Hopp til innhold

Traxxas 7059 Ball Link Set (8)

Art.nr: TRX 7059

49,-

Traxxas

Traxxas

På lager: 3

Produktet er midlertidig utsolgt. Dersom du ønsker å motta en epost når vi får det inn på lager, kan du legge igjen epostadressen din i skjemaet under.

Informasjon

Rod ends (8)/ hollow balls (8)

Produsent

Dette er den beste merket for RC-BIL i hele Norge, nei vi kan vel si hele verden uten å trenge å være redd for at vi sier noe galt!

Kunder kjøpte også

These are the Rubber Sealed Ball Bearings for use on the               Traxxas 1/16 E-Revo and Slash VXL 4WD Vehicles. FEATURES: Blue rubber sealed           May also be used in any vehicle where this size bearing is required INCLUDES: Two Ball Bearings REQUIRES: Installation on the vehicle SPECS:    Outer Diameter: 8mm (0.31")           Inner Diameter: 4mm (0.16")           Width: 3mm (0.12")

49,-

KJØP
RPM Rear A-arms for 1/16 E-Revo - Black Replaces stock Traxxas #7132 Quick Notes: Replaces stock Traxxas #7132 Matching Front A-arms available Matching Axle Carriers available Similar to RPM front A-arms, our rear arms eliminate nearly all of the A-arm slop typically found in stock Mini E-Revo rear A-arms, allowing camber and toe angle settings to be more solidly fixed in position. The result: A smoother, more consistent suspension system with a significantly reduced tendency for the truck to randomly wander while driving. RPM rear suspension arms match the same design elements as our fronts using angled leading and trailing edges. By incorporating a 30-degree bevel in these areas, we reduce the chance of breaking suspension parts since the A-arms will naturally try to transition over objects instead of bluntly plowing into them. RPM Mini E-Revo rear A-arms are sold in sets of four – both upper and both lower A-arms. These miniature E-Revo A-arms, like all RPM molded products.

199,-

Ikke på lager
This is a replacement antenna tube. Antenna tubes are used to help secure and protect reciever antenna wires. INCLUDES: 1 blue antenna tube and 1 black antenna tube cap. SPECIFICATIONS: Length: 11"                 Outside Diameter: 1/8"

29,-

KJØP
Drive Cups. inner

89,-

KJØP
This is the Rear Bulkhead for use on the                    Traxxas Summit Truck RTR FEATURES: Nylon construction           Black in color INCLUDES: One Rear Bulkhead (left and right halves) REQUIRES: Installation on the vehicle

185,-

KJØP
Traxxas 5352T - Rebuild kit (heavy duty), slipper clutch (steel disc/ aluminum friction pads (3)/ spring (1)/ 2x9.8mm pin/ 5x8mm MW/ 5.0mm NL (1)/ 4.0mm NL (1))

119,-

129,-

KJØP
-8%
This is the Battery Compartment Door and Vents for use on                 the Traxxas 1/16 E-Revo and Slash VXL Vehicles. FEATURES: Nylon construction           Black in color INCLUDES: One Battery Compartment Door           Two Vents REQUIRES: Installation on the vehicle

59,-

KJØP
This is the Front and Rear Skid Plates for the Traxxas Revo. FEATURES: Black plastic construction           Front skid plate is a two-piece design           Rear skid plate is a one-piece design INCLUDES: Front and read skid plates          Part #5337           (8) 3X10mm button head screws       Part #2577           (1) 3X30mm button head screws       Part #2582 REQUIRES: Installation on the Traxxas Revo

99,-

KJØP
This is a replacement Half Shaft Set for the Traxxas Revo Truck. This package contains a portion of the telescoping drive shafts. FEATURES: Black plastic construction Blue rubber shaft boots INCLUDES: Two half shaft assemblies REQUIRES: Nothing.  These are direct replacement parts. SPECS:    Length: 120mm (4.7")

89,-

KJØP
This is the Housing for the Front and Rear Differential on the                    Traxxas Summit Truck RTR. FEATURES: Nylon construction           Black in color INCLUDES: One Differential Housing REQUIRES: Installation on the vehicle

59,-

KJØP
  • klarna-dark.png
  • vipps-orange.png
  • mastercard-full.png
  • visa.png
  • paypal.png