Hopp til innhold
Hjem / Radio/Servo/Motor / Radioutstyr / Hitec / Servo Kabler Hitec / Hitec 54612S Heavy Gauge Twisted Wire Aileron Extension 36"

Hitec 54612S Heavy Gauge Twisted Wire Aileron Extension 36"

Art.nr: 54612S

79,-

Hitec

Hitec
** Ikke på lager

Produktet er midlertidig utsolgt. Dersom du ønsker å motta en epost når vi får det inn på lager, kan du legge igjen epostadressen din i skjemaet under.

Informasjon

This is a Heavy Duty 36" Twisted Wire Servo Extension with Hitec-S, JR, Airtronics-Z Connectors.

This extension goes between the receiver and the servo to make the wire longer.
On one end of the wire is a male connector and on the other end of the wire is a female connector.

FEATURES

Gold-plated teminals improve conductivity and prevent oxidation for longer lifespan
Heavier, 20-gauge wire handles higher current loads
Twisted wire design cuts down on electro-magnetic noise (EMI) which can cause radio interference

INCLUDES

One 36" Long Servo Extension w/Hitec-S, JR, Airtronics-Z Style
Connectors

SPECIFICATIONS

Wire Gauge: 20
Wire Color Codes-
JR- Hitec- Airtronics Z-
Brown: ground Black: ground Black: ground
Red: positive Red: positive Red: positive
Orange: signal Yellow: signal Blue: signal

Produsent

Hitec

Hitec

Kunder kjøpte også

Hovedbilde DynoMAX B9201 Heat Shrink Tube Red & Black D2/W3mm x ... Hovedbilde DynoMAX B9201 Heat Shrink Tube Red & Black D2/W3mm x ...
DynoMAX B9201 Heat Shrink Tube Red & Black D2/W3mm x ...
Red & Black Shrink Tube Set - D2mm/W3mm 1+1m Set with 1m red and 1m black polyolefin 2:1 heat shrink tubing suitable for most R/C and hobby electrical wires and connectors but also other applications where you need shrink tubing. Specifications: Diameter: 2mm Width (laid flat): 3mm Length: 1+1 m Color: Red & Black Material Thickness: 0.25 - 0.35 mm Material: Polyolefin (PE) Shrink Rate: 2:1 Radial Shrinkage: 50% Longitude Shrinkage: 5% Shrink Temperature: 70-110°C Operating Temperature: -55°C - 125°C All measurements are before heat shrinking

39,-

KJØP
Hovedbilde Hobbywing 38020352 QuicRun Combo 1080 G2 - 540 13T ...
Hobbywing 38020352 QuicRun Combo 1080 G2 - 540 13T ...
Hobbywing QuicRun WP 1080 G2 Crawler ESC + 555-13T Brushed Crawler Motor Combo Four running modes are available - Fits a variety of control habits and control needs: Forward with brakes Forward & reverse with brakes Forward & reverse Real car running mode The first ”Real Car Mode” The direction of the motor is switchable in real time by using the idle channel on the transmitter. Pull the trigger for "forward" Push the trigger for "brake" Pull the trigger with the "reverse channel" on will give you "reverse" (Requires an open channel on the receiver) This new feature will provide the user with a unique experience unlike any other. Multiple, easy to set parameters 15 Programmable Items let's drivers easily tune their vehicle with the LED Programming Box connected to the programming port. Temperature control upgrade The New design reduces operating temperatures of the ESC by about 15 degrees improving reliability. The ESC also has a fan mount to meet additional cooling needs BEC Upgrade The BEC Upgrade includes maximum output to 6A and provides 6V/7.4V/8.4V output options to support most of the servos on the market. IP67 Protection IP67 Standard for being waterproof and dust-proof for various weather conditions, and driving surfaces. Note: The IP67 protection level mentioned above is splash-resistant, water-resistant and dust-resistant under normal use, and is tested under controlled laboratory conditions. Its effect is in the GB / T 4208-2017 (domestic) / IEC 60529 (overseas) standard to IP67 level. Splash, water and dust resistance are not permanently effective, and the level of protection may decline due to aging. Features: Fully waterproof design for all conditions. (Note: please clean and dry it after use for avoiding rusty connectors) HOBBYWING patented copper heat-conductive plates attached to the MOSFET board allows the internal heat to be quickly transferred to the CNC-machined aluminum reticular heat sink for great heat dissipation. High reliable electronic switch design prevents mechanical switch failure due to dirt, water, dust and etc. Tunable drag brake and drag brake rate for different vehicles, tracks and control feel. Adjustable PWM frequency combined with advanced freewheeling (/DEO) technology guarantees great throttle linearity and driving feel. Innovative real car mode, make the downhill control of the vehicle more stable, and provide new fun for the car. It has the function of using transmitter (AUX channel) to adjust the drag brake force in real time, and switch the drag brake force anytime and anywhere according to the demand. Multiple protections: low-voltage cutoff protection, thermal protection, and throttle signal loss protection. Separate programming port to easily connect the LED program card to the ESC. Single-button ESC programming and factory reset. ESC programming via Hobbywing LED program card Specifications: Type: 1/10, Brushed, Waterproof ESC Cont./Peak Current: 80A/400A Input Voltage: 2-3S Lipo / 5-9S NiMH BEC Output: 6/7.4/8.4V @ 4 (6A Peak) Input Wires: 14AWG-200mm Output Wires: 14AWG-200mm Input Connector: XT60 Output Connectors: 4.0mm Bullet Connectors (Female) Size: 37.2x31.9x18.4mm Weight: 70.2g (w/Wires) Motors: 540 & 550 Size Brushed Motors Vehicles: 1/10 Rock Crawlers Firmware Upgrade: Not Supported ESC Programing via: SET Button on ESC: Supported LED Program Box: Supported LCD G2 Program Box: Not Supported OTA Programmer: Not Supported Program Port: Separate Quicrun 555-11T Brushed Specs: Scale: 1/10 Applications: Crawler, Short Course, Truck Turns: 13T RPM @ 7.4V: 14.000 Input volt: Max 12.6V Slots: 5 Outside Dia: 36mm Length: 58.5mm Shaft Dia: 3.17mm Weight 193g

995,-

1.095,-

KJØP
-9%
Hovedbilde Power HD LW-20MG Waterproof Servo 20kg/0.16s
Power HD LW-20MG Waterproof Servo 20kg/0.16s
The Power HD LW-20MG is the latest servo that features an all-aluminum case, copper and aluminum gears, a powerful coreless motor and it pulls up to 20kg-cm of torque at a speed of 0.16s. The standard sized servo is also waterproof making this a great servo for crawlers, 1/8 scale trucks and buggies. It comes black anodized and with laser-etched graphics.   Spesifications: Torque(4.8V): 18.0 kg-cm (250.0 oz/in) Torque(6.0V): 23.0 kg-cm (319.4 oz/in) Speed: 0.14 sec (4.8V) ? 0.12 sec (6.0V) Operating Voltage 4.8 ~ 6.0 DC Volts Weight: 60.0 g (2.12 oz) Bearing Type Ball Bearing x 2 Motor Type Coreless Motor Gear Type Copper & Aluminum Working frequence 1520 s / 333hz Size: 40.7 x 20.5 x 39.5 mm ( 1.6 x 0.80 x 1.55 in)

449,-

539,-

KJØP
-17%
Hovedbilde Zap PT-20 Adhesives Slo Zap CA- 1 oz
Zap PT-20 Adhesives Slo Zap CA- 1 oz
 This is a 1oz Bottle of Slo-Zap CA Glue from Pacer.      Not safe for foam. For foam applications use epoxy or foam-safe CA. FEATURES: Very high viscosity formula.           Super thick and super strong.           Allows approximately 30-40 seconds for part positioning.           Cures in 90 seconds.           Ideal for fillet forming, gap filling, wing sheeting, laminating,             etc.           Use Zip Kicker to accelerate cure time. INCLUDES: One 1oz Bottle of Slo-Zap CA Glue. SPECS:    1oz (28.4g)

139,-

KJØP
Hovedbilde Tamiya 85011 Spray Lacquer TS-11 Maroon 3 oz
Tamiya 85011 Spray Lacquer TS-11 Maroon 3 oz
  This is a 100ml Spray Can of Synthetic Lacquer Paint from Tamiya. FEATURES: Cures in a short period of time.           Extremely useful for painting large surfaces.           100ml is enough to fully cover two or three 1/24 scale sized car             bodies.           Tamiya spray paints are not affected by acrylic or enamel paints.             Therefore, following the painting of the entire assembly, details             can be added or picked out using enamel and/or acrylic paints.  By             combining three different paints, the decoration of plastic             models will become simpler and more effective.           Available in 52 colors. INCLUDES: One 100ml Spray Can of Synthetic Lacquer Maroon Paint. REQUIRES: Eye, Lung and Skin Protection. COMMENTS: Highly Flammable, Pressurized Container.            Keep out of the reach of children.

109,-

KJØP
Hovedbilde Radient RDNAC010044 XT90 MALE WITH CAP END (ESC END) ...
Radient RDNAC010044 XT90 MALE WITH CAP END (ESC END) ...
 XT90 MALE WITH CAP END (ESC END) (5PCS)

159,-

KJØP
Hovedbilde HPI Z529 FLAT HEAD SCREW M3x15mm (6pcs)
HPI Z529 FLAT HEAD SCREW M3x15mm (6pcs)
Phillips Head FLAT HEAD SCREW

39,-

KJØP
Hovedbilde HPI Racing 86099 - DIFF CASE WASHER 0.7mm (6pcs)
HPI Racing 86099 - DIFF CASE WASHER 0.7mm (6pcs)
Genuine HPI quality spare part for easy maintenance and repairs for HPI's best performance 1/8th scale RTR truck …the Hellfire.

69,-

KJØP
Hovedbilde HPI Z892 Racing Washer 10x12x0.2mm (10)
HPI Z892 Racing Washer 10x12x0.2mm (10)
These are Aluminum Washers by HPI FEATURES: Aluminum Construction Silver in Color INCLUDES: (10) Washers REQUIRES: Installation SPECS:   10mm x 12mm x 0.2mm       (11)

49,-

KJØP
Hovedbilde Traxxas 2872X LiPo 3S 11.1V 5000mAh 25C w/iD Connector
Traxxas 2872X LiPo 3S 11.1V 5000mAh 25C w/iD Connector
This is the Traxxas Power Cell 11.1V 5000mAh 25C 3S LiPo Battery.     FEATURES Semi rigid construction does not require a hard case and eliminates  wire harness connectors that can loosen and fail  Engineered specifically to fit Traxxas models  New high current connector with gold-plated copper terminals and  integrated balance connector  iD Auto Battery Identification allows Traxxas iD equipped chargers to  automatically set and optimize charge settings for specific battery  MAXX cable high-efficiency 12 gauge silicone jacketed wire   INCLUDES Traxxas Power Cell 11.1V 5000mAh 25C LiPo 3S Battery with High  Current Connector and Integrated Balance Plug   REQUIREMENTS LiPo compatible charger such as the Traxxas EZ-Peak Plus,  LiPo charging bag   SPECIFICATIONS  Configuration: 3S1P  Continuous Discharge: 25C (125A)  Max Burst Rate: 50C (250A)  Watt Hours: 55.5  Charge Rate: 1C (5A)  Max Charge Rate: 2C (10A)  Dimensions: 6.1 x 1.02 x 1.7" (155 x 26 x 44mm)  Weight: 13.3oz (376g)   COMMENTS ALWAYS use a LiPo-approved Charger  ALWAYS use a LiPo Cell Balancer  NEVER Charge over 4.20V per cell  NEVER Charge at currents greater than 1C  NEVER Trickle Charge  NEVER allow to Discharge below 3.2V per cell  NEVER disassemble or modify pack wiring in any way or puncture cells  NEVER place on combustible materials or leave unattended during  charging  ALWAYS Charge in a fireproof location  ALWAYS set charger's output volts to match battery volts  ALWAYS keep out of reach of children

995,-

1.095,-

KJØP
-9%
Hovedbilde Hitec HS-5585MH Coreless Hi-Torque Metal Gear Servo
Hitec HS-5585MH Coreless Hi-Torque Metal Gear Servo
 This is the Hitec HS-5585MH High Voltage, High Speed Digital Servo. FEATURES: Rated for 2S LiPo operation           Ideal for 1/10 scale monster trucks, 1/8 scale buggies and truggies,             and high performance airplanes up to 35%           Heavy duty metal gears and dual ball bearings           Coreless motor           Two year limited warranty through Hitec beginning at date of purchase INCLUDES: HS-5585MH Servo with 0.94" (24mm) Round Servo Horn, 1.8" (45mm) Round             Servo Horn, 2.3" (59mm) Double Sided Servo Arm, 1.1" (27mm) Single             Sided Servo Arm, 1.6" (42mm) Four Point Horn, Mounting Hardware and             Instructions SPECS:    Operating Voltage: 6.0 - 7.4V DC                       6.0V                7.4V           Speed:      0.17 sec/60°        0.14 sec/60°           Torque:  194 oz-in (11 kg-cm)   236 oz-in (14 kg-cm)           Size: 1.57 x 0.78 x 1.49" (39.8 x 19.8 x 37.8mm)           Weight: 2.10oz (60g)           Wire Length: 11.8" (30mm)           Wire Gauge: 25AWG           Operating Temperature Range: -4 to 140°F           Idle Current: 4mA           Stall Current: 2100mA @ 6.0V, 2700mA @ 7.2V           Potentionmeter Type: 4 slider 1M cycle COMMENTS: A note on coreless motors-a conventional servo motor has a steel core             armature wrapped with wire that spins inside the magnets. In a             Coreless design, the armature uses a wire mesh that forms a cup             that spins around the outside of the magnet. This arrangement is             much lighter resulting in smoother operation and faster response             time.

995,-

1.095,-

KJØP
-9%
Hovedbilde Hitec 54606s Aileron Extension 36
Hitec 54606s Aileron Extension 36"
This is a Heavy Duty 36" Servo Extension with                     Hitec-S, JR, Airtronics-Z Connectors. This extension goes between the receiver and the servo to make the wire longer.              On one end of the wire is a male connector and on the                  other end of the wire is a female connector.   FEATURES: Gold-plated teminals improve conductivity and prevent oxidation for             longer lifespan.           Heavier, 20-gauge wire handles higher current loads.   INCLUDES: One 36" Long Servo Extension w/Hitec-S, JR, Airtronics-Z Style             Connectors   SPECS:    Wire Gauge: 20           Wire Color Codes-             JR-                             Hitec-              Airtronics Z-             Brown:  ground      Black:  ground      Black: ground             Red:    positive    Red:    positive    Red:   positive             Orange: signal      Yellow: signal      Blue:  signal

65,-

KJØP
Hovedbilde Hitec 57346 Servo Extension 24
Hitec 57346 Servo Extension 24"
This is a 24" Servo Extension by Hitec. FEATURES: This allows you to extend the distance between your             receiver and servo.   INCLUDES: (1) Extension   REQUIRES: Plugging between receiver and servo   SPECS:    Length: 24" (610mm)   COMMENTS: Wire color code: Hitec-                            Black:  negative                            Red:    positive                            Yellow: signal

59,-

KJØP
Hovedbilde Traxxas 2072A Gear Set for Servo 2070/2075
Traxxas 2072A Gear Set for Servo 2070/2075
Gear set (for 2070, 2075 servos)

49,-

KJØP
Hovedbilde Traxxas 6737 Bumper, rear/ bumper mount, rear
Traxxas 6737 Bumper, rear/ bumper mount, rear
Bumper, rear/ bumper mount, rear

89,-

KJØP
Hovedbilde Traxxas 8715 Speed Bit Set Hex Drive (1.5/2.0/2.5mm)
Traxxas 8715 Speed Bit Set Hex Drive (1.5/2.0/2.5mm)
Speed Bit Set, hex driver, 3-piece straight (1.5mm, 2.0mm, 2.5mm), 1/4" drive

359,-

379,-

KJØP
-5%
Hovedbilde Traxxas 6851A Driveshaft assembly, front, extreme ...
Traxxas 6851A Driveshaft assembly, front, extreme ...
Driveshaft assembly, front, extreme heavy duty (1) (left or right) (fully assembled, ready to install)/ screw pin (1)

169,-

189,-

KJØP
-11%
Hovedbilde Traxxas 6852A Driveshaft assembly, rear, extreme heavy ...
Traxxas 6852A Driveshaft assembly, rear, extreme heavy ...
Driveshaft assembly, rear, extreme heavy duty (1) (left or right) (fully assembled, ready to install)/ screw pin (1)

149,-

169,-

KJØP
-12%
Hovedbilde Traxxas 6532 Phone mount for TQi Hovedbilde Traxxas 6532 Phone mount for TQi
Traxxas 6532 Phone mount for TQi
Traxxas TQi & Aton Transmitter Phone Mount Mount a Mobile Device to your TQi or Aton Transmitter The new Traxxas RC Transmitter Phone Mount provides a convenient mounting base for your mobile device on TQi and Aton transmitters. This mount makes monitoring real-time telemetry and adjusting settings simple, keeping your device secured to the radio for easy access. Spring loaded clamps hold a variety of mobile devices to the mount, and the base swivels and tilts to customize the position. Get the most from Traxxas Link telemetry accessories and apps with the new Transmitter phone mount.   Neither a smart-phone or a transmitter is included.  

199,-

219,-

KJØP
-9%
Hovedbilde DynoMAX 9590 Connector MPX pair
DynoMAX 9590 Connector MPX pair
Connector MPX pair

39,-

KJØP
Hovedbilde Zap PT-02 Adhesives Zap-A-Gap CA+ 1 oz
Zap PT-02 Adhesives Zap-A-Gap CA+ 1 oz
   This is a 1oz Bottle of Zap-A-Gap CA+ Glue from Pacer.       Not safe for foam. For foam applications use epoxy or foam-safe CA. FEATURES: Superior gap filling formula.           Medium viscosity.           Allows approximately 7-10 seconds for part positioning.           Average of 20 seconds curing.           Works on oily surfaces also.           Use Zip Kicker to accelerate cure time. INCLUDES: One 1oz Bottle of Zap-A-Gap CA+ Glue. SPECS:    1oz (28.4g)

129,-

139,-

KJØP
-7%
Hovedbilde Traxxas 6493 Gear 34T Pinion XO-1
Traxxas 6493 Gear 34T Pinion XO-1
This is the 34 Tooth 1.0 Metric Pitch Pinion Gear for the Traxxas XO-1 On-Road Car. FEATURES Hardened steel construction Fits 5mm diameter motor shafts INCLUDES 34 Tooth 1.0 Metric Pitch Pinion Gear

69,-

KJØP
Hovedbilde Traxxas 5480X Wheel Wrench Splined 17mm
Traxxas 5480X Wheel Wrench Splined 17mm
NB! Denne erstatter TRX 5480 This is the 17mm Splined Wheel Wrench from Traxxas. FEATURES Nylon construction, black in color  Compatible with the 17mm splined nuts used on many Traxxas vehicles INCLUDES 17mm splined wheel wrench

39,-

KJØP
Hovedbilde Traxxas 6888 Center Rear Drive Hub Slash 4X4
Traxxas 6888 Center Rear Drive Hub Slash 4X4
This is the Front and Rear Center Drive Hub Set for use on the                       Traxxas Slash 4x4 Vehicles. FEATURES: Nylon and steel construction INCLUDES: One Front Center Drive Hub           One Rear Center Drive Hub           One Screw Pin REQUIRES: Installation in drive assembly

59,-

KJØP
Hovedbilde Traxxas 6415 Body Mounts Front/Rear XO-1
Traxxas 6415 Body Mounts Front/Rear XO-1
These are the Body Mounts for the Traxxas XO-1. FEATURES: Molded plastic construction INCLUDES: One each Front and Rear Body Mount

109,-

KJØP

SamiRC Norge AS

© 2026 SamiRC Norge AS - Powered by Mystore.no

Om oss

  • SamiRC Norge AS
  • Nils Lauritssøns vei 34
  • 0870 OSLO
  • Org. nr. MVA 928 644 979 Foretaksregisteret
  • Tlf: 46760019
  • post@samirc.no

Kundeservice

Nyhetsbrev

  • klarna-dark.png
  • vipps-orange.png
  • mastercard-full.png
  • visa.png
  • paypal.png