Hopp til innhold
-7%

HPI 160544 SD-07WR

Art.nr: 160544

279,-

299,-

- 7%
Hpi Racing

Hpi Racing

** Ikke på lager

Produktet er midlertidig utsolgt. Dersom du ønsker å motta en epost når vi får det inn på lager, kan du legge igjen epostadressen din i skjemaet under.

Informasjon

HPI 160544 SD-07WR

This water-resistant servo is ideal for bashers and racers looking for a tough and durable servo that can be used in wet conditions (e.g. rain, snow, puddles).

Features:
Operating Voltage: 4.8-6V
4.8V: Speed: 0.18 sec/60 degrees, Torque: 6kg-cm
6V: Speed: 0.16 sec/60 degrees, Torque: 7kg-cm
Servo Spline: 25T

Dimensions:
Main case: 40x37.5x20.0mm (excluding mounting tabs, servo spline, & cable outlet)
Mounting tab hole centres: 49.5.0x10mm

Weight: 46g (excluding servo horn)

NOTE: This servo is water-resistant only, meaning it is resistant to splashes and brief contact with water. It is not waterproof and therefore not suitable for submerged used. Before driving in wet conditions, make sure that all electronics fitted to the vehicle are safe to use (marked as water-resistant or waterproof), or that they are fully enclosed and protected from water and moisture (such as in a sealed receiver/battery case). Fans mounted on speed controllers are not water resistant - we recommend to disconnect the fan from the ESC before driving in wet conditions and allow it to dry fully before reconnecting the fan power. Lubricate exposed metal drivetrain parts such as bearings, outdrives and diff shafts before driving in wet conditions. Motors are not intended for submerged use and may be damaged if used when under water. After driving in wet conditions, make sure to rinse off dirt and any corrosive liquids like saltwater with plain water and re-lubricate metal drivetrain parts. 

Produsent

Kunder kjøpte også

This is a pair of 5x40mm Axles for the HPI Savage XS Flux and Bullet Vehicles. FEATURES: Steel construction INCLUDES: Two 5x40mm Axles  

139,-

KJØP
This is a Package of Red P-3 Silicone O-Rings for Hobby Use.  These are used in shocks, absorbing vibration, and many other uses.     FEATURES Silicone construction.   INCLUDES Five P3 o-rings.   REQUIREMENTS Nothing. These are direct replacement parts.   SPECIFICATIONS  Inner diameter: 3mm (0.20")   COMMENTS These o-rings are not limited to use only in HPI vehicles.

39,-

KJØP
HPI  66655 - DRIVE SHAFT 6x65mm (2pcs) THIS PART FITS THE FOLLOWING KITS / PARTS: Savage XS Flux GT-2XS Savage XS Flux Ford F-150 SVT SAVAGE XS FLUX VGJR Savage XS Flux Chevrolet El Camino

139,-

KJØP
82243S ORION WP BRUSH ESC 45A.ORI65130 S-Plug Team Orion 45A brushed motor water proof ESC. LiPo capable. Forward/Reverse.  Genuine Kyosho replacement parts make maintenance fast and easy! 

499,-

549,-

KJØP
-9%
Kvalitets NiMh pakke med meget høye utladingsegenskaper! 7.2v 3300mah Standard StickPack NiMh med T-Plugg/Deans 3300mAh 7,2V Nimh batteri som passer i de fleste rc-produkter som benytter standard stick pakker, slik som bil, båt, fly, startere m.m Leveres med Dean/T-kontakt, skal det brukes på ett produkt med annen batterikobling kan overgang benyttes. Lengde 136mm Bredde 46.6mm Høyde 24.2mm Vekt 420gram inkludert ledning og plugg

299,-

319,-

KJØP
-6%
MOTOR 540 CLASS G-SERIES G27 SINGLE

295,-

KJØP
SkyRC eN18 NiMH Peak Charger - Compact but Versatile Want to get the most out of your batteries? You really need to make sure you can deliver a full charge to your batteries with a SkyRC eN18 Peak Charger. SkyRC eN18 is more than just a peak charger - it's a versatile peak charger capable of charging both electric car battery packs and nitro car receiver packs. This is possible because the SkyRC eN18 offers voltage ranging from 4.8 to 14.4V at 1.2 amp. You can charge 6-8 cell NiMH battery packs as found in most electric cars, trucks, and buggies. With the 1.2 amp charge rate, you can safely fast charge any 4-5 cell nitro car NiMH receiver's pack. Delta-V Peak detection With the Delta Peak detection circuitry, the SkyRC eN18 allows your batteries to reach their full capacity when charging, so you can get the most power and run time from your batteries. It achieves this by using peak detection circuitry that monitors the voltage of the battery pack while it's being charged and automatically shuts the charger off when the packs' voltage peaks and then starts to drop. This is in contrast to a timed charger, where you often end up with a battery pack that's not fully charged. Features: T-Plug Delta Peak Detection Circuitry Compact & Lightweight NiMH Compatible Maximum Output 1.2A Short-Circuit Protection Reverse-Connection Protection Universal-Voltage Input Accurate Voltage High Reliability Lower Operating Temperature High Efficiency Plug and Charge eN18 will start charging on the fly once the correct battery is plugged. Stabilized Output for Maximum Safety With the stable pulse charge, eN18 pumps a fixed 1.2A current to charge your battery reliably. All the chargers have passed the rigorous burn-in process to ensure they are durable enough to withstand use cycles and other operating conditions. Trickle Charge: Optimize the battery Like all batteries to self-discharge, NiMH batteries even have a relatively high self-discharge rate of about 1% per day. Trickle charging can keep NiMH batteries in optimal condition to replenish the charge that is continually draining off. Bi-Color LED: Easy Status at a Glance Steady RED: Standby Flashing GREEN: Charging Steady GREEN: Fully Charged Flashing RED: ERROR Specs: Dimension: 85×50×54mm Weight: 120g Input: AC100V-240V 50/60Hz Battery Type: NiMH Output Voltage: 4.8V-14.4V Output Curent: 1.2A Output Power: 18W Max Battery Cell: 4-8S Output Battery Connector: T-Plug Output Cable Length: 70cm Operating Temperature: 0℃-40℃ Relative Humidity: 5%-75% Storage Temperature: -10℃ - 70℃ Storage Humidity: 5%-75%

229,-

249,-

KJØP
-8%
This is the 5x10mm Ball Bearing Set from Tamiya.     FEATURES Sheilded metal construction Fits a wide variety of components on R/C vehicles     INCLUDES Four 5x10mm Ball Bearings from Tamiya     SPECIFICATIONS Inner Diameter: 5mm Outer Diameter: 10mm Thickness: 4mm

79,-

KJØP
Yeah Racing QUTUS Challenger 50mm Damper Set for 1/10 RC Touring M-Chassis Car Red Description: Yeah Racing new generation of Dampers, the Qutus (Quick Tuning System) allows for you to adjust the damper action without taking the damper apart and having to change oil! Build with the included adjustable pistons to quickly change how much dampening you require. Choice from 1 to 5 holes open in the piston will allow you to tune the damper matching to your track conditions. For the 50mm variation of the QUTUS dampers, included are shock shafts which you can build 52mm (eye-to-eye) dampers when you require that tiny bit more extra length. If adjustable pistons aren't your thing, traditional "fixed" pistons are also included in both three and four hole variants. The shock body has been updated to be of "big-bore" spec. which fills more oil than traditional dampers which gives much more consistent handling in both cold and hot temperatures. Soft, Medium and Hard springs have been included as well.   Feature: For: 1/10 RC Touring M-Chassis Car Material: Aluminum Color: Red Include: QUTUS Dampers (4 pcs) Adjustable Pistons (8 pcs) Fixed Pistons (8 pcs) Hard Springs (4 pcs) Medium Springs (4 pcs) Soft Springs (4 pcs) Damper Oil (1 bottle) Manual:

649,-

KJØP
Description: Aluminum upgrade series for the Tamiya MB-01, upgrade critical parts on the car to get more performance!     Feature:   For: Tamiya MB-01 Material: Aluminum Color: Blue   Include:   Tie-Rod Mount (1 pc) Screws (2 pcs) Ball Studs (2 pcs)

99,-

109,-

KJØP
-9%
Description: Two piece aluminum and graphite damper mount for your Tamiya MB01, lightweight and durable!     Feature:   For: Tamiya MB-01 ( Front or Rear ) Material: Aluminum & Graphite Color: Blue & Black     Include:   Aluminum & Graphite Damper Mount (1pc)

179,-

199,-

KJØP
-10%
Description: Securely mount the servo on your Tamiya MB-01 with this aluminum servo mount, can also act as a heatsink for high power servos!     Feature:   For: Tamiya MB-01 Material: Aluminum Color: Blue     Include:   Aluminum Servo Mount (1pc)

199,-

219,-

KJØP
-9%
  • klarna-dark.png
  • vipps-orange.png
  • mastercard-full.png
  • visa.png
  • paypal.png