
-5%
Super Avante ferdiglakkert i metallic blå og gul. Kommer som kit. OBS: Trenger low profile servo!   Fra produsenten: Special Super Avante This assembly kit creates a special version of the stylish Super Avante 4WD R/C buggy, the (znug design) Kota Nezu-designed polycarbonate body pre-painted in metallic blue and yellow, and pre-cut for convenience. Its fenders are likewise pre-cut and pre-painted in metallic blue, just requiring application of yellow stickers, while the rear wing is also already cut. A further splash of color is provided by yellow main frame and damper spring components.   TD4 – Low Profile, High Performance The TD4 is a shaft-driven 4WD buggy chassis which employs front inboard suspension for slim, low-profile form. It features a longitudinal battery pack position in the center and a midship transverse motor for optimum balance and improved performance. The drivetrain uses full bearings, and sealed front/rear gearboxes have built-in ball differentials. Two link rods and crank arm transmit movement of the left-side servo to the three-piece steering arm setup. 4-wheel independent double wishbone suspension utilizes CVA oil dampers. Turnbuckle shaft upper arms facilitate camber angle adjustment. Two types (high/low) of wing stays are included and star dish wheels are paired with square spike tires which offer superlative grip off-road.       ★Left: The slim, low profile form is striking. On this model, the main frame is molded in yellow plastic. ★Right: Front CVA oil dampers feature yellow springs, visible through the windows on the cockpit sides.       ★Left: Rear CVA oil dampers also have yellow springs, adding a further splash of color to this buggy. ★Right: The rear wing comes pre-cut for convenience. Choose between low and high stays (image shows low).   Specifications ★Length: 387mm, width: 246mm, height: 117mm (with low wing stays employed) ★Wheelbase: 283mm ★Tread: 214mm (front), 205mm (rear) ★Plastic bathtub frame ★Shaft-driven 4WD ★Front & rear ball differentials ★3-piece steering tie-rod ★4- wheel double wishbone suspension ★Tire width/diameter: 32/82mm (front), 41/82mm (rear) ★CVA oil dampers ★Gear ratio = 10.71:1 ★Full ball bearings ★Type 540 motor & Electronic Speed Controller (ESC) sold separately.   Separately Required Items ★Type 540 motor ★2-channel R/C system w/ESC ★R6/AA/UM3 batteries for transmitter ★Battery pack & charger

4.695,-

4.995,-

KJØP
-6%
Latest high-performance MR-04 chassis Now the standard MINI-Z RWD model! Enjoy the full experience of high-performance R/C car racing right out of the box; just insert batteries into the car and transmitter. This is the simplicity of Kyosho Readyset packages. The small scale of the MINI-Z Racer is ideal for driving indoors and for people just becoming familiar with R/C cars. This MINI-Z RWD Readyset includes a renewed 2-wheel drive chassis at its core. Previous Readyset packages incorporated the 3rd generation MR-03 chassis, but the new RWD Readyset includes the 4th generation MR-04 chassis that was first released in 2023. While retaining some basic elements of the MR-03 design, the new MR-04 demonstrated its lower center of gravity and remodeled steering design with blistering speed and excellent handling in the top-of-the-line EVO2 debut model. The MR-04 chassis is mounted with R/C system and features a completed body finished to display model standard. This Readyset includes the same standard MR-04 chassis as other high-end MR-04 models and includes user-friendly 130-class brushed motor and the reliable Syncro KT-531P pistol grip transmitter. Just insert 4 x AAA alkaline batteries into both the car and the transmitter, and you’re ready for the fun to begin. High-performance comes straight from the standard setup, but you can tune up for elite-level performance with a wide range of MINI-Z optional parts. With its dynamic maneuverability display model finish, the updated MR-04 chassis takes the authentic R/C experience to a higher level. - Authentic EP (electric) small scale R/C car that can be driven indoors. - Readyset package includes fully assembled chassis, body and transmitter. - Includes ultra reliable multi-function Syncro KT-531P transmitter. - Features the MR-04 chassis, a major evolution from the previous MR-03 model. - Includes high-quality painted body with decals applied, finished to display model standard. - Geared differential (gear diff) delivers smooth cornering. - Full ball bearing specifications - Can be fitted with an optional gyro unit (MZW711) for even easier control. Gyro sensitivity can be adjusted using the volume on the chassis. - Compatible with wide range of MINI-Z Racer optional parts so you can enjoy tuning and enhancing your model.     While retaining the best aspects of the MR-03, the lower center of gravity of the new MR-04 delivers significant performance improvements. The easier control of the MR-04 makes it an ideal introduction to R/C cars.     New front knuckles with integrated kingpins reduce scrub by 1.5mm on each side compared to the MR-03, realizing sharper and more linear control. The change to 3mm inner diameter ball bearings also reduces rotational resistance.     Front suspension dynamically aligns the camber angle with movement of the upper arm to maintain optimal tire contact during cornering. Revised caster angle also delivers improved steering response.     The car is powered by four AAA alkaline or rechargeable nickel-metal hydride batteries. The batteries are mounted lower than the MR-03, lowering the center of gravity of the entire chassis to deliver improved cornering stability and straight-line handling.     The rear suspension uses a coil spring damper to cushion shocks from the road surface and improve driving stability. It can also be upgraded to an optional oil-filled shock absorber.     Flexibility of the T-bar rear suspension plate that holds the entire rear pod, including the motor and rear axle, produces excellent suspension effect. Optional parts are also available in FRP and carbon.     In 2025, All axles are equipped with low rotational resistance ball bearings as standard. The same size ball bearings are used for both front and rear for spare parts efficiency.     When changing from the standard body, a parts set is included to change the front tread (vehicle width) to match the non-standard body to be installed. Rear tread can be changed by changing the wheel offset.     Includes Syncro KT-531P transmitter with a steering wheel that mimics the steering wheel of a real car and pistol-grip throttle (speed control). Adjust the neutral position of steering and throttle with trims, as well as steering angle with dual rate adjustment. It is also possible to operate in training mode with a reduced vehicle speed (training mode is the default setting).

2.495,-

3.295,-

KJØP
-24%
Latest high-performance MR-04 chassis Now the standard MINI-Z RWD model! Enjoy the full experience of high-performance R/C car racing right out of the box; just insert batteries into the car and transmitter. This is the simplicity of Kyosho Readyset packages. The small scale of the MINI-Z Racer is ideal for driving indoors and for people just becoming familiar with R/C cars. This MINI-Z RWD Readyset includes a renewed 2-wheel drive chassis at its core. Previous Readyset packages incorporated the 3rd generation MR-03 chassis, but the new RWD Readyset includes the 4th generation MR-04 chassis that was first released in 2023. While retaining some basic elements of the MR-03 design, the new MR-04 demonstrated its lower center of gravity and remodeled steering design with blistering speed and excellent handling in the top-of-the-line EVO2 debut model. The MR-04 chassis is mounted with R/C system and features a completed body finished to display model standard. This Readyset includes the same standard MR-04 chassis as other high-end MR-04 models and includes user-friendly 130-class brushed motor and the reliable Syncro KT-531P pistol grip transmitter. Just insert 4 x AAA alkaline batteries into both the car and the transmitter, and you’re ready for the fun to begin. High-performance comes straight from the standard setup, but you can tune up for elite-level performance with a wide range of MINI-Z optional parts. With its dynamic maneuverability display model finish, the updated MR-04 chassis takes the authentic R/C experience to a higher level. - Authentic EP (electric) small scale R/C car that can be driven indoors. - Readyset package includes fully assembled chassis, body and transmitter. - Includes ultra reliable multi-function Syncro KT-531P transmitter. - Features the MR-04 chassis, a major evolution from the previous MR-03 model. - Includes high-quality painted body with decals applied, finished to display model standard. - Geared differential (gear diff) delivers smooth cornering. - Full ball bearing specifications - Can be fitted with an optional gyro unit (MZW711) for even easier control. Gyro sensitivity can be adjusted using the volume on the chassis. - Compatible with wide range of MINI-Z Racer optional parts so you can enjoy tuning and enhancing your model.     While retaining the best aspects of the MR-03, the lower center of gravity of the new MR-04 delivers significant performance improvements. The easier control of the MR-04 makes it an ideal introduction to R/C cars.     New front knuckles with integrated kingpins reduce scrub by 1.5mm on each side compared to the MR-03, realizing sharper and more linear control. The change to 3mm inner diameter ball bearings also reduces rotational resistance.     Front suspension dynamically aligns the camber angle with movement of the upper arm to maintain optimal tire contact during cornering. Revised caster angle also delivers improved steering response.     The car is powered by four AAA alkaline or rechargeable nickel-metal hydride batteries. The batteries are mounted lower than the MR-03, lowering the center of gravity of the entire chassis to deliver improved cornering stability and straight-line handling.     The rear suspension uses a coil spring damper to cushion shocks from the road surface and improve driving stability. It can also be upgraded to an optional oil-filled shock absorber.     Flexibility of the T-bar rear suspension plate that holds the entire rear pod, including the motor and rear axle, produces excellent suspension effect. Optional parts are also available in FRP and carbon.     In 2025, All axles are equipped with low rotational resistance ball bearings as standard. The same size ball bearings are used for both front and rear for spare parts efficiency.     When changing from the standard body, a parts set is included to change the front tread (vehicle width) to match the non-standard body to be installed. Rear tread can be changed by changing the wheel offset.     Includes Syncro KT-531P transmitter with a steering wheel that mimics the steering wheel of a real car and pistol-grip throttle (speed control). Adjust the neutral position of steering and throttle with trims, as well as steering angle with dual rate adjustment. It is also possible to operate in training mode with a reduced vehicle speed (training mode is the default setting).

2.995,-

3.295,-

KJØP
-9%
Black Horse | VIPER JET TURBINE | BH181 Following the enormous success of their EDF Viper Jet, Black Horse have introduced this factory built, all-balsa and ply turbine powered version. Supplied pre-built and covered in film, this ARTF model is perfect for 80N class turbines and comes complete with electric retracts and controller. SPECIFICATIONS: Wingspan: 2000 mm Length: 1820 mm Weight: 9.8 – 10.5 kg Wing area: 62.2 dm2 Wing loading: 157.5 g/dm2 Wing type: Naca Airfoil Gear type: Electric Retract Gear (included) with controller box (included) Parts listing required (not included): Radio: 8 channels minimum Servo: 8 servos, size: (35 x 15mm) Engine: Turbine Jet Engine with thrust 8kg Thrust (not included)

13.595,-

14.995,-

KJØP
-9%
Traxxas 10650 - Tandem-Axle Boat Trailer Made for Disruptor (78cm long) Transport your Traxxas Disruptor® to the lake in style with this fully detailed scale replica tandem-axle trailer. Elastic tie-downs hold the boat securely to the trailer’s lightweight, full-length aluminum frame. You can even challenge your trailering skills by backing the trailer onto the ramp using your TRX-4® or Traxxas Ford® Raptor R™ with the included variable-height hitches. Boat Trailer Features:­ Elastic tie downs hold the boat securely Variable height hitch Fold-down trailer jack stand Lightweight aluminum frame LED-Ready light lenses Accommodates Pro Scale Winch Variable Height Hitch Included The boat trailer is authentic down to the smallest detail with a folding jack stand, variable-height hitch, and lenses for the optional LED light kit. There’s even a mount to use the Traxxas Pro Scale®Winch to haul your boat out of the water. Optional Winch Accessory (Part 8855, sold separately) Optional LED Light Kit (Part 10349, sold separately)

1.795,-

1.995,-

KJØP
-10%
  • klarna-dark.png
  • vipps-orange.png
  • mastercard-full.png
  • visa.png
  • paypal.png